Forward View Displays FPM-201 User manual

Users Manual
FPM-201 Monitor
Copyright 2011 Forward View Displays 3311 N Kennicott Ave.
http://www.fvdnow.com Arlington Heights, IL 60004
+1.866.688.4035
Getting Familiar with the FPM-201 Monitor
1. User Controls
2. Input/Output Area.
3. OSD (on screen display) explanation.
4. Touch screen use and calibration (on touch screen models)
VESA
Mount
100 x 100 mm
Monitor Front Monitor Rear
User control Navigation keys USB Power VGA DVI
while in OSD mode
Input/Output Area
1. Plug the AC adapter into a suitable, grounded source. Connect the AC adapter to the
Power connector in the Input/Output area accessed at the bottom rear of the monitor.
2. Press the Power button and note the green LED indicator located inside the Power button
itself. If no signal source is connected to either VGA or DVI connector, the LCD backlight
will turn off and the unit will go into Standby, with the Power indicator slowly flashing red.
3. Connect either end of the USB Type A-Type A cable into the USB port of the monitor and
plug the other end into the associated PC. (applicable only for touch versions of the
monitor)
4. Connect either VGA or DVI connectors to the monitor in the Input/Output area and tighten
thejackscrews for the connector. The other end should be connected to a PC with the
capability of providing UXGA (1600 X 1200) resolution for best results.
5. Note that the display is now showing PC content.
6. Proceed to the OSD menu description in the following section.

Users Manual
FPM-201 Monitor
Copyright 2011 Forward View Displays 3311 N Kennicott Ave.
http://www.fvdnow.com Arlington Heights, IL 60004
+1.866.688.4035
3. On Screen Display (OSD) Menu Options
1. To engage the OSD, press the “Menu” button.
2. Move between sections by pressing the “+” and “-“ buttons.
3. To enter any section, press the Menu button.
4. To change the setting, use the “+” and “-“ buttons. Once done, press the Menu button.
5. To exit a section, press the “Auto” button.
Colour Mode
Nominal setting
Contrast 50
Brightness 50
Colour temp 9300 (warm) 6500 (std) User
Colour adjust when Colour Temp is set to “User” only, the
following screen will appear.
Picture Mode
Nominal Setting
H Position 50
V Position 50
Phase 52
Clock 50
Sharpness 3

Users Manual
FPM-201 Monitor
Copyright 2011 Forward View Displays 3311 N Kennicott Ave.
http://www.fvdnow.com Arlington Heights, IL 60004
+1.866.688.4035
Function Mode Function
Auto Adjust select “Yes” to auto correct in VGA
Auto Colour select “Yes” to auto correct in VGA
Phase
OSD Menu Mode Function
Language English French German Spanish
Korean Italian Japanese
Traditional Chinese Portuguese
Simplified Chinese
OSD H Position 0- left 50- center 100- right
OSD V Position 0- bottom 50- center 100- top
OSD Timer On- 15 sec timeout Off- no timeout
Misc Mode Function
Input VGA DVI
Reset Reset all values to factory settings
Volume Not applicable

Users Manual
FPM-201 Monitor
Copyright 2011 Forward View Displays 3311 N Kennicott Ave.
http://www.fvdnow.com Arlington Heights, IL 60004
+1.866.688.4035
4. Touch Screen Calibration
1. Ensure that the Monitor USB cable is connected to the PC.
2. Load the Touch screen controller program onto the PC. The PC will auto-detect the touch
screen during software installation.
3. Run the touch screen calibration program after the driver has been loaded. This is named
“Touchscreen Control Panel v.1.0.0-USB”.
4. The following screen will appear:
Select the named controller and hit
“OK”
Next, the Control Panel screen will
appear. Select “calibrate”
Your display will have an all white
background with this message at the
center. Follow the instructions:
starting at the top center, hit the
precise center of the target square
provided. A pencil eraser is a good
tool for this. Repeat clockwise until
all four squares have been entered.
When the fourth target is entered,
the following message will appear
at the center of the display. Hit “Yes”,
calibration is now complete!