Forno FRHRE5346-30 User manual

RANGE HOOD INSTRUCTION MANUAL
FRHRE5346-30/36
5011160
Conforms to UL STD. 507
Certified to CSA STD. C22.2 NO.113
IMPORTANT:
READ AND SAVE THESE INSTRUCTIONS
NOTICE:
Installer: Leave this guide with the homeowner
Homeowner: Keep this guide for future reference

8
9
8HOW TO REPLACE THE LED LAMP
TROUBLESHOOTING

Rated Voltage: 120V/60Hz
Light Power: LED Lamp Max 6W total
Motor Power: 230W
Total Power: 236W
Air outlet diameter: 5 7/8"
1

2

FRHRE5346-30
ij"
(150mm)
10 3/8"
(263mm)
11 27/32"(301mm)
11 1/8"
(282mm)
29" (736mm)
29 13/16"(757mm)
3

ij"
(150mm)
10 3/8"
(263mm)
11 27/32"(301mm)
11 1/8"
(282mm)
32 1/2"(826mm)
33 3/8" (847mm)
FRHRE5346-36
The hood is operated using the push button on the front panel.
The light switch turns the lamps on and off. The blower switch
turns the blower on to three speed settings:
- OFF
1 - LOW SPEED
2 - MEDIUM SPEED
3 - HIGH SPEED
4

5

ij
(165mm)
min44 3/32"(1120mm)
min25 1/2" (650mm)
1. Fix the metal adapter to the air outlet with 2 screws ST2.9*8. and install the blade to the air
outlet. Please refer to Pic. 1.
Screw (ST2.9*8)
Blade
1.
6

Duct
Tape
(Not
provided)
Filter
Oil cup
Filter
Oil cup
The installation is now complete.
Please cut the hole on the cabinet board. The cut out size for
FRHRE5346-30 would be 10 1/2"* 29 1/8"(267*740mm). The
cut out size for FRHRE5346-36 would be 10 1/2"* 32
11/16"(267*830mm). It’s required to have the cabinet board
thickness to be Min 25/32" (20mm). Push the range hood
upward to the cabinet hole and fix the hood from inside to the
cabinet board with 6 screws ST3.9*25. Please refer to Pic. 4.
4.
Min 25/32" (20mm)
FRHRE5346-30: 10 1/2"* 29 1/8"(267*740mm)
FRHRE5346-36: 10 1/2"* 32 11/16"(267*830mm)
7

HOW TO REPLACE THE LED LAMP?
TROUBLESHOOTING
1. Take off the baffle fitler. Loose the screws showed on Pic 1 and take out the oil cup.
2. Use the screw driver to push the LED lamp out of the panel through the hole.Please refer to
Pic 2 below.
3. Disconnect the LED terminator and then replace it with new LED lamp. And reconnect the
terminator. Fix the new lamp back to position.
4. Install the oil cup back to position and fix the 2 screws back to position.Install the filters back
to position. Please refer to Pic.4 below.
1. 2. 3. 4.
Filter
Led lamp
with terminator
Oil cup
Filter
Oil cup
Led lamp
with terminator
Issue Possible Cause / Solution
The range hood doesn't turn on
•Check if the range hood is plugged in. Make sure that all
power is turned ON, the fuse isn't blown and all electrical
wirings are properly connected.
The range hood turns on but the
LED light doesn't
•Replace the defective LED assembly. Refer to "HOW TO
REPLACE LED LAMP" section.
The range hood vibrates when
the blower is on
•Check and tighten the mounting screws to secure the
hood to the cabinet or wall properly.
The blower or fan seems weak
•Check that the duct size used is at least 6” Range hood
WILL NOT function efficiently with insufficient duct size.
For example: 6” duct over 7” top vent and not sealed
properly.
•Check if the duct is clogged or the damper (half-circular
flapper) is not installed correctly or opening properly. A
tight mesh on a side wall cap might also cause restriction
to the air flow.
8

9

9
10
9COMMENT REMPLACER LA LAMPE LED
DÉPANNAGE
5

1

Nettoyez les filtres à graisse après une période de temps spécifiée.
2

3

FRHRE5346-30
ij"
(150mm)
10 3/8"
(263mm)
11 27/32"(301mm)
11 1/8"
(282mm)
29" (736mm)
29 13/16"(757mm)
ij"
(150mm)
10 3/8"
(263mm)
11 27/32"(301mm)
11 1/8"
(282mm)
32 1/2"(826mm)
33 3/8" (847mm)
FRHRE5346-36
4