Forno FRHRE5346-48 User manual
RANGE HOOD INSTRUCTION MANUAL
FRHRE5346-48/60
5011160
Conforms to UL STD. 507
Certified to CSA STD. C22.2 NO.113
IMPORTANT:
READ AND SAVE THESE INSTRUCTIONS
NOTICE:
Installer: Leave this guide with the homeowner
Homeowner: Keep this guide for future reference
07/17/2023
Cusmer Care
9
9
8HOW TO REPLACE THE LED LAMP
TROUBLESHOOTING
Rated Voltage: 120V/60Hz
Light Power: LED Lamp Max 8W total
Motor Power: 230W
Total Power: 238W
Air outlet diameter: 5 7/8"
1
2
FRHRE5346-48
φ5 7/8"
(150mm)
46 3/8'' (1178mm)
47 1/8'' (1197mm)
φ5 7/8"
(150mm)
10 3/8"
(263mm)
11 1/8"
(282mm)
11 27/32"
(301mm)
7/8"(22.5mm)
4 3/8"
(110mm)
1/2'' (14mm)
7 1/8''(181mm)
1 1/2'' (38mm)
6 3/4"(171mm)
4 1/8"(104mm)
3 1/2"(89mm)
1 5/32''(29mm)
FRHRE5346-48---View from the top (exhaust & power cord location)
3
FRHRE5346-60
The hood is operated using the push button on the front panel.
The light switch turns the lamps on and off. The blower switch
turns the blower on to three speed settings:
- OFF
1 - LOW SPEED
2 - MEDIUM SPEED
3 - HIGH SPEED
φ5 7/8"
(150mm)
58 3/16'' (1478mm)
58 15/16''(1497mm)
φ5 7/8"
(150mm)
10 3/8"
(263mm)
11 1/8"
(282mm)
11 27/32"
(301mm)
7/8"(22.5mm)
4 3/8"
(110mm) 1/2'' (14mm)
7 1/8''(181mm)
1 1/2'' (38mm)
6 3/4"(171mm)
4 1/8"(104mm)
3 1/2"(89mm)
1 5/32''(29mm)
FRHRE5346-60---View from the top (exhaust & power cord location)
4
5
Note 1: Before attaching the hood to the wall unit, drill 2
holes of 6 1/2" diameter into the wall unit.
Note 2: In any case, check the position of the power outlet
where the power cable will run, since a hole might have to
be made in the wall unit to accommodate it.
1.Fix the metal adapter to the air outlet with 4 screws ST2.9*8. And install the blade to the air
outlet. Please refer to Pic. 1.
φ6 1/2"
(165mm)
φ6 1/2"
(165mm)
min44 3/32"(1120mm)
min25 1/2"
(650mm)
Screw (ST2.9*8)
Blade
1.
6
Fix the duct to the air outlet with tape. Please refer to Pic. 2.
Hold the filter lock and push the fiter backword to take off the filters. Release the 3 screws
indicated in Pic. 3 and take off the oil cup.
Please cut the hole on the cabinet board. The cut out size for FRHRE5346-48 would be 10
1/2'' * 46 15/32''(267 * 1180mm).
The cut out size for FRHRE5346-60 would be 10 1/2'' * 58 1/4''(267 * 1480mm). It's required
to have the cabinet board thickness to be Min 25/32'' (20mm). Push the range hood upword
to the cabinet hole and fix the hood from inside to the cabinet board with 8 screws ST3.9 *
25. Please refer to Pic. 4.
2.
3.
4.
4.
3.
Filter
Oil cup
Tape
(Not provided)
Duct
2.
FRHRE5346-48: 10 1/2'' * 46 15/32'' (267 * 1180mm)
FRHRE5346-60: 10 1/2'' * 58 1/4''(267 * 1480mm)
Min 25/32'' (20mm)
Screw (ST3.9*25)
7
HOW TO REPLACE THE LED LAMP?
1. Take off the baffle fitler. Loose the screws showed on Pic 1 and take out the oil cup.
2. Use the screw driver to push the LED lamp out of the panel through the hole.Please refer to
Pic 2 below.
3. Disconnect the LED terminator and then replace it with new LED lamp. And reconnect the
terminator. Fix the new lamp back to position.
4. Install the oil cup back to position and fix the 3 screws back to position.Install the filters back
to position. Please refer to Pic.4 below.
The installation is now complete.
Install the oil cup back to position and screw back the 3 screws. Install the filters back to
poisiton. Hold the filter lock and push back the filter towards the oil cup. And then push it back
to position. Then the installation is done. Please refer to Pic.5.
5.
Filter
Oil cup
5.
Led lamp
with terminator
Oil cup Oil cup
Led lamp
with terminator
Filter
Filter
8
TROUBLESHOOTING
Issue Possible Cause / Solution
The range hood doesn't turn on
•Check if the range hood is plugged in. Make sure that all
power is turned ON, the fuse isn't blown and all electrical
wirings are properly connected.
The range hood turns on but the
LED light doesn't
•Replace the defective LED assembly. Refer to "HOW TO
REPLACE LED LAMP" section.
The range hood vibrates when
the blower is on
•Check and tighten the mounting screws to secure the
hood to the cabinet or wall properly.
The blower or fan seems weak
•Check that the duct size used is at least 6” Range hood
WILL NOT function efficiently with insufficient duct size.
For example: 6” duct over 7” top vent and not sealed
properly.
•Check if the duct is clogged or the damper (half-circular
flapper) is not installed correctly or opening properly. A
tight mesh on a side wall cap might also cause restriction
to the air flow.
9
FRHRE5346-48/60
A
a
a
a
a a :
a
10
10
9COMMENT REMPLACER LA LAMPE LED
DÉPANNAGE
5
1
This manual suits for next models
1
Table of contents
Languages:
Other Forno Ventilation Hood manuals
Forno
Forno FRHRE5346-30 User manual
Forno
Forno FRHWM5029-30 User manual
Forno
Forno FRHUC5227-30 User manual
Forno
Forno FRHRE5312-44 User manual
Forno
Forno FRHWM5029-36HB User manual
Forno
Forno FRHWM5029-30HB User manual
Forno
Forno FRHRE5337-30 Assembly instructions
Forno
Forno FRHWM5029-36HB User manual
Forno
Forno FRHWM5029-36 User manual
Forno
Forno FRHWM5084-30 User manual
Popular Ventilation Hood manuals by other brands
Beko
Beko BHCA66741BBHF user manual
IKEA
IKEA UNDERVERK instructions
Miele
Miele DAS 4630 Operating and installation instructions
Sirius Satellite Radio
Sirius Satellite Radio SL920 FRESCO Series installation instructions
ETNA
ETNA AI752 Instructions for use
Blanco
Blanco BRC90BX Use and care and installation instructions