FOS Technologies Ribbon Driver 800 User manual

FOS Ribbon Driver
User’s Manual

INTRODUCTION
Thank you for purchasing this Ribbon Driver 800. The unit is designed for LED strip light. Please read this
user manual carefully before use.
What is included
▪1pc Ribbon Driver 800
▪1pc Power cord ▪1pc User Manual
Safety Instruction
WARNING!!! To reduce the risk of fire, electric shock, or
injury to persons, follow these important safety
instructions:
▪This product is intended for indoor use only!
▪Always turn off, unplug power and allow fixture to cool before servicing.
▪Ensure that fixture is properly grounded.
▪Please keep this User Guide for future consultation.
▪To prevent risk of fire or shock, do not expose fixture to rain or moisture. ▪The unit must be
installed in a location with adequate ventilation, at least 50cm from adjacent surfaces. Be sure no
ventilation slots are blocked.
▪Make sure power cord is never crimped or damaged.
FEATURES
▪Flicker free for film or video
▪4 working modes: DMX, Auto, Sound, Master/Slave
▪5 DMX modes: 3ch, 4ch, 6ch, 12ch, 16ch
▪4 output ports and each port can be addressed individually
▪18 preset colors with linear dimmer
▪6 built-in programs with various speeds
▪3 sound programs with adjustable sound sensitivity
▪16 x 2 digits LCD display
!

SETUP
Mounting
Truss/ceiling /wall mounting are available for this small controller.
IMPORTANT!!! Safety cables must always be used. The safety cable
must be capable of holding 10 times the weight of the fixture.
AC Power
The fixture is designed to work on 110V/230V 50Hz. Before applying power to a unit, check that
the source voltage matches the unit’s requirement.
Connection
Connect the wires of LED strip to terminator of Ribbon Driver correctly base on color code of
wire.
OPERATION INSTRUCTIONS
This fixture offers 4 working modes: DMX, Auto, Sound and M/S.
1. Connect the fixtures to main power supply.
2. Turn on power switch and LED indication on Control Panel is lit up.
3. Wait for some seconds till system is ready.
4. Press buttons to continue.

Menu Map
►System Setup [new software]
This mode is designed for factory to upload software through USB port. Your product has been tested
before shipment. Just check local distributor’s web site if updated software is available.
►System Mode [ xxx ]
Press MENU button till display reads “System Mode [XXX]”, then use UP/DOWN button to scroll
through” DMX, Slave, Auto, Sound.
►DMX Mode
The unit can be operated in 3ch, 4ch or 6ch. Set DMX address according to the DMX mode selected.
►Master/Slave Mode
For large venue, multiple systems can be run in sync as Master/Slave. Use DMX cables to link the
Drivers together.
1. One of Ribbon Driver 4 in the daisy chain is to be set as Master and this Master must work under Auto
or Sound mode.
2. Other drivers are to be set in Slave mode.
3. Operate the Master Driver in Auto and Sound mode to run the whole system.

Technical Specifications
Power Input: AC110V/230V 50-60Hz
Output voltage: DC 12V or 24V Load: 200W/port, total
800W max.
Fuse: F5A/250V
Dimension: 436*235*62 mm
Weight: 5.5 kg
I
MPORTANT INFORMATION!
In order to optimize the recovery and recycling of the materials that
old appliances contain and reduce the impact on human health and
the environment, ensure that this product is recycled at the end of its
life.
DMX mode 1: 3 Channels
DMX mode 2: 4 Channels
Channel
Value
Function
1
0-255
Red Intensity 0-100%
2
0-255
Green Intensity 0-100%
3
0-255
Blue Intensity 0-100%
Channel
Value
Function
1
0-152
Master dimmer 0-100%
152-242
Strobe from slow to fast
243-255
Open
2
0-255
Red Intensity 0-100%
3
0-255
Green Intensity 0-100%
4
0-255
Blue Intensity 0-100%

DMX mode 3: 6 Channels
DMX mode 4: 12 Channels
Channel
Value
Function
1
0-255
Red Intensity 0-100%
2
0-255
Green Intensity 0-100%
3
0-255
Blue Intensity 0-100%
4
0-255
Strobe from slow to fast
5
0-001
002-255
No function
Built-in programs
6
0-255
Master dimmer 0-100%
Channel
Value
Function
1
0-255
Port 1 Red Intensity 0-100%
2
0-255
Port 1 Green Intensity 0-
100%
3
0-255
Port 1 Blue Intensity 0-100%
10
0-255
Port 4 Red Intensity 0-100%
11
0-255
Port 4 Green Intensity 0-
100%
12
0-255 Port 4 Blue Intensity 0-100%

DMX mode 5: 16 channels
Channel
Value
Function
1
0-152
Port 1 Master dimmer 0-
100%
152-242
Port 1 Strobe from slow to
fast
243-255
Port 1 Open
2
0-255
Port 1 Red Intensity 0-100%
3
0-255
Port 1 Green Intensity 0-
100%
4
0-255
Port 1 Blue Intensity 0-
100%
13
0-152
Port 4 Master dimmer 0-
100%
152-242
Port 4 Strobe from slow to
fast
243-255
Port 4 Open
14
0-255
Port 4 Red Intensity 0-100%
15
0-255
Port 4 Green Intensity 0-
100%
16
0-255
Port 4 Blue Intensity 0-
100%