Fort ECSPCAMPT User manual

Elite Security Products
Redditch B98 8YN
Preparation For Use
Ensure that the smart phone is connected to the same Wi-Fi
network that you would like to attach the device.
Ensure that you have a mobile device running iOS 8 or higher
or Android 4.1x or higher and a 2.4GHz Wi-Fi connection.
Contents
• 1 x ECSPCAMPT
• 1 x Power Adapter
• 1 x USB Cable
• 1 x Bracket
• 1 x Adhesive Tape
• 1 x Set of installation screws
• 1 x Reset Pin
• 1 x User Manual
General
Our products are designed to comply with the
recommended codes and practice, and is to be
installed and serviced by competent persons in
accordance with the relevant regulations.
Smart Indoor Pan & Tilt Camera
ECSPCAMPT
Products bearing this mark
are compatible with the Clicksmart+ APP
Product Diagram
IR sensor
2 Megapixel lens
Reset hole
Microphone
Micro SD card slot
Installation
The indoor camera is designed for table top use or ceiling mount using the supplied bracket;
Base
Base
Download the ClickSmart+ App on your
mobile device from the App Store or
Google Play.
Sign in or Register following the
instructions on the ClickSmart+ App.
Connect the supplied power adapter to the camera and apply power, the camera will operate after 60secs.

Elite Security Products
Redditch B98 8YN
Telephone : [phone]
Fax: [phone]
Email : [email protected]
Web : www.espuk.com
E&OE - Errors and omissions excepted.G21
9:41 AM 100% 9:41 AM 100% 9:41 AM 100%
Home Smart Me
ClickSmart+
Hub
Window &
Door Sensor
Humidity &
Temperature...
PIR Smart PT Camera 2G Switch
Module
2G Dimming
Module
Smart Double
Socket
Smart Single
Socket
Add Manually Auto Scan Cancel Net Pairing Mode
Reset the device first.
①Set up the device as per the
installation instructions
②Hold the connection button for 5 seconds.
The LED should rapidly flash green.
③The device is now in pairing mode.
Confirm Indicator Is Blinking
Guidance
APP Pairing
The ClickSmart+ app will guide you through:
Entering the Wi-Fi Network and Password.
Using the Camera to scan a QR code.
Connecting the Device.
Resetting the Device
If the Camera needs to be reset, connected to a new Wi-Fi network, or if it needs to be paired with a new master
account, remove the device from the app, prior to resetting the device.
>Unit requires a minimum of 2 Mbps (upload/download)
>If the signal strength of your Wi-Fi router is weak: Change
router/camera relative position to receive better signal, Use Wi-Fi
repeater/extender to maximize the range of your Wi-Fi router.
>If the device is installed on a new network the unit will require resetting
>If the camera needs to be added to a new account, unbind the
device from the first account prior to resetting the device.
For more product information please visit the ESP website
Turn the Camera on, press the reset button in for 5 seconds, The camera will beep and say “restore factory setting”.
The system settings will be restored to factory default.
1. Set up the device as per the installation instructions.
2. Once powered, the unit should say “Camera start”,
followed by “Please configure network”.
3. On the Clicksmart+ app, click on the add icon “+”,
then click “Smart PT Camera”, and then follow the
on screen instructions.
9:41 AM 100% 9:41 AM 100% 9:41 AM 100%
Home Smart Me
Smart PT Camera
Smart Camera Settings
Screenshot Speak Record
Playback Alarm Photo album
Device Name Smart PT Camera
Low
Share Device
Device Infromation
Use Echo
FAQ & Feedback
Firmware Infromation
Basic Function Settings
Motion Detection
Remove Device