Forte F2412MVD650SS User manual

24" Microwave Drawer
F2412MVD650SS
INSTALLATION MANUAL
SPECIAL WARNING
INSTALLATION AND SERVICE MUST BE PERFORMED BYA QUALIFIED INSTALLER.
IMPORTANT: SAVE this installation manual FOR LOCAL ELECTRICAL INSPECTOR'S USE.
READ AND SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE.
CLEARANCES AND DIMENSIONS
For SAFETY CONSIDERATIONS do not install drawer in any combustible cabinetry, which is not in accord
with the stated clearances and dimensions on pages 2 and 3. See Figure 1.
UNPACKING YOUR MICROWAVE DRAWER
·Remove all packing materials from inside the
Microwave Drawer.DO NOT REMOVE THE
WAVEGUIDE COVER，which is located on the top
of the Microwave Drawer.
·Remove the feature sticker, if there is one .Check
the drawer for any damage, such as misaligned or
bent drawer, damaged drawer seals and sealing
surfaces, broken or loose Microwave Drawer
guides and dents inside the cavity or on the front
side of the drawer. If there is any damage, do not
operate the Microwave Drawer and contact your
dealer or a FORTE AUTHORIZED SERVICER.
IMPORTANT NOTES TO THE INSTALLER
·Read all of the Installation Manual before
installing the Microwave Drawer.
·Remove all packing material before connecting
the electrical supply.
·Observe all governing codes and ordinances.
·Be sure to leave these instructions with the
consumer.
IMPORTANT NOTES TO THE CONSUMER
Keep this manual with your Operation Manual for
future
reference.
·As when using any microwave oven generating
heat, there are certain safety precautions you
should follow. These are listed in the Operation
Manual. Read all and follow carefully.
·Be sure your Microwave Drawer is installed and
grounded properly by a qualified installer or
service technician.
IMPORTANT SAFETY INSTRUCTIONS
WARNING if the information in this manual is not
followed exactly, a fire or electrical shock may result
that could cause property damage, personal injury or
death.
WARNING To reduce the risk of tipping ,the
Microwave Drawer must be secured by a properly
installed Anti-Tip block.
·This Microwave Drawer must be electrically
grounded in accordance with local codes.
·Make sure the wall coverings and the cabinets
around the Microwave Drawer can withstand the heat
generated by the Microwave Drawer.
WARNING Never leave children alone or
unattended in the area where a Microwave Drawer
is in use. Never leave the drawer open when the
microwave is unattended.
WARNING Stepping ,leaning or sitting on the drawer
may result in serious injuries and can also cause
damage to the Microwave Drawer.
·Do not use the Microwave Drawer as a storage
space .This creates a potentially hazardous
situation.
·Check that the time-of-day is in the display. IF not,
touch Stop/Clear to prevent unintended use.
1

CLEARANCES AND DIMENSIONS
·Dimensions that are shown in Figure 1 must be
used. Given dimensions provide minimum
clearance. Locate electrical outlet in the shaded
area in the upper left-hand corner of the cutout.
See Figure 3.
·Contact surface must be solid and level. Pay
special attention to the floor on which the
Microwave Drawer will sit. The floor of the opening
should be constructed of plywood strong enough
to support the weight of the oven (about 100
pounds).
·Check location where the Microwave Drawer will
be installed for proper electrical supply
·Your oven can be built into a cabinet or wall by
itself or under a gas or electric wall oven.
·Be sure that the clearance of the floor between
the wall oven and the microwave drawer is a
minimum of 2-inches.
·The microwave interior will easily accommodate a
9" x 13" oblong dish or a bag of microwave
popcorn.
MICROWAVE DRAWER MEASUREMENTS
IMPORTANT Always allow sufficient power cord
length to the electrical outlet to prevent tension.
Always check electrical codes for requirements.
Figures 1 and 2 contain many Microwave Drawer
measurements for reference when planning the
drawer's location .This Microwave Drawer can be
installed below any electric or gas wall oven.
*Can also be installed using an electrical outlet in an
adjacent cabinet within the area where the provided
electrical cord can reach. Power cord access hole in
cabinet should be a minimum l 1/2" diameter hole and
debarred of all sharp edges.
Anti Tip
block
Floot must
support 100lbs
Suggested electrical
outlet location
24''
cabinet min
36''
countertop
height
5''
4''
2
3
12
''
min
depth
22
18
'
opening
Allow
7
8
''
overlap
Al
low
716
'
'
ov
erl
ap
19''to
top
of
floor
14
1316
''
opening
14
1316
''
tobottomof
Anti-tipblock
(6'')
3
1
2
'
'
Allow316''
overlap
Allow
78
''
overlap
Figure 1
Figure 2
2
15''
23 5/16"
1 9/16"
23 5/16"
14 15/16"
1
5
'
'
a
u
to
d
r
a
w
e
r
o
p
e
n
i
n
g

ANTI-TIP BLOCK
NORMAL INSTALLATION STEPS
ANTI-TIP BLOCK INSTALLATION INSTRUCTIONS
To reduce the risk of tipping of the drawer, the Anti-Tip
block must be properly installed located 14
13/16-inches above the floor on which the Microwave
Drawer will sit. The 6-inch Anti-Tip block must be
provided by the installer. See Figures 1 and 3. The
Anti-Tip block prevents serious injury that might result
from spilled hot liquids.
If the Microwave Drawer is ever moved to a different
location, the Anti-Tip block must also be moved and
installed , When installed to the wall make sure that
the screws completely penetrate the dry wall and are
secured in wood or metal so that the block is totally
stable. When fastening, be sure that the screws do not
penetrate electrical wiring or plumbing.
ELECTRICAL OUTLET
The electrical requirements are a 120 volt 60 Hz, AC
only, 15 amp. or more protected electrical supply. It is
recommended that a separate circuit serving only this
appliance be provided.
The drawer is equipped with a 3-prong grounding plug,
It must be plugged into a wall receptacle that is
properly installed and grounded. Should you only
have 2-prong outlet, have a qualified electrician install
a correct wall receptacle.
Note: If you have any questions about the grounding
or electrical
Instructions, consult a qualified electrician or service
person.
*Can also be installed using an electrical outlet in
an adjacent cabinet within the area where the
provided electrical cord can reach.
Always check electrical codes, for requirements.
GROUNDING INSTRUCTIONS
This appliance must be grounded. The Microwave
Drawer is equipped with a cord having a grounding
wire with a grounding plug. It must be plugged into a
wall receptacle that is properly installed and grounded
in accordance with the National Electrical Code and
local codes and ordinances. In the event of an
electrical short circuit, grounding reduces risk of
electric shock by providing an escape wire for the
electric current.
WARNING _Improper use of the grounding plug
can result in a risk of electric shock. Do not use an
extension cord. If the power supply cord is too
short, have a qualified electrician or serviceman
install an outlet near the appliance.
S
u
gg
e
st
e
d
el
e
ct
r
ic
a
l
ou
t
le
t
lo
c
at
i
on
5
''
4
'
'
Anti Tip
block
(6'')
3
12
''
Figure 3 Figure 4
3

DRAWER INSTALLATION
1. Place the drawer adjacent to the wall or cabinet opening.Plug the power supply cord into the electrical outlet.
2. Carefully guide the drawer into the prepared opening. Avoid pinching the cord between the oven and the wall.
3. Slide the drawer all the way until the mounting
flange is flush with the face of the cabinet.
See Figure 5.
4. Open the drawer. Using the 4 holes on
the drawer as a template , pre drill the cabinet
using a 1/16" bit. See Figure 5.
5. Secure the drawer with the 4 screws supplied.
See Figure 6.
MODEL AND SERIAL NUMBER LOCATION
The name plate includes model and serial number. Open the Microwave Drawer fully. The label is beyond the
back wall of the microwave cavity facing up from the flat surface.
CARE,CLEANING AND MAINTENANCE
Refer to the Operation Manual for cleaning instructions.
4Screws
4S
c rews
Figure 6
4
Figure 5
PN:16170000A93816
Screws
Mounting flange