FORESIGHT HE04M User manual

1
HDMI (HDBaseT) Matrix Switcher Series
ITEM NO.: HE04M 4 x 4 HDMI (HDBaseT) Matrix Switcher
With the latest and more affordable HDBaseT technology extend HDMI sources up to 100M at
1080p or 1920x1200. HE04M HDMI 4 by 4 Matrix Switcher allows for effortless control of up to 4
devices through IR remote control, RS-232 and the front panel.
HE04M 4 x 4 HDMI (HDBaseT) Matrix Switcher
4 x HDMI inputs , 4 x HDMI Outputs Matrix switcher
Dual Output: local HDMI port or remote RJ45 termination
Work with HE02ER, HE02R receiver at each monitor up to 100 meters over CAT5e/6.
Work with HE02EIR receiver at each monitor up to 70 meters over CAT6a cable.
Three control option: Front panel button, IR remote control, RS232 through remote PC.
Support local/remote IR control to select input/output.
Built in RS232 console port to select input/output.
Built 1 in 4 out IR distributor function, allow the HE04M control each monitor and also
could be using the IR remote control to select the input source from the monitor side.
Uncompressed high definition video 1080p@60Hz 12 bit and 3D capable
HDMI 1.4 video features supported, HDCP compliant.
Built in 4 channel IR & RS232 extender (work with Receiver: HE02EIR, HE02ER,)
Input/Output status could be displayed at front panel LCM & LED.
Optional Model:
RC04 : 4 x 4 Keypad remote control (select HE04M input/output)
Optional CAT5E/CAT6 Receiver Model:
HE02ER: 100m HDMI Receiver
HE02R : 100m HDMI, IR and RS232 Receiver
HE02EIR: 70m HDMI with IR Receiver

2
HE04M Panel View:
HE04M Connection View:
4
4
HDMI IN OUTPUT 1 OUTPUT 2 OUTPUT 3 OUTPUT 4
4
100M 100M 100M 100M
* Under dual Output connection: local HDMI port or remote RJ45 termination
Once you link both HDMI & HDBaseT connection, the output will be effected HDMI port only.
For HDBaseT output must disconnection HDMI link.
SOURCE
1
RS232 *4
HDMI HDBaseT
CONSOLE
RS232
TV
TV
HE02R HE02R HE02R HE02R
RS232 Control
IR TX IR RX
IR Emitter Cable
(IR-CT01)
RS232
IR Remote Control
IR Receiver
IR Receiver Cable
(IR-CR01)
PC、KEYPAD
BD PLAYER
HDMI HDMI HDMI HDBaseT HDBaseT HDBaseT
2 3 4
TV TV TV
TV TV TV
IR
RS232 RS232 RS232
IR IR IR
IR
0
1

3
Back Panel Switch:
POWER LED on Power on
LED off Power off
Front LED Indication:
ON BLUE Power on
RED Standby
LED off Power Off
INPUT 1, 2, 3, 4 BLUE Input Indication
LED off SOURCE no signal
OUTPUT 1, 2, 3, 4 BLUE HDMI output indications
RED HDBaseT output indication
LED off Output unlink
Standby mode: The IR Remote only could control POWER on/off.
Front Button Function:
Power Poweron/standby
UP up
DOWN down
LEFT left
RIGHT right
ENTER select confirm key
MENU back to main menu
*When the sub-menu setting changed, press the ENTER key to complete the setting. If no
press ENTER key, then the setting will be failed.
LCM Panel Function:
4X4 HDMI MATRIX: Power on Main Screen
* When the power on the main screen appears, press the MENU key to enter the main menu

4
Main MENU Option:
* SWITCH SETTING
RS232 SETTING
IR TX SETTING
IR RX SETTING
HDBaseT IR ID
MATRIX IR ID
EDID
FIRMWARE VER.
KEYLOCK
Operation:
Press UP or DOWN key to move * to select an item for setting and press ENTER key
into subpage.
When the selected sub-page setting is completed, press the MENU button to return
to the main page
LCM Main MENU Function Operation:
SWITCH SETTING：(Default: 1 2 3 4)
OUTPUT 1 2 3 4
INPUT 1 2 3 4
This function is used to switch the input/output port, enter the SWITCH SETTING menu. To
press the ENTER key, then the LCM second line INPUT 1 will flash, to press UP or Down button to
select the input port, to press LEFT or RIGHT button to select the modified output, after that
press ENTER to confirm setting.
At HDBaseT port could use IR01 remote control to do a quick input selection
～represent select HDMI input ports 1～4. Press or turn off the video output.
HE04M
HE02R - 1
HE02R - 2
HE02R - 4
HE02R - 3
IR-CR01
IR-CR01
IR-CR01
IR-CR01
HDBaseT - 1
HDBaseT - 2
HDBaseT - 3
HDBaseT - 4
OUTPUT 1 2 3 4 INPUT 1 2 3 4
HDMI INPUT 1 2 3 4
IR01

5
RS-232 SETTING：(Default: FIX MODE)
HDBaseT RS-232 extender function with two mode, enter RS-232 SETTING MENU，press
ENTER, the * will flash, then press UP or DOWN button to select FIX MODE or MATRIX
MODE, press ENTER key to confirm setting.
FIX MODE is one to one transmission, RS-232 port 1 only work with HDBaseT port 1,
RS-232 port 2 only work with HDBaseT port 2, and so on…
HE04M
RS-232 SETTING : FIX MODE
RS-232 MATRIX MODE based on SWITCH SETTING to do RS-232 transmission,
RS-232 port 1 work with HDMI input 1，RS-232 port 2 work with HDMI 2 and so
on…
HE04M
RS-232 SETTING : MATRIX MODE
HE02R - 1
HE02R - 2
HE02R - 4
HE02R - 3
HDBaseT - 1 Projector
RS232 - 4
RS232 - 3
RS232 - 2
RS232 - 1
HDBaseT - 2
HDBaseT - 3
HDBaseT - 4
Projector
Projector
Projector
PC
PC
PC
PC
RS232 Cable
RS232 Cable
RS232 Cable
RS232 Cable
HDMI - 4
RS232 - 4
HDMI - 3
RS232 - 3
HDMI - 2
RS232 - 2
HDMI - 1
RS232 - 1 HDBaseT - 1
HDBaseT - 2
HDBaseT - 3
HDBaseT - 4
Projector
Connect To PC 1
Projector
Connect To PC 1
Projector
Connect To PC 1
Projector
Connect To PC 4
PC 1
PC 2
PC 3
PC 4
HE02R - 1
HE02R - 2
HE02R - 4
HE02R - 3
RS232 Cable
RS232 Cable
RS232 Cable
RS232 Cable
＊ FIX MODE
MATRIX MODE
FIX MODE
＊ MATRIX MODE
OUTPUT 1 2 3 4 INPUT 1 1 1 4
Connect To
HDBaseT - 1
HDBaseT - 2
HDBaseT - 3
Connect To
HDBaseT - 4

6
IR TX SETTING : (Default IR TX: O O O O)
This function could setup the IR signal whether from MATRIX sent to HDBaseT port. To
control remote device, setting O is on, X is off.
After entering IR TX SETTING menu, press ENTER, then LCM second line of text will flash, to press
UP or DOWN button to select O or X, press ENTER to confirm setting.
O:on X:off
HE04M
IR-CR01 HE02R - 1
HE02R - 2
HE02R - 4
HE02R - 3
IR-CT01
IR-CT01
IR-CT01
IR-CT01
TV
TV
TV
TV
HDBaseT - 1
HDBaseT - 2
HDBaseT - 3
HDBaseT - 4
HDBaseT 1 2 3 4 IR TX O X O X
HDBaseT 1 2 3 4
IR TX O X O X

7
IR RX SETTING：(Default IR RX: O O O O)
This function could setup the IR signal whether from HDBaseT sent to MATRIX to control
local device, O is on, X is off.
After entering IR RX SETTING menu, press ENTER, then LCM second line of text will flash, to press
UP or DOWN button to select O or X, press ENTER to confirm setting.
HDBaseT 1 2 3 4
IRRX O X O X
O:on X:off
HE04M
IR-CT01 HE02R - 1
HE02R - 2
HE02R - 4
HE02R - 3
IR-CR01
IR-CR01
IR-CR01
IR-CR01
Player
Remote Control
Player
Remote Control
Player
Remote Control
Player
Remote Control
HDBaseT - 1
HDBaseT - 2
HDBaseT - 3
HDBaseT - 4
HDBaseT 1 2 3 4 IR RX O X O X
Player

8
HDBaseT IR ID：(Default IR ID: 5 5 5 5)
This function could be set to different ID to avoid HDBaseT remote control (IR01) conflicts with
other devices remote control.
After entering HDBaseT IR ID menu, press ENTER, then LCM second line of text will flash, to
press UP or DOWN button to select, press ENTER to confirm setting.
When finish HDBaseT IR ID setting, HDBaseT remote control ( IR01) must also set the same ID
in order to operation in normal.
Remote IR ID setting mode: To press and hold the POWER button, then press the number
button which can be set from 0 to 9, total 10 groups.
★First time to use the remote control or replace new batteries of remote control need
to re-set the remote control IR ID.
HDBaseT 1 2 3 4
IR ID 0 1 2 3
HE04M
HDBaseT - 1
HDBaseT - 2
HDBaseT - 3
HDBaseT - 4
HDBaseT 1 2 3 4 IR ID 0 1 2 3
IR01
＋
＋
＋
＋

9
MATRIX IR ID：(Default IR ID: 4)
This function could be set to different ID to avoid Matrix remote control (IR01) conflicts with
other devices remote control.
After entering MATRIX IR ID menu, press ENTER, then LCM second line of text will flash, to
press UP or DOWN button to select, press ENTER to confirm setting.
When finish MATRIX IR ID setting, MATRIX remote control ( IR01) must also set the same ID
in order to operation in normal.
Remote Control IR ID setting mode: To press and hold the POWER button, then press the
Number buttons which can be set from 0 to 9, total 10 groups.
★First time to use the remote control or replace new batteries of remote control need
to re-set the remote control IR ID.
MATRIX IR ID 4
HE04M
MATRIX IR ID 4
IR01
＋

10
EDID : (Default: LPCM-2CH)
Because the player output display resolution will be based on TV EDID , this Matrix provides two
default EDID mode: ” BUILD-IN MODE” and “COPY MODE”.
BUILD-IN MODE：
This mode supports video resolution 480p, 720p, 1080i / p @ 24/50/60Hz, support LPCM
two-channel audio and 5.1 channel . After enter BUILD-IN MODE menu, press UP or DOWN key
to select LPCM-2CH or LPCM-5.1CH, press ENTER to confirm setting.
COPY MODE：
To fully support the TV resolution and audio mode, the matrix provided copy mode to copy TV
EDID for input source reference. When use the copy mode, recommend to copy the lowest
resolution TV EDID. Otherwise it may cause no picture display if the TV resolution not able to
support the higher resolution.
After entering COPY MODE menu, press UP or DOWN button and then select From OUTPUT to
INPUT. After setting, press ENTER to confirm.
BUILD-IN MODE
COPY MODE
LPCM-2CH
LPCM-5.1CH
HE04M
LPCM-2CH
LPCM-5.1CH
HDMI – 4
EDID
HDMI – 3
EDID
HDMI – 2
EDID
HDMI – 1
EDID
HE04M
HDMI - OUT 4
HDMI - OUT 3
HDMI - OUT 2
HDMI - OUT 1
Player - 4
Player - 3
Player - 2
Player - 1
Player - 4
Player - 3
Player - 2
Player - 1
From OUTPUT : 1
To INPUT : 1
HDMI - IN4
LPCM-2CH
HDMI - IN3
LPCM-2CH
HDMI - IN2
LPCM-2CH
HDMI - IN1
TV1 EDID
From OUTPUT : 1
To INPUT : 1
TV1 EDID

11
FIRMWARE VER. :
Display HE04M Matrix firmware version
KEYLOCK :
KEYLOCK function is to avoid any wrong button press. Under keylock mode press “POWER +
MENU” to unlock
Remote Control Function ( IR01):
Setup the remote control IR ID same as the this Matrix, first time
to use the remote control or replace new batteries of remote control need to re-set the
remote control IR ID.
Local side(HE04M Matrix) IR ID default is 4
Remote side(HDBaseT) IR ID default is 0
To avoid the remote control conflicts with other devices remote control, please use
HDBaseT/MATRIX IR ID SETTING to set the IR ID.
IR remove control ID setup : press and hold POWER button , then press Number keys
Remote control button define :
Symbol LocalSide Remote Side
Power ON/Standby(same as Matrix) off output
LEFT left(same as Matrix) no function
RIGHT right(same as Matrix) no function
UP up(same as Matrix) no function
DOWN down(same as Matrix) no function
ENTER confirm (same as Matrix) no function
MENU menu(same as Matrix) no function
Quick key1 select input 1
Quick key2 select input 2
Quick key3 select input3
Quick key4 select input4
no function no function

12
no function no function
no function no function
no function no function
no function no function
turn off output turn off output
Local side (HE04M Matrix) Remote control Quick key operation:
For example: the output port 1 connect to output port 4 , press the quick key 1 (OUTPUT 1) and then
press the quick key 4 (INPUT 4).
Remote side (HDBaseT) remote control quick key operation: press 1 – 4 to select source input, press
0 to turn off the output.
* Under using quick key operation, LCM screen will jump to the output / input setting page, it won’t
allow to use the front panel button to operate the HE04M Matrix.

13
Computer Local Control Function：（CONSOLE）
This Matrix communication format is 9600,8, N, 1 (9600 bps, 8 data bits, no parity check, 1 stop bit)
Operation Instruction format:
Command + Space + parameters + Enter
TX[x] [y] output x port switch to input y port
PWR [z]
[SYMBOL] [PARAMETER]
--------------- ------------------------------------------------------
x 1 | 2 | 3 | 4 Output 1~4
y 01 | 02 | 03 | 04 | 00 Input 1~4, 00: Off
z 00|01 00:Standby,01:On
Example:
TX1 04 Output 1 switch to input 4
PWR 01 turn off
* The Matrix will reply OK message once correct input, wrong input will reply NG message.
RS-232 Extender function：(Default: FIX MODE)
*Cable connection please refer to the connection view page.
* Transmission baud rate up to 115200 bps.

14
Remote side IR Extender Function:
Tx Function:
Receiving IR signal from 4 sets HDBaseT ports, send out the signal by Tx (connect
with 3.5ψIR Emitter) to control source devices.
Rx Function :
Receiving IR signal from Rx (connect 3.5ψIR Receiver cable) to control remote
monitors at 4 sets HDBaseT ports at the same time.
HDBaseT IR Function:
1. Use IR01 (remote control) to control the Matrix input port switching from receiver
side. (Work with IR-CR01 IR receiver cable)
2 . Using remote control of source device or TV, to control source device or TV.
(Work with IR-CT01 IR emitter cable, IR-CR01 IR receiver cable).
HDBaseT linking cable:
Recommend to use high quality Cat.5e、Cat.6、Cat.6a UTP / STP or FTP cable.
HDBaseT transmission distance:
Transmission distances up to 100 meters, using a lower resolution won’t extend to longer
distance.
If the CAT5e/6 cable connections go through wall socket from the wall outlet to HE02R
receiver, the cable length must less 5 meters between HE02R receiver and wall socket.
The wiring diagram as below:
├Cat.6 MAX 100M───────────── ─────────────┤
┌───┐ ┌─────┐ ┌─────┐ ┌───┐
│HE04M │────│ Wall Jack │──────────────│ Wall Jack │────│ HE02R│
MAX 5M MAX 5M└───┘ └─────┘ └─────┘ └ ─┘

15
HDBaseT RJ45 Pin Define:
Video Link ( TIA/EIA-568-B )
1. Orange-white DATA0 +
2. Orange DATA0 -
3. Green-white DATA1 +
4. Blue DATA2 +
5. Blue-white DATA2 -
6. Green DATA1 -
7. Brown-white DATA3 +
8. Brown DATA3 -
Caution:
1. First time to use HE04M remote control or change new batteries, must set up IR ID.
2. The wiring must away from any equipment with electromagnetic wave, i.e.: microwave,
mobile phone, radio equipment, high voltage, Fluorescent light fixtures, power lines, etc.
3. HDBaseT not regular network device, do not connect with any networking equipments to
avoid damage.
HE04M Standard Package Include:
HE04M Matrix x 1 pcs
IR01 IR Remote Control x 1 pcs
Power Adapter x 1 pcs
HE04MEK Package Include:
HE04M Matrix x 1 pcs
HE02R HDMI Receiver x 4 pcs
IR01 IR Remote Control x 5 pcs
Power Adapter x 5 pcs
HE04MEK Package Include:
HE04M Matrix x 1 pcs
HE02ER HDMI Receiver x 4 pcs
IR01 IR Remote Control x 1 pcs
Power Adapter x 5 pcs
HE04MEIK Package Include:
HE04M Matrix x 1 pcs
HE02EIR HDMI Receiver x 4 pcs
IR01 IR Remote Control x 5 pcs
IR Emitter Cable x 4 pcs
IR Receiver Cable x 4 pcs
Power Adapter x 5 pcs

16
Specification:
Item No. HE04M
HDMI Input Max. Resolution 1080p @ 60Hz 12bi, 3D
Video Input HDMI Type A x 4
HDBaseT RJ45 output Max.
Resolution 1080p at 60Hz 12bit
HDBaseT Max. Distance 100 Meters
Video Output HDMI Type A x 4 and RJ45 x4
HDBaseT RJ45 output Max
Distance 100 meters
IR Input/Output Phone Jack x 2
HDBaseT IR Carrier Frequency 30-60Khz
HDBaseT IR Angle Tx : ±30d degree , Rx : ±55 degree
HDBaseT IR Distance 5m
HE04M IR Receive Angle ±45 degree
HE04M IR Receive Distance 5M
RS232 Input/Output DB9 x 5
Power Adapter DC 12V 4.2 Amp
Power Consumption 2.6 Amp (Max)
Temperature Operation: 0 to 55℃, Storage: -20 to 85℃, Humidity: up to 95%
Dimension mm 483 x 197 x 44
Weight kg 2400
ITEM NO. HE02R (HE04MK Kit receiver, Optional CAT5E Receiver)
Resolution Up to 1080p / 60Hz / 48 bit
Distance 100M (Max)
HDMI Connector Type A
RS-232 Baud Rate Up to 115200 bps / Full Duplex
RS-232 Connector DB9 Male
IR Carrier 30-60Khz / ±10° / 5M / 2 Way
Power Supply DC 5V 2AMP Regulated
Power Consumption 1200mA (Max)
Temperature Operation: 0 to 55℃, Storage: -20 TO 85℃, Humidity: up to 95%
Dimensions 88 x 130 x 30
Weight 270
Item No. HE02ER (HE04MEK Kit receiver,
Optional CAT5E Receiver) HE02EIR (HE04MEIK Kit receiver, Optional CAT5E Receiver)
Resolution Up to 1080p / 60Hz / 12 bit
Distance 100 m (Max) 50 m by CAT5e/6, 70 m by CAT6a
Video Output HDMI Type A x 1
IR Carrier Frequency X 30-60KHz
IR Angle X ±55
IR Distance X 5m
Power Supply Regulated DC5V 2A
Power Consumption 1200mA (Max) 820mA (Max)
Temperature Operation: 0 to 55℃, Storage: -20 TO 85℃, Humidity: up to 95%
Dimensions mm 49 x 92.3 x 25
Weight g 135 135
Rev. B