FOREDOM MALC30 User manual

QtyDescriptionItem
1Top Panel1
2
Shield Hinge
2
32
M5x6mm Scre
3
1LED Light Box4
1Elbo , 2 1/4"5
1
Back Panel
6
1Right Panel7
1Tray8
1
Bottom Panel
9
1
LED Light
10
1
Front Panel ith Shield
11
1Left Panel12
1
Cordset, Detachable
13
F
FF
FO
OO
OR
RR
RE
EE
ED
DD
DO
OO
OM
MM
M Foredom Electric Company
16 Stony Hill Rd., Bethel, CT 06801 • 203−792−8622
Fax: 203−796−7861 • .foredom.net
}
JW 10/2016
Assembly List
MALC30
Jumbo Work Chamber
with Magnetic LED Light
3
3
1
2
4
5
6
7
9
8
10
11
12
13
Rear Panel
Mounting Bracket
Rear Panel
Mounting Bracket
(Not sho n)

F
FF
FO
OO
OR
RR
RE
EE
ED
DD
DO
OO
OM
MM
M Foredom Electric Company
16 Stony Hill Rd., Bethel, CT 06801 • 203−792−8622
Fax: 203−796−7861 • .foredom.net
}
1. Place the Bottom Panel (Item 9) on a flat surface and attach the bottom section of the
Right Panel (Item 7) by threading four M5x6mm Screws (Item 3) through the aligned
holes using the No. 2 Phillips Screwdriver. Do not fully tighten the screws until step 5.
2. Repeat Step 1 with the Left Panel (Item 12).
3. Attach the Top Panel (Item 1) to the side panels by threading eight M5x6mm
Screws (Item 3) through the aligned holes. The Top Panel is attached to the
Left and Right Panels by four screws each.
4. Attach the Back Panel to the four large panels by threading eight
total M5x6mm Screws (Item 3) through the aligned holes. The Back
Panel is attached to each of the four panels by two screws each.
5. Flush up the five panels and tighten the 24 screws connecting them.
6. Attach the Shield Assembly (Item 11) to the top panel through
the Shield Hinge (Item 2). Thread four M5x6mm Screws (Item 3)
through the Shield Hinges, two screws for each of the two hinges.
7. Lift up the Shield Assembly (Item 11) to allow for the Tray (Item 8) to
be placed on top of the Bottom Panel (Item 9). Also place the magnetic
LED Light (Item 10) inside the Shield Assembly where desired.
8. Place the magnetic LED Light Box (Item 4) on the outside of the chamber. Feed the
wire from the LED Light (Item 10) through the hole in the top panel and insert the cord
into the LED Light Box. Insert the Cordset into the LED Light Box (Item 4).
Jumbo Work Chamber Assembly Instructions
Tools required: No. 2 Phillips Screwdriver
Assembly List
MALC30
Jumbo Work Chamber
with Magnetic LED Light
9. Insert the Elbow Tube (Item 5) into the Back Panel (Item 6) .

QtyDescriptionPart No.Item
1Top Panel Assembly
−−−
1
1
Top Panel
1.1
1
Bushing
1.2
2
Shiel Hinge
−−−
2
32
M5x6mm Screw
−−−
3
1
Han le
−−−
4
2
M5x12mm Screw
−−−
5
2
M5 Nut
−−−
6
1
Switch Box, LEDCP10594
7
1
Cor set, DetachableCP10595
8
1Elbow, 2 1/4"MA8259
1
Back Panel
−−−
10
1
Right Panel
−−−
11
1
Tray
−−−
12
1
Bottom Panel
−−−
13
1
Arm RestMA303
14
7
Bottom PaMA304
15
1
LED Light
−−−
16
1
Knob
−−−
17.1
1
Centering Pin
−−−
17.2
1
Shiel
MA30118
11
M4x6mm Screw
−−−
19
1
Shiel Frame
−−−
20
1
Left Panel
−−−
21
1
Frame GasketMA302
22
20
19
18
17.2
17.1
16 15
14
13
3
12
11
9
10
8
7
543
2
1.1
6
22
21
Parts List
MALC30
Jumbo Work Chamber
with Magnetic LED Light
F
FF
FO
OO
OR
RR
RE
EE
ED
DD
DO
OO
OM
MM
M Foredom Electric Company
16 Stony Hill R ., Bethel, CT 06801 • 203−792−8622
Fax: 203−796−7861 • www.fore om.net
}
JW 9/2016
See Parts List
for MAML10
1.2