Foscam 305503000664 User manual

Video Doorbell
V1.2
305503000664
User Manual • Uživatelský manuál •
Užívateľský manuál • Használati utasítás •
Benutzerhandbuch

2
Dear customer,
The user manual for the product contains the product functions, method of use and
operating procedure. Read the user manual carefully to get the best experience and
avoid unnecessary damage. Keep the manual for future reference.
WARNING
Do not use the product in violation of local laws and regulations. A user who violates
local laws and ordinances will be held responsible for all consequences of purchasing
and using the product.
Alza.cz a.s. is not responsible for any violation of local laws and regulations by the user.
✉www.alza.co.uk/kontakt
✆[phone]
Importer Alza.cz a.s., Jankovcova 1522/53, Holešovice, 170 00 Praha 7, www.alza.cz

3
What is in the Box
2. Physical Description
Front Panel
Light sensor
1 x Mounting bracket
Doorbell button
Camera
Microphone
1 x Video Doorbell
1 x Power Kit
1 x Silicone Plug
1 x 5°Vertical angle bracket
1 x Thick mounting bracket
2 x Wire Extenders
2 x Wire Nuts
1 x Drill Hole
Position Template
1 x Quick Setup Guide
1 x 15°Horizontal angle
bracket
1 x Type-C cable
1 x Dual-purpose
screwdriver
1 x Expansion Screws

4
Rear Panel
Bottom Panel
Add device: Connection via Foscam App (Recommended)
It is strongly recommended that you complete the “add devices” process on the Foscam
app before the doorbell hardware is installed.
Before you get started
Scan the QR code below to download and install the Foscam APP; and learn how to add
the doorbell to the APP:
Download the APP APP add doorbell instruction video
To ensure a smoother video experience on your smart phone, it is recommended that
you smart phone meet the following specifications:
•iOS: version 11 or higher.
•Android: 4.1 or higher, using a device with Graphics Processing Unit (GPU)
NOTE: For the best experience, please update the APP to the latest version!
Speaker
Reset
Mounting
Slot
Micro SD Card Slot
Power Input Port
Type-C Port
Security screw hole

5
Wi-Fi connection
1. Plug the smaller end of the USB cable into the Type-C port on the back of the Video
Doorbell, and the larger end into a USB wall charger such as your smart phone charger
(DC5V 1.0A power output recommended for faster charging). Please wait for a few
seconds until you hear “Ready for Wi-Fi configuration”.
Please note that it is forbidden to connect the doorbell to AC and Type-C supply at
the same time.
TIPS: If you did not hear the voice prompt, press and hold reset for about 10 seconds to
reset the camera.
2. Make sure that your smart phone is connected to your Wi-Fi router.
TIPS: The camera supports dual-band 2.4GHz and 5GHz Wi-Fi networks, so you can
choose the channel with the stronger signal to use. For example SSID: XXXXX_2.4G or
XXXXX_5G.
3. Open the foscam APP and please register a Foscam account, or sign in if you have one
already.
4. After logging into Foscam APP, select “Tap to add a camera” or “+” icon on the upper
right corner, then select “Scan the QR code” and scan the QR code that labeled at the
bottom of your camera.
Tap + icon select “Scan the code” Scan the QR code
which is located at the
bottom of your camera.

6
5. In “Add Device”, if you hear “Hello Foscam”, select the checkbox and tap “Next”,
continue to confirm that the device is in the blue flashing state and tap “Next”. In “Wi-Fi
connection”, enters your Wi-Fi’s password and tap “Confirm”.
6. Please scan the QR code on the doorbell with the smart phone camera, then you will
hear a voice prompt say “Wi-Fi connecting”. Select the checkbox and tap “Next”.
TIPS: Please place the QR code on the phone screen about 10-15cm (3.94 to 5.9in) away,
and if you encounter difficulties you can try to move the screen slowly around 10-15cm
(3.94 to 5.9in).
7. Wait a few seconds until the camera notifies you that the “Wireless connection
succeeded” which means your camera has connected to your Wi-Fi successfully. After,
you can set the camera name and tap “Save” in “Set name” interface.
Heard „Hello Focam!
And tap „Next“
Confirm device
flashes blue
Enter you Wi-Fi
password and tap
„Confirm“
Camera added
successfully and
name has been set
Confirm device white
light flashes

7
NOTE: If the adding process fails, please reset your camera and try adding according to
the above method.
Reset
8. In “Select Chime Type”, tap “Select Chime Type”, and tap “Next”. In “Select Chime
Type”, select Chime type and tap “Mechanical chime” or “Digital chime” or “None” (Please
select the type of your existing chime).
Tap Select Chime Type Select the type of your existing chime
NOTE: Please carefully confirm the existing chime type in your home. If the chime type is
selected incorrectly, the transformer and chime at home will be damaged, causing the
doorbell and chime to not work properly. Generally, a mechanical chime refers to the
ringing sound made by striking a metal with a metal striker, while digital chime refers to
the ringing sound made by playing music through a speaker.
If you are still not sure, please watch the chime type description video carefully, or
consult our customer service staff.

8
9. Tapping on the play button in the video box will jump to the “Camera Login” setting
interface. For your security, please set a new username and password for your camera
before viewing live video.
Tap Set a new username
and password
10. After completing the above steps, you can begin installing your camera.
Video Doorbell Installation
NOTE:
•Make sure you have installed the Foscam APP, and have scanned the doorbell QR
code and completed the “add device” process in the app before beginning the
hardware installation process.
•If you choose to use AC power the video doorbell, you need to ensure that the
specification of the transformer in your home is 8V~24V AC, the minimum power
requirement is 8VA.
•If you use DC power to power the video doorbell, you need to prepare a DC
12V~30V power adapter, the minimum power requirement is 6W.
•If you use Type-C interface to power the video doorbell, you need to prepare a
DC5/15A power adapter, the minimum power requirement is 5W.
STEP 1
Ring the existing doorbell, make sure it is working and locate the place of your existing
chimes in the house.

9
STEP 2
Shut off the master circuit breaker in your house. Turn the lights in your home on / off
to make sure the electricity in your house is properly shut off.
If you are comfortable doing it yourself, consult a qualified electrician.
STEP 3
Indoor chimes are generally of two types: mechanical, or digital. If you need to use the
existing mechanical chime or digital chime in your home, please install the Power Kit in
parallel to the chime. Power Kit is generally used to solve the problem of abnormal
ringing of the chime after the video doorbell replaces the traditional doorbell buttons.
How to distinguish between Digital Chime and mechanical Chime, please scan the
following QR code to view.
What is required: Dual-purpose screwdriver

10
After removing the cover of the mechanical chime or digital chime, use the wire
connection terminal with the Power Kit as pictured. After wiring is completed, replace
the cover.
Bypass Model:
If you do not want to use the existing chime, you can switch the cable on the Power kit
to the bypass interface, and then connect it in parallel to the existing chime This will
short-circuit the chime at our home. You can choose to add Wi-Fi chime, realize the
function of chime. If you choose to use the Power Kit by pass mode, be sure to set the
chime type to “None” in you APP to avoid damaging the transformer.
You can scan the QR code below to search and watch the power kit installation video.
Remove the cover
Replace the cover

11
STEP 4:
Remove the existing doorbell button near the front door. Pull the two wires out carefully
when removing the old doorbell. Straighten the wire end if necessary.
What is required: Dual-purpose screwdriver
STEP 5:
Determine the mounting position of the doorbell. First check if you can reuse the
existing holes in the wall. Use the drill hole position template to mark the screw holes in
the area where the existing doorbell button was located. Place the drill hole position
template at least 1.5m (59”) high from the ground to ensure that the height of the
installed doorbell will be suitable, and then drill the holes (use PH2 drill bit).

12
STEP 6:
Use the provided wall anchors if installing in materials such as stucco, brick, or concrete.
If installing into a wooden doorframe, there is no need to use the wall anchors.
STEP 7:
Optional: Use the 15° mounting bracket or 5°mouting bracket as a supplementary
mounting bracket if you wish to adjust the doorbell camera’s field of view to cover more
of one side.

13
STEP 8:
Lead the existing doorbell wires through the central square hole on the bracket before
you start mounting.
Insert the two provided screws through the screw holes, or through the 5°Vertical angle
bracket / 15°Horizontal angle bracket / Thick mounting bracket, (install the mounting
bracket to the 5° Vertical angle bracket / 15°Horizontal angle bracket), and fasten the
screws tightly.
What is required: Mounting Bracket ( Screw Packs / 5°Vertical angle bracket (Optional) /
15°Horizontal angle bracket (optional) / Dual-purpose screwdriver.
Optional Install A Optional Install B Optional Install C
Without angle bracket With 5°Vertical angle bracket With 15°Horizontal angle
Bracket
Mounting Screws
Mounting Screws
Mounting Screws

14
Optional Install D Optional Install E
STEP 9:
Connect the wires to the two terminals at the back of the doorbell, and then tighten the
terminal screws. Wire can connect to any terminal as the electric current is alternating
current.
NOTE: To prevent short-circuit; make sure the wires are not touching each other after
connecting them to the terminals. If the wires are too short, use the extension wires and
wire nuts provided to make them longer. Use electrical wiring tape to secure the
connection if the wall does not have space for wire nuts.
What are required: Extension Wires and Wire Nuts (Optional) / Video doorbell / Philips-
Head Screwdriver.
Mounting Screws
Mounting Screws
With 5°Vertical angle
briket and 15 °Horizontal
angle bracket
With Thick mounting briket
This installation method can
be used for Type-C cable for
DC power supply

15
Please note that it is forbidden to connect the doorbell to AC and Type-C power
supply at the same time.
STEP 10:
Hook the doorbell on top of the mounting bracket and then snap the doorbell bottom to
the bracket. You may hear a “click” sound.
STEP 11:
Switch the master circuit breaker in your house back to ON.

16
STEP 12:
Press the doorbell to test the chime connection.
Did your doorbell chime? If yes, it is working! If no, check that wires are secure.
Open the foscam APP again and check if you can view live video.
If not, please remove the doorbell and press the reset button to re-add it in the app.
STEP 13:
Use the included screwdriver to tighten the anti-theft screw.
What is required: Dual-purpose screwdriver.

17
Other ways to access your camera
•Foscam VMS
Foscam VMS is a new tool for PCs. It does not require plug-in and is compatible with
Windows & Mac, supporting all Foscam HD cameras and up to 36 cameras at the same
time. If you would like to manage multiple cameras, we suggest you install Foscam VMS.
You can download the “Foscam VMS” Windows version from foscam.com/vms, and can
download the “Foscam VMS” Mac version from the APP store:
https://apps.apple.com/cn/app/foscamvms/id1521202507?mt=12.
NOTE: For the best experience, please update Foscam VMS to the latest version!
Add the IP Camera
1. Run Foscam VMS, then create a local administrator account and login.
2. Tap the “+” icon on the Foscam VMS and follow the setup wizard to add your camera.
Please visit foscam.com/downloads to view the user manual and for additional detailed
steps.

18
Important Notice
•Doorbell Username & Password
The doorbell username & password are used to access and manage your camera.
Having a strong can significantly improve the security of your doorbell.
If you have forgotten either of them, please press the “Reset” button and hold it for
more than 10 seconds while the doorbell is powered on. After release the button. The
camera will automatically reboot and the default settings will be restored.
You can then reconnect the camera by following this Quick Setup Guide.
•Foscam Cloud Service Account Username & Password
Your Foscam Cloud service account and password may be used to access both the
Foscam App and then Foscam Cloud service website. Therefore, you can register your
account username & password on either one.
•Storage Media
You camera supports cloud, NVR (Network Video Recorder), and Micro SD card (only
supports FAT-32 format) storage formats. If you wish to record and play back large
amounts of video, we recommend using a Foscam NVR device as well.
•Firmware Upgrade
You can upgrade the firmware of your camera with the Foscam App by using the new
“One-Key Online Upgrade” feature (Open the Foscam App and Login to the camera,
select Settings > Firmware Upgrade).
You also can download the latest version to upgrade your camera from our official
website foscam.com/upgrades.

19
•Safety Tips
Please ensure that the proper power supply is used before using the camera.
Please install the doorbell and bracket securely using the screw provided.
Please use this product within the temperature range. When the ambient temperature is
too high or too low, it may cause product failure.
To avoid the risk of fire or electric shock, please keep your camera connectors in a cool,
dry place.
Please keep the doorbell out of reach of small children.
This product is not a toy; children should use the product under adult supervision.
Change your default port to a greater range to help ensure the safety of your
connection. How to change the default port: please visit foscam.com/downloads to view
the user manual.
Check the logs of your Foscam cameras frequently. Foscam Cameras have embedded
logs reminding telling you which IP addresses are accessing the camera.
7. Product Performance
WLAN frequency range: 2412MHz –2472MHz and 5725MHz –5850MHz
Maximum transmission power: < 16dBm
Wireless Standard: IEEE802.11b/g/n (2.4GHz)
IEEE802.11a/n/ac (5GHz)
Power supply: DC 5V 1.0A 5W or AC 8~24V
8. Technical Support
If you have problems with your Foscam device, please contact the reseller you
purchased from, or you can e-mail the headquarters technical support team:
[e-mail].
Your valuable comments and suggestions on improving Foscam products are welcomed!

20
Warranty Conditions
A new product purchased in the Alza.cz sales network is guaranteed for 2 years. If you
need repair or other services during the warranty period, contact the product seller
directly, you must provide the original proof of purchase with the date of purchase.
The following are considered to be a conflict with the warranty conditions, for
which the claimed claim may not be recognized:
•Using the product for any purpose other than that for which the product is intended
or failing to follow the instructions for maintenance, operation and service of the
product.
•Damage to the product by a natural disaster, the intervention of an unauthorized
person or mechanically through the fault of the buyer (e.g. during transport, cleaning
by inappropriate means, etc.).
•Natural wear and aging of consumables or components during use (such as
batteries, etc.).
•Exposure to adverse external influences, such as sunlight and other radiation or
electromagnetic fields, fluid intrusion, object intrusion, mains overvoltage,
electrostatic discharge voltage (including lightning), faulty supply or input voltage and
inappropriate polarity of this voltage, chemical processes such as used power
supplies, etc.
•If anyone has made modifications, modifications, alterations to the design or
adaptation to change or extend the functions of the product compared to the
purchased design or use of non-original components.