Shinybow USA SB-5688LCM User manual

INSTRUCTION MANUAL
MODEL : SB-5688LCM
8x8 HDMI MATRIX SWITCHER
8x8 HDMI Matrix Switcher
HDMI Matrix Switcher Series
Thank you for purchasing the SB-5688LCM HDMI Matrix Switcher. You will find this unit easy to install and
highly reliable but it is essential that you read this manual thoroughly before attempting to use 8x8 HDMI Matrix
switcher.
MULTIMEDIA AUDIO AND VISUAL

SAFETY INFORMATION
1. To ensure the best results from this product, please read this manual and all other documentation before operating your equipment.
Retain all documentation for future reference.
2. Follow all instructions printed on unit chassis for proper operation.
3. To reduce the risk of fire, do not spill water or other liquids into or on the unit, or operate the unit while standing in liquid.
4. Make sure power outlets conform to the power requirements listed on the back of the unit. Keep unit protected from rain, water and
excessive moisture.
5. Do not attempt to clean the unit with chemical solvents or aerosol cleaners, as this may damage the unit. Dust with a clean dry cloth.
6. Do not use the unit if the electrical power cord is frayed or broken. The power supply cords should be routed so that they are not
likely to be walked on or pinched by items placed upon or against them, paying particular attention to cords and plugs, convenience
receptacles, and the point where they exit from the appliance.
7. Do not force switched or external connections in any way. They should all connect easily, without needing to be forced.
8. Always operate the unit with the AC ground wire connected to the electrical system ground. Precautions should be taken so that the
means of grounding of a piece of equipment is not defeated.
9. AC voltage must be correct and the same as that printed on the rear of the unit. Damage caused by connection to improper AC
voltage is not covered by any warranty.
10. Turn power off and disconnect unit from AC current before making connections.
11. Never hold a power switch in the “ON” position.
12. This unit should be installed in a cool dry place, away from sources of excessive heat, vibration, dust, moisture and cold. Do not use
the unit near stoves, heat registers, radiators, or other heat producing devices.
13. Do not block fan intake or exhaust ports. Do not operate equipment on a surface or in an environment which may impede the normal
flow of air around the unit, such as a bed, rug, carpet, or completely enclosed rack. If the unit is used in an extremely dusty or smoky
environment, the unit should be periodically “blown free” of foreign dust and matter.
14. To reduce the risk of electric shock, do not remove the cover. There are no user serviceable parts inside. Refer all servicing to
qualified service personnel. There are no user serviceable parts inside.
15. When moving the unit, disconnect input ports first, then remove the power cable; finally, disconnect the interconnecting cables to
other devices.
16. Do not drive the inputs with a signal level greater than that required to drive equipment to full output.
17. The equipment power cord should be unplugged from the outlet when left unused for a long period of time.
18. Save the carton and packing material even if the equipment has arrived in good condition. Should you ever need to ship the unit,
use only the original factory packing.
19. Service Information Equipment should be serviced by qualifier service personnel when:
A. The power supply cord or the plug has been damaged.
B. Objects have fallen, or liquid has been spilled into the equipment.
C. The equipment has been exposed to rain
D. The equipment does not appear to operate normally, or exhibits a marked change in performance
E. The equipment has been dropped, or the enclosure damaged.
THIS SAFETY INFORMATION IS OF AGENERAL NATUREAND MAY BE SUPERSEDED BY INSTRUCTIONS CONTAINED WITHIN THIS MANUAL

TABLE OF CONTENTS
1
SAFETY PRECAUTIONS
Please read all instructions before attempting to unpack, install or
operate this equipment and before connecting the power supply.
Please keep the following in mind as you unpack and install this
equipment:
• Always follow basic safety precautions to reduce the risk of fire,
electrical shock and injury to persons.
• To prevent fire or shock hazard, do not expose the unit to rain,
moisture or install this product near water.
• Never spill liquid of any kind on or into this product.
• Never push an object of any kind into this product through any
openings or empty slots in the unit, as you may damage parts
inside the unit.
• Do not attach the power supply cabling to building surfaces.
• Use only the supplied power supply unit (PSU). Do not use the
PSU if it is damaged.
• Do not allow anything to rest on the power cabling or allow any
weight to be placed upon it or any person walk on it.
• To protect the unit from overheating, do not block any vents or
openings in the unit housing that provide ventilation and allow
for sufficient space for air to circulate around the unit.
DISCLAIMERS
The information in this manual has been carefully checked and
is believed to be accurate. We assume no responsibility for any
infringements of patents or other rights of third parties which may
result from its use.
We assume no responsibility for any inaccuracies that may be
contained in this document. We make no commitment to update or
to keep current the information contained in this document.
We reserve the right to make improvements to this document and/
or product at any time and without notice.
COPYRIGHT NOTICE
No part of this document may be reproduced, transmitted,
transcribed,stored in aretrieval system,or anyof itspart translated
into any language or computer file, in any form or by any means
— electronic, mechanical, magnetic, optical, chemical, manual, or
otherwise — without express written permission and consent
© Copyright 1997. All Rights Reserved.
Version 2.2 MAY 2014
TRADEMARK ACKNOWLEDGMENTS
All products or service names mentioned in this document may
be trademarks of the companies with which they are associated.
CONTENTS
INTRODUCTION & CONTENTS ................................................. 1
FEATURES & SPECIFICATIONS .............................................. 2
FRONT PANEL ........................................................................... 3
REAR PANEL ............................................................................ 6
REMOTE CONTROL ...................................................................7
EDID FUNCTIONS ......................................................................9
TYPICAL APPLICATION ...........................................................12
IR EXTENDER ..........................................................................14
RS-232 SERIAL INTERFACE ..................................................16
LIMITED WARRANTY ...............................................................17
INTRODUCTION
The SB-5688LCM is professional 8x8 matrix routing switch.
Supporting eight (8) HDMI Inputs. Output supported (8) HDMI
and (1) Preview output (same output-01). The SB-5688LCM is
based on the HDMI standard and supports full resolution HDMI
Video with embedded EDID. With a signal bandwidth of 340Mhz,
there is no signal degradation. High Definition Digital signals
can be selected and distributed to any (8) Inputs to (8) outputs
simultaneously. The Switcher is certified as being fully CEC
and HDCP 2.0 compliant, full HD HDMI V1.4a 3D formats, data
rates up to 6.75 Gbps. Supports UXGA/WUXGA/DVI 1920x1200
resolution to any HD displays. The Switcher is certified as being
fully HDMI and HDCP compliant, with RoHS,CE,FCC certification.
Support high resolution HDMI sources routed to HDMI displays,
monitors, projector or audio receivers. The EDID management can
be selected between eight (8) different modes. Control is provided
via Front panel push buttons, IR remote, RS-232 or TCP/IP (not a
web-browser). An RS-232 Windows GUI interface is provided for
matrix routing control (Windows only).
PACKAGE CONTENTS
Check that you have the following components;
• SB-5688LCM Matrix Switcher
• RS-232 V2.0 Protocol Instructions
• Ethernet V2.0 Protocol Instructions
• Master wireless IR Remote Control (SW-5688)
• 19 inch Ear mount bracket (Part # 1U-440L)
• SB-100 IR Extender distance ~984 feet (300M) Receiver set.
• SB-100C IR Extender distance 6ft(2M) Receiver Cable.
• CDContents:Thismanual,WindowsGUI,ISPV1.0Windowsdriver
• RS-232 Cable 6 feet (2M)
• Universal Power Supply: DC12V, 5A, Input: (100~230 VAC,
AC 50/60Hz.)
• ISO Screws
• Users Guide

FEATURES & SPECIFICATIONS
FEATURES
• 8x HDMI with DVI-Audio source devices matrix switched to 8x HDMI output devices.
• HDMI digital Video w/ embedded HDCP, DVI format and CEC/HDCP 2.0 compliant
• Worldwide control EDID modes for HD Video resolutions.
• Link speeds of up to 6.75 Gbps (link clock rate of 340MbHz), Support HDMI 1.4a 3D formats.
• Wide range of HD resolutions from PC XGAto WUXGA1920x1200 and HDTV/DTV HDMI resolutions 480i/480p, 576i/576p, 720p, 1080i & 1080p
• Compatible with all HDMI source devices, PC monitors, Plasma HD display, HDTV and audio receivers or audio amplifiers.
• Digital Video TMDS formats Resolution up to 1080p-60 with Deep color 36-bit.
• DigitalAudio Support : Dolby TrueHD, Dolby Digital, Dolby Digital Plug/ex, DTS, DTS-HD, DTS-HD Master, DTS-EX, PCM, PCM2, LPCM2
• Various User Interface control:
• Windows based GUI control via RS-232 port
• Front Panel push button
• IR wireless remote control
• Ethernet Switcher control
• Third party RS-232 controller (via simple ASCII)
• Support world wide control functions: ALL/OFF/RECALL/ENTER/MEMORY/EDID/LOCK
• Support EDID modes :
• Embedded EDID modes : FSS/H24-3D/H24-3D-M/H36-3D/H36-3D-M/DVI-D 1280x1024-60Hz/DVI-D 1920x1200-60Hz/AUTO
• External modes : Learning mode
• Automatic scanning input & output status via LED show on front panel
• Support IR Remote and IR Extender with distance up to ~ 984 ft (300M) Maximum.
The Switcher will remember that last state during a power cycle. When power is removed and resorted, the last configuration will be invoked.
SPECIFICATIONS
• Type of HDMI Switcher: 8x HDMI inputs To 8x HDMI Outputs Matrix Switcher
• HDMI Support: HD 1080p-@60Hz, H36-bit Deep color, 3D (1.4a) formats
• HDCP / CEC Support: HDCP 2.0 Compliant, CEC Compliant
• Video Bandwidth: Double Data Rates: 340Mhz, Total 6.75Gbps bandwidth
• Digital Video Support: Full HD Resolution: 480i / 480p / 720p / 1080i / 1080p
• Digital Audio Support: Multi Audio Formats 5.1 / 7.1, MAT(MLP), Dolby Digital, Dolby TrueHD, Dolby Digital Plus, DTS, DTS-ES
6.1, DTS-HD, DTS-HD-HRA, DTS-HD Master, (PCM-2CH)
• Controls:
• 1x IR Remote Controller (remote switcher)
• 1x Select & Function buttons on front panel
• 1x IR External port (switch control)
• 1x RS-232 series interface (switch control)
• 1x Ethernet series interface (switch control)
• Preview Output: Support 1x preview output port simultaneously via Output-#1
• Source Status Automatically Scan Sources Inputs via LED
• Function Control Key: ALL / OFF / RECALL / ENTER / MEMORY / LOCK / EDID
• Infrared Frequency: 38 Khz
• IR External Distance: ~1000 feet / 300 meters max
• HDMI I/O Connector: HDMI Type A - SMD 19pin Female Type
• Temperature: 32 °F - 100 °F Operation (0 °C - 38 °C)
• Dimensions (LxWxH): 19* x 9.85 x 1.75 in (*with rackmount bracket) (482 x 250 x 44 mm)
• Rack Mount: Rack Mount 1RU High 19 ” Rack Mount (with rack mount)
• Power Supply: DC12V / 5A, Universal world wide Type 50/60Hz, 100~230 VAC
• Power Consumption: 3880 mA Maximum
• Safety Approvals: CE, FCC, RoHS (2002/95/EC)
• Product Weight: 13 lbs
As product improvements are continuous, specifications are subject to change without notice.
2

3
FRONT PANEL
FRONT PANEL
1. POWER SWITCH
The power switch turns the unit on and off. The LCM will illuminate red to indicate that the switcher is ON and is receiving power.
The Switcher will remember that last state during a power cycle.
When power is removed and resorted, the last configuration will be evoked.
2. INPUT STATUS DISPLAY
Input sources 1 to 8 LCM illuminates blue to indicate that a video source is present on that input.
3. OUTPUT STATUS DISPLAY
Each Output (destination) Channel shows which input (source) is assigned.
4. DESTINATION SELECT BUTTONS
Separate outputs 1 thru 8 select buttons are provided for each destination assignment. Routing can be Source to Destination or one
source to multiple destinations. Example : Press Destination 1,3,5 then press Source 2 will route Input 2 to Output 1,3,5 respectfully.
5. EDID MODE SELECT BUTTONS
Used to select EDID mode using Input buttons #1 and #2.
6. IR SENSOR
The IR sensor receives IR commands from the supplied remote controller or third party IR emitter.
7. SOURCE SELECT BUTTONS
Separate inputs 1 thru 8 select buttons are provided each source selection.

4
FRONT PANEL
FRONT PANEL
8. FUNCTION KEY - ALL
Disables (mute) video on all destinations OR Selects the same source to all destinations.
Option 1
- Press ALL followed by OFF button. The display will show “ 0 “ indicating all destinations have no video selected.
Option 2
- Press ALL followed by Source 1 thru 8. The display will show the Source selected.
- Press ENTER The pre-set source selection will be assigned all destinations.
9. FUNCTION KEY - LOCK
Disables (mute) video to selected channels. Either destinations.
- Press OFF button followed by any Destination channel.
- Press 1 thru 8 output destination. The display will show “ 0 “ for the selected channel indicating no video selected.
10 FUNCTION KEY - RECALL
The system will show previously stored presets, up to a total of 16.
Presets are stored in local memory using Source keys 1 thru 8 or Destination keys 1 thru 8 as the memory preset location.
- Press RECALL button.
- Press 1 thru 8 on either Source or Destination row.
- Press ENTER The pre-set configuration will execute.
Operation completes.
Note: Operation will abort if no keys are dressed within 5 seconds.
11 FUNCTION KEY - ENTER
Press ENTER to confirm entries.

5
FRONT PANEL
FRONT PANEL
12 FUNCTION KEY - MEMORY
The system will show store presets, up to a total of 16.
Presets are stored in local memory using Source keys 1 thru 8 or Destination keys 1 thru 8 as the memory preset location.
- Configure desired matrices.
- Press MEMORY button.
- Press 1 thru 8 on either Source or Destination row.
- Press ENTER to ready memory location.
- Or press MEMORY again to cancel operation.
Operation completes.
Note : Operation will abort if no keys are pressed within 5 seconds.
13. FUNCTION KEY - LOCK
- Press and hold LOCK button for two seconds lockout the front panel.
- Press and hold LOCK button for two seconds to enable the front panel.
14. FUNCTION KEY - EDID
- Press EDID to select new EDID mode or select source row #1 or #2 for LINK source EDID again.
- Press DESTINATION again, press the same DESTINATION # to learn CATx EDID, The EDID for CATx has been learned.
15 19 INCH EAR MOUNT PAIR
Converts desktop to 19 inch rack mount. Bracket (part # 1U-440L) INCLUDED.
Image shows rack mount bracket attached.

6
REAR PANEL
REAR PANEL
1. DC POWER INLET
The Switcher is fitted with a DC power plug input connector. Ensure that the
used is of an approved type and is of sufficient current carrying connector
capacity with the correct voltage and connector polarity. 12Volt DC power
supply 5A Max (Center pin positive).
2. IR EXTENDER CONTROL
Support one of IR Extender (IR input) Extend distance maximum 984 ft (300M)
Note: DO NOT install or remote this connection with the power ON.
3. RS-232 CONNECTION
RS-232 control port to allow for interfacing to a PC, Such as a computer
or touch panel control, to the switcher via this DB-9pin Female connector
for serial RS-232 control.
4. ETHERNET CONNECTION
ETHERNET control port to allow for TCP/IP interfacing to a PC
Such as a computer or touch panel control (not a web-browser),
to the switcher via this RJ-45 Female connector to control switcher.
5. PREVIEW OUTPUT -01 HDMI
Connect a signal link of HDMI direct digital video/audio to this Female
HDMI connector. This connector supports HDMI digital video/audio and
DVI digital video sources.
Preview port HDMI signal as the same as Output 1
6. INPUTS- 1,2,3,4,5,6,7, & 8 HDMI
Connect a signal link of HDMI direct digital video/audio to this Female
HDMI connector. This connector supports HDMI digital video/audio and
DVI digital video sources.
HDMI Digital Video/Audio, Connector with fix screw Input 1 ~ Input 8
7. OUTPUTS- 1,2,3,4,5,6,7 & 8 HDMI
Connect a signal link of HDMI direct digital video/audio to this Female
HDMI connector. This connector supports HDMI digital video/audio and
DVI digital video sources.
HDMI Digital Video/Audio, Connector with fix screw Output 1 ~ Output 8
Power Jack:
DC Jack - Inner OD O 2.1mm (+ )
Outside OD O 5.5mm (GND)
Power input - 12VDC, 5A
IR Extender Jack: Female Jack - inner
OD O 3.5 mm
Remote port : DB-9pinFemale connector
Remote port : Control the switcher RJ-45
Female connector
Ethernet Port: Note: the Ethernet port and
RS-232 port cannot be used simultaneously.
Any connection to the Ethernet port will disable
serial commands send to the RS-232 port.
HDMI digital video/audio connector:
HDMI Female connector.
Note: With the proper adapters, the switcher
can be used with DVI digital video signals
HDCPcompliant. DVI does not support audio.
HDMI digital video/audio connector:
HDMI Female connector.
Note: With the proper adapters, the switcher
can be used with DVI digital video signals
HDCPcompliant. DVI does not support audio.
HDMI digital video/audio connector:
HDMI Female connector.
Note: With the proper adapters, the switcher
can be used with DVI digital video signals
HDCP compliant.

REMOTE CONTROL
Before making any connections to the switcher. Observe the following:
> Ensure the mains voltage supply matches the label on the
supplied plug-pack (+/- 10%)
> Ensure that the power switch is OFF
> Ensure that all system grounds (earth) are connected to a
common point.
>Avoid powering equipment within a system from multiple power
sources that may be separated by large distances
> Connect all audio video sources and destination equipment
> Power up all source and destination audio-visual sources
> For each destination output select the appropriate input source
by using the front panel input 1~8 select buttons. The supplied
IRremotecontrol.OrthroughtheRS232serialcommunications
port.
> Upon power up the switcher will return to its last used setting
before powered down.
REMOTE CONTROL
IR REMOTE : SW-5688
IR REMOTE CONTROL KEY :
1. / 2. SWITCH 1 POWER ON or OFF
Controller with a separate power ON and OFF
3. DESTINATION : 1 thru 8 OUTPUT SELECTION
Press the destination button to select the output display channel.
4. SOURCE : 1 thru 8 INPUT SOURCE SELECTION
Press input 1~8 sources with selection button
5. FUNCTION KEY
ALL - function selection button
OFF - function selection button
EDID - function selection button
RECALL - function selection button
MEMORY - function selection button
ENTER - function selection button
LOCK - function selection button
7

REMOTE PROTOCOL COMMANDS
IR REMOTE CUSTOM AND DATA CODES (NEC STANDARD)
HOW TO SETUP IR CODES :
CUSTOM CODE : 09F6
POWER ON : 09F6 A15E
POWER OFF : 09F6 A25D
ALL : 09F6 B04F
OFF : 09F6 B14E
EDID : 09F6 B748
LOCK : 09F6 B54A
RECALL : 09F6 B24D
MEMORY : 09F6 B44B
ENTER : 09F6 B34C
PRESS DESTINATION - # then PRESS SOURCE - #
DESTINATION #1 : 09F6 10EF
DESTINATION #2 : 09F6 20DF
DESTINATION #3 : 09F6 30CF
DESTINATION #4 : 09F6 40BF
DESTINATION #5 : 09F6 50AF
DESTINATION #6 : 09F6 609F
DESTINATION #7 : 09F6 708F
DESTINATION #8 : 09F6 807F
SOURCE #1 : 09F6 01FE
SOURCE #2 : 09F6 02FD
SOURCE #3 : 09F6 03FC
SOURCE #4 : 09F6 04FB
SOURCE #5 : 09F6 05FA
SOURCE #6 : 09F6 06F9
SOURCE #7 : 09F6 07F8
SOURCE #8 : 09F6 08F7
For example;
Select Destination # 1 to show Source #1~8,
The IR Data Code list :
Destination # 1 , Source #1 09F6 10EF 09F6 01FE
Destination # 1 , Source #2 09F6 10EF 09F6 02FD
Destination # 1 , Source #3 09F6 10EF 09F6 03FC
Destination # 1 , Source #4 09F6 10EF 09F6 04FB
Destination # 1 , Source #5 09F6 10EF 09F6 05FA
Destination # 1 , Source #6 09F6 10EF 09F6 06F9
Destination # 1 , Source #7 09F6 10EF 09F6 07F8
Destination # 1 , Source #8 09F6 10EF 09F6 08F7
8