MV-1620HSA
Quick Setup Guide
Use SDI or HDMI monitors that
support 1920 x 1080 (59.94 or 50)
interlaced or progressive video
signals, or 1280 x 720 (59.94 or 50)
progressive video signals.
Packing list: MV-1620HSA (1), Quick Setup Guide (1), CD (Installation CD 1
including Operation Manuals), AC cord (1), AC cord retaining clip (1 set), Rack
mount bracket set (1 set), Rubber feet
Option items: (installed before shipment) MV-1620PS (including AC cord and
AC cord retaining clip), MV-1620IF, MV-1620DO, MV-1620SNMP, MV-1620RT
(Included with unit) Breakout cable (PC3323-1)
The procedure is shown numbered in the above figure.
1Apply DC power to the MV-1620HSA using the supplied AC cord.
Secure the cord with the supplied AC cord retaining clip.
Ground the unit for your safety.
2Connect an HD-SDI monitor.
3 Connect an HDMI monitor.
4Connect signal source devices, such as video cameras, to the
HD/SD-SDI INPUT and/or COMPOSITE INPUT connectors.
5Connect a PC to be used for remote control to the MV-1620HSA LAN
connector using a LAN cable.
6Change the PC network settings for the connection with the
MV-1620HSA.
Go to Local Area Connection > General > Internet Protocol (TCP/IP) >
General > Properties, then set the IP address and Subnet mask to match that
of the MV-1620HSA.
192.168.0.yyy (yyy is any number from 1 to 254
except for the number set for the MV-1620HSA
unit and gateway number. )
* The MV-1620HSA IP address can be changed via the MV-1620HSA main
unit menu or Remote Controller (supplied software). 192.168.0.10 is the
default IP address.
7Verify outputs to the SDI monitor, HDMI monitor and audio devices
using test signals. (The default output is Output 1. To change the
output, use the (1) OUT1/OUT2 button on the front panel.)
1) Hold down the →button for it to flash, so that a test signal is
output.
2) Press the SHIFT button, then buttons 1 to 8 light sequentially
allowing you to select a format. (1 is the default format in the
below table.)
3) To exit HDMI/SDI/AUDIO test signal selection mode, hold down
the →button for it to go off.
8Install Layout Manager (Remote Controller, Layout Editor, Logo Registry) from the
supplied CD.
1) Install the software, then go to Start > All Programs > FOR-A > MV-1620HS >
MV-1620HS Layout Manager to start the program.
2) Press the (8) Online/Offline button under the menu bar in the main window.
3) The connection dialog appears. Enter the MV-1620HSA IP address, (select a Dual
Output mode*) and select 1 for Preset No., then click OK.
* Dual Output offers 2 operation modes; Simul mode: Outputs 1 and 2 are paired and a
layout or a pair of layouts for 2 screens are controlled as one; Independent mode:
Layouts of 2 outputs are controlled separately.
* If the connection cannot be established, check the LAN connection and the PC
network settings.
4) If you wish to use Hangul (Korean characters), click the Layout button (9) in the
Layout Manager window to open the Layout Editorpage, then select Settings >
Encode > EUC-KR from the menu bar in the Layout Editor page.
9If you are using a monitor other than SDI: 1080/59.94i or HDMI: 1080/59.94p, set
frequency and Interlaced/Progressive settings. Click the Layout button (9) in the
Layout Manager window to open the Layout Editor page.
1) From the menu bar, go to Settings > System. In the System page, go to the System
tab > General tab, then set Frequency and Interlaced/Progressive settings.
10 Select SDI/COMPOSITE for the signal input.
Input signals must be displayed in windows in the 16-split (default) screen. If not, click
the Remote button (10-①in the above figure) in the Layout Manager window to open the
Remote Controller page. Click the Multi button and the Preset (layout) #1 (10-②). Click
the Input Select button (10-③) to open the Input Select dialog. Select the input, then click
OK.
Check to see if the monitor has been properly connected. If nothing still appears on the
monitor, check the monitor’s specification sheet to see if the monitor supports any of the
formats listed in the left table.
If Nothing Appears on the Monitor!
(2) FULL/MULTI
Full screen/Multi-channel
screen selection button
Hold down to output Editor
output screen.
(3) WINDOW
Turns window
selection mode
ON/OFF.
(4) SOURCE
Turns input source selection mode ON/OFF.(Lit: ON）
Hold down to turn SDI/COMPOSITE selection mode.
(Flashing: SDI/COMPOSITE selection is enabled.)
(1) OUT1/OUT2
Switches outputs.
Audio mode
selection
button
1~16: Used to select layouts and
source channels.
MENU button
Hold down：Opens menu
Press：Returns to the
upper layer menu.
Locks front panel
buttons.
ON
OFF
POW ER 1 POW ER 2
POWER 1
POWER 2
FAN
ALARM
GENLOCK
FULL
MULTI
AUTO
WINDOW
OUT 1
OUT 2
SOURCE
AU DIO
1 2
910
3
11
4
12
5
13
6
14
7 8
15 16
SHIFT
MENU LOCK
EN TER
MV-1620HS
MU L T I V I E W E R
→button
Hold down to
output test signals.
Click (8)
↓
Connection
dialog opens
Connection and System Configuration
‚Q ‚P
HD-SDI/SD-SDI/COMPOSITEINPUT
AC100-240V50/60HzIN
SER. NO.
LAN
HD-SDIOUT1
BKGDVIDEO INOUT
HD-SDI OUT2
HDMIOUT1
L R
HDMIOUT2
AUDIOOUT2
L R
AUDIOOUT1
161514131211
ANALOG/ DIGITALAUDIOIN
109876
REFINLTCIN
REMOTE/TALLY
54321
RS-232C/ 422/ 485
‚Q ‚P
HD-SDI/SD-SDI/COMPOSITEINPUT
AC100-240V50/60HzIN
SER. NO.
LAN
HD-SDIOUT1
BKGDVIDEO INOUT
HD-SDI OUT2
HDMIOUT1
L R
HDMIOUT2
AUDIOOUT2
L R
AUDIOOUT1
161514131211
ANALOG/ DIGITALAUDIOIN
109876
REFINLTCIN
REMOTE/TALLY
54321
RS-232C/ 422/ 485
LAN：Connect a PC to run the
supplied software programs.
(Also for connections with
switchers, etc., when an IF
option is installed.)
Remote Controller
(To control inputs
and outputs)
Layout Editor
(To create/edit layouts)
Live Viewer
(To output
video signal
to PC)
Web Browser
(To view the
output video
on PC)
Logo Registry
(To edit/save
logos)
Remote Controller control range
3G/HD/SD-SDI/COMPOSITE INPUT
(Connect video cameras, switchers,
etc, to input video signals.)
LTC IN
(Input a time
code.)
REMOTE/TALLY
(GPIO for tally
and layout
control.)
RS-232C/422/485
(Connect a PC for
remote control.)
REF IN
(Input an
external
reference
signal.)
ANALOG/DIGI
TAL AUDIO IN
(Input analog
or digital audio
signals from
VTR and/or
switcher.)
HDMI OUT1, 2
(Connect
1080/59.94p
monitor.)
HD-SDI OUT1, 2
(Connect
1080/59.94i
monitor.)
AUDIO OUT1, 2
(Connect audio
device for analog
audio signals.)
‚Q ‚P
HD-SDI/SD-SDI/COMPOSITEINPUT
AC100-240V50/60HzIN
SER.NO.
LAN
HD-SDIOUT1
BKGDVIDEO INOUT
HD-SDIOUT2
HDMIOUT1
L R
HDMIOUT2
AUDIOOUT2
L R
AUDIOOUT1
161514131211
ANALOG/DIGITALAUDIOIN
109876
REFINLTCIN
REMOTE/TALLY
54321
RS-232C/422/485
‚Q ‚P
HD-SDI/SD-SDI/COMPOSITEINPUT
AC100-240V50/60HzIN
SER.NO.
LAN
HD-SDIOUT1
BKGDVIDEO INOUT
HD-SDIOUT2
HDMIOUT1
L R
HDMIOUT2
AUDIOOUT2
L R
AUDIOOUT1
161514131211
ANALOG/DIGITALAUDIOIN
109876
REFINLTCIN
REMOTE/TALLY
54321
RS-232C/422/485
BKGD VIDEO OUT
(Cascade connection
output. Connect to
MV-1620DO BKGD IN)
BKGD VIDEO IN
(Cascade connection
input. Connect to
MV-1620DO BKGD OUT)
OUT 2 is supported by the MV-1620DO option.
-。
MV-1620HSA front panel control range
For layouts of
1920x1080
Interlaced /
Progressive
selection
Test
signal
output
HDMI
/SDI
/AUDIO
