Foscam WD-R1200U User manual
2.4G
5G
LED Descriptions
V1.3
WiFi Extender
Getting Started
Power on
Plug the extender into a power outlet that is within 2 meters (6.56
feet) of your router. Wait until the 2.4G and 5G LED lights turn solid
green. If anything goes wrong, please press and hold the "Reset"
button on the side of the extender for more than 8 seconds (if the
reset process fails, please contact the seller).
Set UP
Method 1: Mobile Phone Setup
Please ensure that your phone
has successfully connected to
the extender's WiFi network
name (wi-2.4G-XXXX or
wi-5G-XXXX) before
launching the phone browser.
3. Enter the default password: admin (must be lower case).
4. Select your home WiFi network name (SSID) you want to extend.
5. Enter the password of your home WiFi network.
6. Set your extender’s new WiFi network name (SSID) and password.
The default SSID of the extender
(Foscam_6-pro-2.4G
and Foscam_6-pro-5G) can be
changed. The default password
can also be changed (the default
password is your router's WiFi
network password).
2.4G
5G
1
2
1. Turn o your mobile data, then connect your mobile phone to
the extender's WiFi network name (SSID): wi-5G-XXXX or
wi-2.4G-XXXX (‘XXXX’ is the last 4 letters of the MAC Address
that is labeled on the back of the extender).
TP-LINK_BFF5
Foscam_1
Foscam_2
Foscam_3
Foscam_4
Foscam_5
Foscam_6
Foscam_7
Foscam_6
Foscam_7
Foscam_8
Foscam_9
7. Please check your extender's WiFi network name (SSID) and
password. If they are correct, click Start Connect and wait 30-60s.
Foscam_6
Foscam_6-pro-2.4G
Foscam_6-pro-5G
Method 2: PC Setup
2. Launch a web browser (Chrome/Firefox/Safari) and enter
192.168.188.1 in the address bar.
You can also connect your computer and extender with an
ethernet cable, then launch a web browser and enter
192.168.188.1 to congure your extender.
Note: If the login page does not appear, try another web browser
and attempt conguration once more. If the above method fails,
you can also try resetting the extender before attempting to
congure it again.
1. Connect your computer to the extender's WiFi network name
(SSID): wi-5G-XXXX or wi-2.4G-XXXX (‘XXXX’ is the last
4 letters of the MAC Address that is labeled on the back of the
extender).
Foscam_1
Foscam_2
Foscam_3
Foscam_4
Foscam_5
This device increases your WiFi signal coverage
(not the speed, which is determined by your internet
service provider).
Reset 8. After setup is completed, please view the rst three indicator
lights. If they are solid green, that indicates the conguration
process was successful. If the lights are not on, please reset the
extender and attempt conguration once more. To surf the web,
please connect your devices to your extender's WiFi network
name (SSID) which was set in Step 6.
Reset /WPS
Turn o your
mobile data
Settings Wi-Fi
Wi-Fi
Extender
Extender
Foscam_6-pro-2.4G
Foscam_6-pro-5G
Extender
The default extender name is XXXXX-pro can be changed.
Foscam_6
Please enter the password of your home WiFi network.
Extender
Extender
LED
Status
Indication(For Extender Mode)
Lights 1 and 2 are on: extender is normal.
Light 1 or Light 2 is o: extender is abnormal
Solid Green
O
On/O
On/O
The extender is connected to your router’s
wireless network.
No wireless connection is established.
The Ethernet port is connected to a powered-on
device.
The Ethernet port is connected to a powered-on
device.
2.4G
5G
Ethernet
Ethernet
Signal
Power on
Power o
Press and hold for more than 8 seconds. All lights
will turn o, then the rst and second lights will
turn solidly on, indicating that reset was successful.
Reset/
WPS
Reset
WPS
Press both WPS buttons (the one on your router,
and the one on your extender) for one second.
After about 1 minute, Lights 1 - 3 should turn be
solid green, indicating successful connection.
Choose
wi-2.4G-xxxx or
wi-5G-xxxx
Your home WiFi
network name (SSID)
Extender
Please select your home WiFi network to be extended
2.4G
5G
Signal
Ethernet
Ethernet
Light 1
Light 2
Light 3
Light 4
Light 5
After conguration is
completed, if you want to
change your extender's WiFi
network name or password,
"you must reset your extender
and perform the conguration
process again.
192.168.188.1
2. Launch a phone browser (e.g. Chrome/Firefox/Safari) and enter
192.168.188.1 in the address bar.
Note: If the login window does not appear, you need rstly to check
"your mobile data settings: if mobile data is enabled, please toggle
your mobile data to o and recongure one more time. If the above
method fails, please try resetting your extender and attempting the
conguration process once again.
Model: WD-R1200U
wifi-2.4G-xxxx
wifi-5G-xxxx
wifi-2.4G-XXXX
wifi-5G-XXXX
Setup Guide Video
FAQ
Foscam, Inc.
Website:https: www.foscam.com/faqs/view.html?id=256
2.4G
5G
LED Descriptions
V1.3
WiFi Extender
Getting Started
Power on
Plug the extender into a power outlet that is within 2 meters (6.56
feet) of your router. Wait until the 2.4G and 5G LED lights turn solid
green. If anything goes wrong, please press and hold the "Reset"
button on the side of the extender for more than 8 seconds (if the
reset process fails, please contact the seller).
Set UP
Method 1: Mobile Phone Setup
Please ensure that your phone
has successfully connected to
the extender's WiFi network
name (wi-2.4G-XXXX or
wi-5G-XXXX) before
launching the phone browser.
3. Enter the default password: admin (must be lower case).
4. Select your home WiFi network name (SSID) you want to extend.
5. Enter the password of your home WiFi network.
6. Set your extender’s new WiFi network name (SSID) and password.
The default SSID of the extender
(Foscam_6-pro-2.4G
and Foscam_6-pro-5G) can be
changed. The default password
can also be changed (the default
password is your router's WiFi
network password).
2.4G
5G
1
2
1. Turn o your mobile data, then connect your mobile phone to
the extender's WiFi network name (SSID): wi-5G-XXXX or
wi-2.4G-XXXX (‘XXXX’ is the last 4 letters of the MAC Address
that is labeled on the back of the extender).
TP-LINK_BFF5
Foscam_1
Foscam_2
Foscam_3
Foscam_4
Foscam_5
Foscam_6
Foscam_7
Foscam_6
Foscam_7
Foscam_8
Foscam_9
7. Please check your extender's WiFi network name (SSID) and
password. If they are correct, click Start Connect and wait 30-60s.
Foscam_6
Foscam_6-pro-2.4G
Foscam_6-pro-5G
Method 2: PC Setup
2. Launch a web browser (Chrome/Firefox/Safari) and enter
192.168.188.1 in the address bar.
You can also connect your computer and extender with an
ethernet cable, then launch a web browser and enter
192.168.188.1 to congure your extender.
Note: If the login page does not appear, try another web browser
and attempt conguration once more. If the above method fails,
you can also try resetting the extender before attempting to
congure it again.
1. Connect your computer to the extender's WiFi network name
(SSID): wi-5G-XXXX or wi-2.4G-XXXX (‘XXXX’ is the last
4 letters of the MAC Address that is labeled on the back of the
extender).
Foscam_1
Foscam_2
Foscam_3
Foscam_4
Foscam_5
This device increases your WiFi signal coverage
(not the speed, which is determined by your internet
service provider).
Reset 8. After setup is completed, please view the rst three indicator
lights. If they are solid green, that indicates the conguration
process was successful. If the lights are not on, please reset the
extender and attempt conguration once more. To surf the web,
please connect your devices to your extender's WiFi network
name (SSID) which was set in Step 6.
Reset /WPS
Turn o your
mobile data
Settings Wi-Fi
Wi-Fi
Extender
Extender
Foscam_6-pro-2.4G
Foscam_6-pro-5G
Extender
The default extender name is XXXXX-pro can be changed.
Foscam_6
Please enter the password of your home WiFi network.
Extender
Extender
LED
Status
Indication(For Extender Mode)
Lights 1 and 2 are on: extender is normal.
Light 1 or Light 2 is o: extender is abnormal
Solid Green
O
On/O
On/O
The extender is connected to your router’s
wireless network.
No wireless connection is established.
The Ethernet port is connected to a powered-on
device.
The Ethernet port is connected to a powered-on
device.
2.4G
5G
Ethernet
Ethernet
Signal
Power on
Power o
Press and hold for more than 8 seconds. All lights
will turn o, then the rst and second lights will
turn solidly on, indicating that reset was successful.
Reset/
WPS
Reset
WPS
Press both WPS buttons (the one on your router,
and the one on your extender) for one second.
After about 1 minute, Lights 1 - 3 should turn be
solid green, indicating successful connection.
Choose
wi-2.4G-xxxx or
wi-5G-xxxx
Your home WiFi
network name (SSID)
Extender
Please select your home WiFi network to be extended
2.4G
5G
Signal
Ethernet
Ethernet
Light 1
Light 2
Light 3
Light 4
Light 5
After conguration is
completed, if you want to
change your extender's WiFi
network name or password,
"you must reset your extender
and perform the conguration
process again.
192.168.188.1
2. Launch a phone browser (e.g. Chrome/Firefox/Safari) and enter
192.168.188.1 in the address bar.
Note: If the login window does not appear, you need rstly to check
"your mobile data settings: if mobile data is enabled, please toggle
your mobile data to o and recongure one more time. If the above
method fails, please try resetting your extender and attempting the
conguration process once again.
Model: WD-R1200U
wifi-2.4G-xxxx
wifi-5G-xxxx
wifi-2.4G-XXXX
wifi-5G-XXXX
Setup Guide Video
FAQ
Foscam, Inc.
Website:https: www.foscam.com/faqs/view.html?id=256
2.4G
5G
LED Descriptions
V1.3
WiFi Extender
Getting Started
Power on
Plug the extender into a power outlet that is within 2 meters (6.56
feet) of your router. Wait until the 2.4G and 5G LED lights turn solid
green. If anything goes wrong, please press and hold the "Reset"
button on the side of the extender for more than 8 seconds (if the
reset process fails, please contact the seller).
Set UP
Method 1: Mobile Phone Setup
Please ensure that your phone
has successfully connected to
the extender's WiFi network
name (wi-2.4G-XXXX or
wi-5G-XXXX) before
launching the phone browser.
3. Enter the default password: admin (must be lower case).
4. Select your home WiFi network name (SSID) you want to extend.
5. Enter the password of your home WiFi network.
6. Set your extender’s new WiFi network name (SSID) and password.
The default SSID of the extender
(Foscam_6-pro-2.4G
and Foscam_6-pro-5G) can be
changed. The default password
can also be changed (the default
password is your router's WiFi
network password).
2.4G
5G
1
2
1. Turn o your mobile data, then connect your mobile phone to
the extender's WiFi network name (SSID): wi-5G-XXXX or
wi-2.4G-XXXX (‘XXXX’ is the last 4 letters of the MAC Address
that is labeled on the back of the extender).
TP-LINK_BFF5
Foscam_1
Foscam_2
Foscam_3
Foscam_4
Foscam_5
Foscam_6
Foscam_7
Foscam_6
Foscam_7
Foscam_8
Foscam_9
7. Please check your extender's WiFi network name (SSID) and
password. If they are correct, click Start Connect and wait 30-60s.
Foscam_6
Foscam_6-pro-2.4G
Foscam_6-pro-5G
Method 2: PC Setup
2. Launch a web browser (Chrome/Firefox/Safari) and enter
192.168.188.1 in the address bar.
You can also connect your computer and extender with an
ethernet cable, then launch a web browser and enter
192.168.188.1 to congure your extender.
Note: If the login page does not appear, try another web browser
and attempt conguration once more. If the above method fails,
you can also try resetting the extender before attempting to
congure it again.
1. Connect your computer to the extender's WiFi network name
(SSID): wi-5G-XXXX or wi-2.4G-XXXX (‘XXXX’ is the last
4 letters of the MAC Address that is labeled on the back of the
extender).
Foscam_1
Foscam_2
Foscam_3
Foscam_4
Foscam_5
This device increases your WiFi signal coverage
(not the speed, which is determined by your internet
service provider).
Reset 8. After setup is completed, please view the rst three indicator
lights. If they are solid green, that indicates the conguration
process was successful. If the lights are not on, please reset the
extender and attempt conguration once more. To surf the web,
please connect your devices to your extender's WiFi network
name (SSID) which was set in Step 6.
Reset /WPS
Turn o your
mobile data
Settings Wi-Fi
Wi-Fi
Extender
Extender
Foscam_6-pro-2.4G
Foscam_6-pro-5G
Extender
The default extender name is XXXXX-pro can be changed.
Foscam_6
Please enter the password of your home WiFi network.
Extender
Extender
LED
Status
Indication(For Extender Mode)
Lights 1 and 2 are on: extender is normal.
Light 1 or Light 2 is o: extender is abnormal
Solid Green
O
On/O
On/O
The extender is connected to your router’s
wireless network.
No wireless connection is established.
The Ethernet port is connected to a powered-on
device.
The Ethernet port is connected to a powered-on
device.
2.4G
5G
Ethernet
Ethernet
Signal
Power on
Power o
Press and hold for more than 8 seconds. All lights
will turn o, then the rst and second lights will
turn solidly on, indicating that reset was successful.
Reset/
WPS
Reset
WPS
Press both WPS buttons (the one on your router,
and the one on your extender) for one second.
After about 1 minute, Lights 1 - 3 should turn be
solid green, indicating successful connection.
Choose
wi-2.4G-xxxx or
wi-5G-xxxx
Your home WiFi
network name (SSID)
Extender
Please select your home WiFi network to be extended
2.4G
5G
Signal
Ethernet
Ethernet
Light 1
Light 2
Light 3
Light 4
Light 5
After conguration is
completed, if you want to
change your extender's WiFi
network name or password,
"you must reset your extender
and perform the conguration
process again.
192.168.188.1
2. Launch a phone browser (e.g. Chrome/Firefox/Safari) and enter
192.168.188.1 in the address bar.
Note: If the login window does not appear, you need rstly to check
"your mobile data settings: if mobile data is enabled, please toggle
your mobile data to o and recongure one more time. If the above
method fails, please try resetting your extender and attempting the
conguration process once again.
Model: WD-R1200U
wifi-2.4G-xxxx
wifi-5G-xxxx
wifi-2.4G-XXXX
wifi-5G-XXXX
Setup Guide Video
FAQ
Foscam, Inc.
Website:https: www.foscam.com/faqs/view.html?id=256
2.4G
5G
LED Descriptions
V1.3
WiFi Extender
Getting Started
Power on
Plug the extender into a power outlet that is within 2 meters (6.56
feet) of your router. Wait until the 2.4G and 5G LED lights turn solid
green. If anything goes wrong, please press and hold the "Reset"
button on the side of the extender for more than 8 seconds (if the
reset process fails, please contact the seller).
Set UP
Method 1: Mobile Phone Setup
Please ensure that your phone
has successfully connected to
the extender's WiFi network
name (wi-2.4G-XXXX or
wi-5G-XXXX) before
launching the phone browser.
3. Enter the default password: admin (must be lower case).
4. Select your home WiFi network name (SSID) you want to extend.
5. Enter the password of your home WiFi network.
6. Set your extender’s new WiFi network name (SSID) and password.
The default SSID of the extender
(Foscam_6-pro-2.4G
and Foscam_6-pro-5G) can be
changed. The default password
can also be changed (the default
password is your router's WiFi
network password).
2.4G
5G
1
2
1. Turn o your mobile data, then connect your mobile phone to
the extender's WiFi network name (SSID): wi-5G-XXXX or
wi-2.4G-XXXX (‘XXXX’ is the last 4 letters of the MAC Address
that is labeled on the back of the extender).
TP-LINK_BFF5
Foscam_1
Foscam_2
Foscam_3
Foscam_4
Foscam_5
Foscam_6
Foscam_7
Foscam_6
Foscam_7
Foscam_8
Foscam_9
7. Please check your extender's WiFi network name (SSID) and
password. If they are correct, click Start Connect and wait 30-60s.
Foscam_6
Foscam_6-pro-2.4G
Foscam_6-pro-5G
Method 2: PC Setup
2. Launch a web browser (Chrome/Firefox/Safari) and enter
192.168.188.1 in the address bar.
You can also connect your computer and extender with an
ethernet cable, then launch a web browser and enter
192.168.188.1 to congure your extender.
Note: If the login page does not appear, try another web browser
and attempt conguration once more. If the above method fails,
you can also try resetting the extender before attempting to
congure it again.
1. Connect your computer to the extender's WiFi network name
(SSID): wi-5G-XXXX or wi-2.4G-XXXX (‘XXXX’ is the last
4 letters of the MAC Address that is labeled on the back of the
extender).
Foscam_1
Foscam_2
Foscam_3
Foscam_4
Foscam_5
This device increases your WiFi signal coverage
(not the speed, which is determined by your internet
service provider).
Reset 8. After setup is completed, please view the rst three indicator
lights. If they are solid green, that indicates the conguration
process was successful. If the lights are not on, please reset the
extender and attempt conguration once more. To surf the web,
please connect your devices to your extender's WiFi network
name (SSID) which was set in Step 6.
Reset /WPS
Turn o your
mobile data
Settings Wi-Fi
Wi-Fi
Extender
Extender
Foscam_6-pro-2.4G
Foscam_6-pro-5G
Extender
The default extender name is XXXXX-pro can be changed.
Foscam_6
Please enter the password of your home WiFi network.
Extender
Extender
LED
Status
Indication(For Extender Mode)
Lights 1 and 2 are on: extender is normal.
Light 1 or Light 2 is o: extender is abnormal
Solid Green
O
On/O
On/O
The extender is connected to your router’s
wireless network.
No wireless connection is established.
The Ethernet port is connected to a powered-on
device.
The Ethernet port is connected to a powered-on
device.
2.4G
5G
Ethernet
Ethernet
Signal
Power on
Power o
Press and hold for more than 8 seconds. All lights
will turn o, then the rst and second lights will
turn solidly on, indicating that reset was successful.
Reset/
WPS
Reset
WPS
Press both WPS buttons (the one on your router,
and the one on your extender) for one second.
After about 1 minute, Lights 1 - 3 should turn be
solid green, indicating successful connection.
Choose
wi-2.4G-xxxx or
wi-5G-xxxx
Your home WiFi
network name (SSID)
Extender
Please select your home WiFi network to be extended
2.4G
5G
Signal
Ethernet
Ethernet
Light 1
Light 2
Light 3
Light 4
Light 5
After conguration is
completed, if you want to
change your extender's WiFi
network name or password,
"you must reset your extender
and perform the conguration
process again.
192.168.188.1
2. Launch a phone browser (e.g. Chrome/Firefox/Safari) and enter
192.168.188.1 in the address bar.
Note: If the login window does not appear, you need rstly to check
"your mobile data settings: if mobile data is enabled, please toggle
your mobile data to o and recongure one more time. If the above
method fails, please try resetting your extender and attempting the
conguration process once again.
Model: WD-R1200U
wifi-2.4G-xxxx
wifi-5G-xxxx
wifi-2.4G-XXXX
wifi-5G-XXXX
Setup Guide Video
FAQ
Foscam, Inc.
Website:https: www.foscam.com/faqs/view.html?id=256
2.4G
5G
LED Descriptions
V1.3
WiFi Extender
Getting Started
Power on
Plug the extender into a power outlet that is within 2 meters (6.56
feet) of your router. Wait until the 2.4G and 5G LED lights turn solid
green. If anything goes wrong, please press and hold the "Reset"
button on the side of the extender for more than 8 seconds (if the
reset process fails, please contact the seller).
Set UP
Method 1: Mobile Phone Setup
Please ensure that your phone
has successfully connected to
the extender's WiFi network
name (wi-2.4G-XXXX or
wi-5G-XXXX) before
launching the phone browser.
3. Enter the default password: admin (must be lower case).
4. Select your home WiFi network name (SSID) you want to extend.
5. Enter the password of your home WiFi network.
6. Set your extender’s new WiFi network name (SSID) and password.
The default SSID of the extender
(Foscam_6-pro-2.4G
and Foscam_6-pro-5G) can be
changed. The default password
can also be changed (the default
password is your router's WiFi
network password).
2.4G
5G
1
2
1. Turn o your mobile data, then connect your mobile phone to
the extender's WiFi network name (SSID): wi-5G-XXXX or
wi-2.4G-XXXX (‘XXXX’ is the last 4 letters of the MAC Address
that is labeled on the back of the extender).
TP-LINK_BFF5
Foscam_1
Foscam_2
Foscam_3
Foscam_4
Foscam_5
Foscam_6
Foscam_7
Foscam_6
Foscam_7
Foscam_8
Foscam_9
7. Please check your extender's WiFi network name (SSID) and
password. If they are correct, click Start Connect and wait 30-60s.
Foscam_6
Foscam_6-pro-2.4G
Foscam_6-pro-5G
Method 2: PC Setup
2. Launch a web browser (Chrome/Firefox/Safari) and enter
192.168.188.1 in the address bar.
You can also connect your computer and extender with an
ethernet cable, then launch a web browser and enter
192.168.188.1 to congure your extender.
Note: If the login page does not appear, try another web browser
and attempt conguration once more. If the above method fails,
you can also try resetting the extender before attempting to
congure it again.
1. Connect your computer to the extender's WiFi network name
(SSID): wi-5G-XXXX or wi-2.4G-XXXX (‘XXXX’ is the last
4 letters of the MAC Address that is labeled on the back of the
extender).
Foscam_1
Foscam_2
Foscam_3
Foscam_4
Foscam_5
This device increases your WiFi signal coverage
(not the speed, which is determined by your internet
service provider).
Reset 8. After setup is completed, please view the rst three indicator
lights. If they are solid green, that indicates the conguration
process was successful. If the lights are not on, please reset the
extender and attempt conguration once more. To surf the web,
please connect your devices to your extender's WiFi network
name (SSID) which was set in Step 6.
Reset /WPS
Turn o your
mobile data
Settings Wi-Fi
Wi-Fi
Extender
Extender
Foscam_6-pro-2.4G
Foscam_6-pro-5G
Extender
The default extender name is XXXXX-pro can be changed.
Foscam_6
Please enter the password of your home WiFi network.
Extender
Extender
LED
Status
Indication(For Extender Mode)
Lights 1 and 2 are on: extender is normal.
Light 1 or Light 2 is o: extender is abnormal
Solid Green
O
On/O
On/O
The extender is connected to your router’s
wireless network.
No wireless connection is established.
The Ethernet port is connected to a powered-on
device.
The Ethernet port is connected to a powered-on
device.
2.4G
5G
Ethernet
Ethernet
Signal
Power on
Power o
Press and hold for more than 8 seconds. All lights
will turn o, then the rst and second lights will
turn solidly on, indicating that reset was successful.
Reset/
WPS
Reset
WPS
Press both WPS buttons (the one on your router,
and the one on your extender) for one second.
After about 1 minute, Lights 1 - 3 should turn be
solid green, indicating successful connection.
Choose
wi-2.4G-xxxx or
wi-5G-xxxx
Your home WiFi
network name (SSID)
Extender
Please select your home WiFi network to be extended
2.4G
5G
Signal
Ethernet
Ethernet
Light 1
Light 2
Light 3
Light 4
Light 5
After conguration is
completed, if you want to
change your extender's WiFi
network name or password,
"you must reset your extender
and perform the conguration
process again.
192.168.188.1
2. Launch a phone browser (e.g. Chrome/Firefox/Safari) and enter
192.168.188.1 in the address bar.
Note: If the login window does not appear, you need rstly to check
"your mobile data settings: if mobile data is enabled, please toggle
your mobile data to o and recongure one more time. If the above
method fails, please try resetting your extender and attempting the
conguration process once again.
Model: WD-R1200U
wifi-2.4G-xxxx
wifi-5G-xxxx
wifi-2.4G-XXXX
wifi-5G-XXXX
Setup Guide Video
FAQ
Foscam, Inc.
Website:https: www.foscam.com/faqs/view.html?id=256
2.4G
5G
LED Descriptions
V1.3
WiFi Extender
Getting Started
Power on
Plug the extender into a power outlet that is within 2 meters (6.56
feet) of your router. Wait until the 2.4G and 5G LED lights turn solid
green. If anything goes wrong, please press and hold the "Reset"
button on the side of the extender for more than 8 seconds (if the
reset process fails, please contact the seller).
Set UP
Method 1: Mobile Phone Setup
Please ensure that your phone
has successfully connected to
the extender's WiFi network
name (wi-2.4G-XXXX or
wi-5G-XXXX) before
launching the phone browser.
3. Enter the default password: admin (must be lower case).
4. Select your home WiFi network name (SSID) you want to extend.
5. Enter the password of your home WiFi network.
6. Set your extender’s new WiFi network name (SSID) and password.
The default SSID of the extender
(Foscam_6-pro-2.4G
and Foscam_6-pro-5G) can be
changed. The default password
can also be changed (the default
password is your router's WiFi
network password).
2.4G
5G
1
2
1. Turn o your mobile data, then connect your mobile phone to
the extender's WiFi network name (SSID): wi-5G-XXXX or
wi-2.4G-XXXX (‘XXXX’ is the last 4 letters of the MAC Address
that is labeled on the back of the extender).
TP-LINK_BFF5
Foscam_1
Foscam_2
Foscam_3
Foscam_4
Foscam_5
Foscam_6
Foscam_7
Foscam_6
Foscam_7
Foscam_8
Foscam_9
7. Please check your extender's WiFi network name (SSID) and
password. If they are correct, click Start Connect and wait 30-60s.
Foscam_6
Foscam_6-pro-2.4G
Foscam_6-pro-5G
Method 2: PC Setup
2. Launch a web browser (Chrome/Firefox/Safari) and enter
192.168.188.1 in the address bar.
You can also connect your computer and extender with an
ethernet cable, then launch a web browser and enter
192.168.188.1 to congure your extender.
Note: If the login page does not appear, try another web browser
and attempt conguration once more. If the above method fails,
you can also try resetting the extender before attempting to
congure it again.
1. Connect your computer to the extender's WiFi network name
(SSID): wi-5G-XXXX or wi-2.4G-XXXX (‘XXXX’ is the last
4 letters of the MAC Address that is labeled on the back of the
extender).
Foscam_1
Foscam_2
Foscam_3
Foscam_4
Foscam_5
This device increases your WiFi signal coverage
(not the speed, which is determined by your internet
service provider).
Reset 8. After setup is completed, please view the rst three indicator
lights. If they are solid green, that indicates the conguration
process was successful. If the lights are not on, please reset the
extender and attempt conguration once more. To surf the web,
please connect your devices to your extender's WiFi network
name (SSID) which was set in Step 6.
Reset /WPS
Turn o your
mobile data
Settings Wi-Fi
Wi-Fi
Extender
Extender
Foscam_6-pro-2.4G
Foscam_6-pro-5G
Extender
The default extender name is XXXXX-pro can be changed.
Foscam_6
Please enter the password of your home WiFi network.
Extender
Extender
LED
Status
Indication(For Extender Mode)
Lights 1 and 2 are on: extender is normal.
Light 1 or Light 2 is o: extender is abnormal
Solid Green
O
On/O
On/O
The extender is connected to your router’s
wireless network.
No wireless connection is established.
The Ethernet port is connected to a powered-on
device.
The Ethernet port is connected to a powered-on
device.
2.4G
5G
Ethernet
Ethernet
Signal
Power on
Power o
Press and hold for more than 8 seconds. All lights
will turn o, then the rst and second lights will
turn solidly on, indicating that reset was successful.
Reset/
WPS
Reset
WPS
Press both WPS buttons (the one on your router,
and the one on your extender) for one second.
After about 1 minute, Lights 1 - 3 should turn be
solid green, indicating successful connection.
Choose
wi-2.4G-xxxx or
wi-5G-xxxx
Your home WiFi
network name (SSID)
Extender
Please select your home WiFi network to be extended
2.4G
5G
Signal
Ethernet
Ethernet
Light 1
Light 2
Light 3
Light 4
Light 5
After conguration is
completed, if you want to
change your extender's WiFi
network name or password,
"you must reset your extender
and perform the conguration
process again.
192.168.188.1
2. Launch a phone browser (e.g. Chrome/Firefox/Safari) and enter
192.168.188.1 in the address bar.
Note: If the login window does not appear, you need rstly to check
"your mobile data settings: if mobile data is enabled, please toggle
your mobile data to o and recongure one more time. If the above
method fails, please try resetting your extender and attempting the
conguration process once again.
Model: WD-R1200U
wifi-2.4G-xxxx
wifi-5G-xxxx
wifi-2.4G-XXXX
wifi-5G-XXXX
Setup Guide Video
FAQ
Foscam, Inc.
Website:https: www.foscam.com/faqs/view.html?id=256
2.4G
5G
LED Descriptions
V1.3
WiFi Extender
Getting Started
Power on
Plug the extender into a power outlet that is within 2 meters (6.56
feet) of your router. Wait until the 2.4G and 5G LED lights turn solid
green. If anything goes wrong, please press and hold the "Reset"
button on the side of the extender for more than 8 seconds (if the
reset process fails, please contact the seller).
Set UP
Method 1: Mobile Phone Setup
Please ensure that your phone
has successfully connected to
the extender's WiFi network
name (wi-2.4G-XXXX or
wi-5G-XXXX) before
launching the phone browser.
3. Enter the default password: admin (must be lower case).
4. Select your home WiFi network name (SSID) you want to extend.
5. Enter the password of your home WiFi network.
6. Set your extender’s new WiFi network name (SSID) and password.
The default SSID of the extender
(Foscam_6-pro-2.4G
and Foscam_6-pro-5G) can be
changed. The default password
can also be changed (the default
password is your router's WiFi
network password).
2.4G
5G
1
2
1. Turn o your mobile data, then connect your mobile phone to
the extender's WiFi network name (SSID): wi-5G-XXXX or
wi-2.4G-XXXX (‘XXXX’ is the last 4 letters of the MAC Address
that is labeled on the back of the extender).
TP-LINK_BFF5
Foscam_1
Foscam_2
Foscam_3
Foscam_4
Foscam_5
Foscam_6
Foscam_7
Foscam_6
Foscam_7
Foscam_8
Foscam_9
7. Please check your extender's WiFi network name (SSID) and
password. If they are correct, click Start Connect and wait 30-60s.
Foscam_6
Foscam_6-pro-2.4G
Foscam_6-pro-5G
Method 2: PC Setup
2. Launch a web browser (Chrome/Firefox/Safari) and enter
192.168.188.1 in the address bar.
You can also connect your computer and extender with an
ethernet cable, then launch a web browser and enter
192.168.188.1 to congure your extender.
Note: If the login page does not appear, try another web browser
and attempt conguration once more. If the above method fails,
you can also try resetting the extender before attempting to
congure it again.
1. Connect your computer to the extender's WiFi network name
(SSID): wi-5G-XXXX or wi-2.4G-XXXX (‘XXXX’ is the last
4 letters of the MAC Address that is labeled on the back of the
extender).
Foscam_1
Foscam_2
Foscam_3
Foscam_4
Foscam_5
This device increases your WiFi signal coverage
(not the speed, which is determined by your internet
service provider).
Reset 8. After setup is completed, please view the rst three indicator
lights. If they are solid green, that indicates the conguration
process was successful. If the lights are not on, please reset the
extender and attempt conguration once more. To surf the web,
please connect your devices to your extender's WiFi network
name (SSID) which was set in Step 6.
Reset /WPS
Turn o your
mobile data
Settings Wi-Fi
Wi-Fi
Extender
Extender
Foscam_6-pro-2.4G
Foscam_6-pro-5G
Extender
The default extender name is XXXXX-pro can be changed.
Foscam_6
Please enter the password of your home WiFi network.
Extender
Extender
LED
Status
Indication(For Extender Mode)
Lights 1 and 2 are on: extender is normal.
Light 1 or Light 2 is o: extender is abnormal
Solid Green
O
On/O
On/O
The extender is connected to your router’s
wireless network.
No wireless connection is established.
The Ethernet port is connected to a powered-on
device.
The Ethernet port is connected to a powered-on
device.
2.4G
5G
Ethernet
Ethernet
Signal
Power on
Power o
Press and hold for more than 8 seconds. All lights
will turn o, then the rst and second lights will
turn solidly on, indicating that reset was successful.
Reset/
WPS
Reset
WPS
Press both WPS buttons (the one on your router,
and the one on your extender) for one second.
After about 1 minute, Lights 1 - 3 should turn be
solid green, indicating successful connection.
Choose
wi-2.4G-xxxx or
wi-5G-xxxx
Your home WiFi
network name (SSID)
Extender
Please select your home WiFi network to be extended
2.4G
5G
Signal
Ethernet
Ethernet
Light 1
Light 2
Light 3
Light 4
Light 5
After conguration is
completed, if you want to
change your extender's WiFi
network name or password,
"you must reset your extender
and perform the conguration
process again.
192.168.188.1
2. Launch a phone browser (e.g. Chrome/Firefox/Safari) and enter
192.168.188.1 in the address bar.
Note: If the login window does not appear, you need rstly to check
"your mobile data settings: if mobile data is enabled, please toggle
your mobile data to o and recongure one more time. If the above
method fails, please try resetting your extender and attempting the
conguration process once again.
Model: WD-R1200U
wifi-2.4G-xxxx
wifi-5G-xxxx
wifi-2.4G-XXXX
wifi-5G-XXXX
Setup Guide Video
FAQ
Foscam, Inc.
Website:https: www.foscam.com/faqs/view.html?id=256
2.4G
5G
LED Descriptions
V1.3
WiFi Extender
Getting Started
Power on
Plug the extender into a power outlet that is within 2 meters (6.56
feet) of your router. Wait until the 2.4G and 5G LED lights turn solid
green. If anything goes wrong, please press and hold the "Reset"
button on the side of the extender for more than 8 seconds (if the
reset process fails, please contact the seller).
Set UP
Method 1: Mobile Phone Setup
Please ensure that your phone
has successfully connected to
the extender's WiFi network
name (wi-2.4G-XXXX or
wi-5G-XXXX) before
launching the phone browser.
3. Enter the default password: admin (must be lower case).
4. Select your home WiFi network name (SSID) you want to extend.
5. Enter the password of your home WiFi network.
6. Set your extender’s new WiFi network name (SSID) and password.
The default SSID of the extender
(Foscam_6-pro-2.4G
and Foscam_6-pro-5G) can be
changed. The default password
can also be changed (the default
password is your router's WiFi
network password).
2.4G
5G
1
2
1. Turn o your mobile data, then connect your mobile phone to
the extender's WiFi network name (SSID): wi-5G-XXXX or
wi-2.4G-XXXX (‘XXXX’ is the last 4 letters of the MAC Address
that is labeled on the back of the extender).
TP-LINK_BFF5
Foscam_1
Foscam_2
Foscam_3
Foscam_4
Foscam_5
Foscam_6
Foscam_7
Foscam_6
Foscam_7
Foscam_8
Foscam_9
7. Please check your extender's WiFi network name (SSID) and
password. If they are correct, click Start Connect and wait 30-60s.
Foscam_6
Foscam_6-pro-2.4G
Foscam_6-pro-5G
Method 2: PC Setup
2. Launch a web browser (Chrome/Firefox/Safari) and enter
192.168.188.1 in the address bar.
You can also connect your computer and extender with an
ethernet cable, then launch a web browser and enter
192.168.188.1 to congure your extender.
Note: If the login page does not appear, try another web browser
and attempt conguration once more. If the above method fails,
you can also try resetting the extender before attempting to
congure it again.
1. Connect your computer to the extender's WiFi network name
(SSID): wi-5G-XXXX or wi-2.4G-XXXX (‘XXXX’ is the last
4 letters of the MAC Address that is labeled on the back of the
extender).
Foscam_1
Foscam_2
Foscam_3
Foscam_4
Foscam_5
This device increases your WiFi signal coverage
(not the speed, which is determined by your internet
service provider).
Reset 8. After setup is completed, please view the rst three indicator
lights. If they are solid green, that indicates the conguration
process was successful. If the lights are not on, please reset the
extender and attempt conguration once more. To surf the web,
please connect your devices to your extender's WiFi network
name (SSID) which was set in Step 6.
Reset /WPS
Turn o your
mobile data
Settings Wi-Fi
Wi-Fi
Extender
Extender
Foscam_6-pro-2.4G
Foscam_6-pro-5G
Extender
The default extender name is XXXXX-pro can be changed.
Foscam_6
Please enter the password of your home WiFi network.
Extender
Extender
LED
Status
Indication(For Extender Mode)
Lights 1 and 2 are on: extender is normal.
Light 1 or Light 2 is o: extender is abnormal
Solid Green
O
On/O
On/O
The extender is connected to your router’s
wireless network.
No wireless connection is established.
The Ethernet port is connected to a powered-on
device.
The Ethernet port is connected to a powered-on
device.
2.4G
5G
Ethernet
Ethernet
Signal
Power on
Power o
Press and hold for more than 8 seconds. All lights
will turn o, then the rst and second lights will
turn solidly on, indicating that reset was successful.
Reset/
WPS
Reset
WPS
Press both WPS buttons (the one on your router,
and the one on your extender) for one second.
After about 1 minute, Lights 1 - 3 should turn be
solid green, indicating successful connection.
Choose
wi-2.4G-xxxx or
wi-5G-xxxx
Your home WiFi
network name (SSID)
Extender
Please select your home WiFi network to be extended
2.4G
5G
Signal
Ethernet
Ethernet
Light 1
Light 2
Light 3
Light 4
Light 5
After conguration is
completed, if you want to
change your extender's WiFi
network name or password,
"you must reset your extender
and perform the conguration
process again.
192.168.188.1
2. Launch a phone browser (e.g. Chrome/Firefox/Safari) and enter
192.168.188.1 in the address bar.
Note: If the login window does not appear, you need rstly to check
"your mobile data settings: if mobile data is enabled, please toggle
your mobile data to o and recongure one more time. If the above
method fails, please try resetting your extender and attempting the
conguration process once again.
Model: WD-R1200U
wifi-2.4G-xxxx
wifi-5G-xxxx
wifi-2.4G-XXXX
wifi-5G-XXXX
Setup Guide Video
FAQ
Foscam, Inc.
Website:https: www.foscam.com/faqs/view.html?id=256
3. Enter the default password: admin (must be lower case).
4. Select your home WiFi network name (SSID) you want to extend.
5. Enter the password of your home WiFi network.
1. Plug the extender into a wall that is about halfway between
router and internet-capable devices. You should a location in
accordance with the diagram below.
2. Wait for about 2 minutes until the rst three indicator lights
turn solid green. If they do not, relocate the extender closer to
the router.
FAQ (Frequently Asked Question):
Q2: How to conrm the WiFi range extender has been
congure successfully?
Please focus on the rst three lights on the extender. If the rst
three signal lights turn solid green, this means that you have
congure successfully. If not, congured one more time.
Q3: Can the extender improve my network speed?
No, it can't: all WiFi extenders can only increase the distance
coverage of your WiFi network.
Q4: If my extender frequently loses connection, what can I do?
If your extender's connection is frequently lost, you can reduce
the distance between your router and the extender.
Relocate
3
7. Please check your extender's WiFi network name (SSID) and
password. If they are correct, click Start Connect and wait 30-60s.
2. After pressing the WPS button of your router, within one minute
press and hold the WPS button on extender for 1 second. Wait
one minute, The rst three LED signal indicator lights will
turn solid green, indicating successful conguration.
Note: If the rst three LED indicator lights does not become solid
green, try again or use Method 1 (mobile phone setup) or Method 2
(PC setup). Some routers may not have a WPS function in which
case, pleaseuse setup Method 1 or Method 2.
Method 3: WPS Setup
1. Press the WPS button on your router for 1 second.
Press the WPS button
Press the WPS button
6. Set your extender’s new WiFi network name and password.
Foscam_6
Foscam_6-pro-2.4G
Foscam_6-pro-5G
The default WiFi network names
(SSID) of the extender
(Foscam_6-pro-2.4G and
Foscam_6-pro-5G) can be
changed. The default passwords
can also be changed (the default
password is your router’s WiFi
network password).
Please ensure that your
computer has successfully
connected to the extender's
WiFi network name
(wi-2.4G-XXXX or
wi-5G-XXXX) before
launching a web browser.
admin
8. After setup is completed, please view the rst three indicator
lights. If they are solid green, that indicates the conguration
process was successful. If the lights are not on, please reset the
extender and attempt conguration once more. To surf the web,
please connect your devices to your extender's WiFi network
name (SSID)", which was set in Step 6.
WPS
Q5: Where is the reset button and how can I reset the extender?
The reset button is on the left side of the extender. Press the
Reset and hold this button for more than 8 seconds. The
extender will reboot.
Q1: If I cannot access the extender’s web management page,
what can I do?
Make sure your computer or mobile phone (disable mobile data)
is connected to the extender network, not your router network.
The extender default SSID is "wi-5G-XXXX" or
"wi-2.4G-XXXX" (XXXX is the last 4 letters of the MAC
address that is labeled on the back of the extender).
Please rstly try using Chrome/Firefox/Safari/IE for conguration.
Reset the extender and recongure one more time.
If you still have any questions, please contact our technical support
Q6: The extended signal is strong, but has low speed.
We suggest placing the extender about halfway between your
router and the devices. The location you choose must also be
within the WiFi signal range of your router.
If you are too close to your router, please switch to the router’s
WiFi network (SSID) manually.
Foscam_6
Foscam_5
Foscam_4
Extender
Extender
Foscam_6-pro-5G
foscam123
Foscam_6
Foscam_6-pro-2.4G
Extender
Please enter the password of your home WiFi network
The default extender name is XXXXX-pro can be changed.
CE Certificate statement Website:
https://www.foscam.com/company/ce-certificate.html
Exporter and Importer Information Opened to Public:
https://www.foscam.com/company/open-information.html
Your home WiFi
network name (SSID)
Please select your home WiFi network to be extended
Tips: After conguration is completed, if you want to change your
extender's WiFi network name or password, you must reset your
extender and perform the conguration process again.
Green: Suitable location
Router Location Devices
Manufacturer: Shenzhen Foscam Intelligent Technology Co., Ltd
Addr: Room 901, Unit B, Building 7, Xingke 1st Street
Vanke Cloud City Phase 1, Nanshan Dist., Shenzhen, 518055,
China
FAQ Setup Guide Video
3. Enter the default password: admin (must be lower case).
4. Select your home WiFi network name (SSID) you want to extend.
5. Enter the password of your home WiFi network.
1. Plug the extender into a wall that is about halfway between
router and internet-capable devices. You should a location in
accordance with the diagram below.
2. Wait for about 2 minutes until the rst three indicator lights
turn solid green. If they do not, relocate the extender closer to
the router.
FAQ (Frequently Asked Question):
Q2: How to conrm the WiFi range extender has been
congure successfully?
Please focus on the rst three lights on the extender. If the rst
three signal lights turn solid green, this means that you have
congure successfully. If not, congured one more time.
Q3: Can the extender improve my network speed?
No, it can't: all WiFi extenders can only increase the distance
coverage of your WiFi network.
Q4: If my extender frequently loses connection, what can I do?
If your extender's connection is frequently lost, you can reduce
the distance between your router and the extender.
Relocate
3
7. Please check your extender's WiFi network name (SSID) and
password. If they are correct, click Start Connect and wait 30-60s.
2. After pressing the WPS button of your router, within one minute
press and hold the WPS button on extender for 1 second. Wait
one minute, The rst three LED signal indicator lights will
turn solid green, indicating successful conguration.
Note: If the rst three LED indicator lights does not become solid
green, try again or use Method 1 (mobile phone setup) or Method 2
(PC setup). Some routers may not have a WPS function in which
case, pleaseuse setup Method 1 or Method 2.
Method 3: WPS Setup
1. Press the WPS button on your router for 1 second.
Press the WPS button
Press the WPS button
6. Set your extender’s new WiFi network name and password.
Foscam_6
Foscam_6-pro-2.4G
Foscam_6-pro-5G
The default WiFi network names
(SSID) of the extender
(Foscam_6-pro-2.4G and
Foscam_6-pro-5G) can be
changed. The default passwords
can also be changed (the default
password is your router’s WiFi
network password).
Please ensure that your
computer has successfully
connected to the extender's
WiFi network name
(wi-2.4G-XXXX or
wi-5G-XXXX) before
launching a web browser.
admin
8. After setup is completed, please view the rst three indicator
lights. If they are solid green, that indicates the conguration
process was successful. If the lights are not on, please reset the
extender and attempt conguration once more. To surf the web,
please connect your devices to your extender's WiFi network
name (SSID)", which was set in Step 6.
WPS
Q5: Where is the reset button and how can I reset the extender?
The reset button is on the left side of the extender. Press the
Reset and hold this button for more than 8 seconds. The
extender will reboot.
Q1: If I cannot access the extender’s web management page,
what can I do?
Make sure your computer or mobile phone (disable mobile data)
is connected to the extender network, not your router network.
The extender default SSID is "wi-5G-XXXX" or
"wi-2.4G-XXXX" (XXXX is the last 4 letters of the MAC
address that is labeled on the back of the extender).
Please rstly try using Chrome/Firefox/Safari/IE for conguration.
Reset the extender and recongure one more time.
If you still have any questions, please contact our technical support
Q6: The extended signal is strong, but has low speed.
We suggest placing the extender about halfway between your
router and the devices. The location you choose must also be
within the WiFi signal range of your router.
If you are too close to your router, please switch to the router’s
WiFi network (SSID) manually.
Foscam_6
Foscam_5
Foscam_4
Extender
Extender
Foscam_6-pro-5G
foscam123
Foscam_6
Foscam_6-pro-2.4G
Extender
Please enter the password of your home WiFi network
The default extender name is XXXXX-pro can be changed.
CE Certificate statement Website:
https://www.foscam.com/company/ce-certificate.html
Exporter and Importer Information Opened to Public:
https://www.foscam.com/company/open-information.html
Your home WiFi
network name (SSID)
Please select your home WiFi network to be extended
Tips: After conguration is completed, if you want to change your
extender's WiFi network name or password, you must reset your
extender and perform the conguration process again.
Green: Suitable location
Router Location Devices
Manufacturer: Shenzhen Foscam Intelligent Technology Co., Ltd
Addr: Room 901, Unit B, Building 7, Xingke 1st Street
Vanke Cloud City Phase 1, Nanshan Dist., Shenzhen, 518055,
China
FAQ Setup Guide Video
3. Enter the default password: admin (must be lower case).
4. Select your home WiFi network name (SSID) you want to extend.
5. Enter the password of your home WiFi network.
1. Plug the extender into a wall that is about halfway between
router and internet-capable devices. You should a location in
accordance with the diagram below.
2. Wait for about 2 minutes until the rst three indicator lights
turn solid green. If they do not, relocate the extender closer to
the router.
FAQ (Frequently Asked Question):
Q2: How to conrm the WiFi range extender has been
congure successfully?
Please focus on the rst three lights on the extender. If the rst
three signal lights turn solid green, this means that you have
congure successfully. If not, congured one more time.
Q3: Can the extender improve my network speed?
No, it can't: all WiFi extenders can only increase the distance
coverage of your WiFi network.
Q4: If my extender frequently loses connection, what can I do?
If your extender's connection is frequently lost, you can reduce
the distance between your router and the extender.
Relocate
3
7. Please check your extender's WiFi network name (SSID) and
password. If they are correct, click Start Connect and wait 30-60s.
2. After pressing the WPS button of your router, within one minute
press and hold the WPS button on extender for 1 second. Wait
one minute, The rst three LED signal indicator lights will
turn solid green, indicating successful conguration.
Note: If the rst three LED indicator lights does not become solid
green, try again or use Method 1 (mobile phone setup) or Method 2
(PC setup). Some routers may not have a WPS function in which
case, pleaseuse setup Method 1 or Method 2.
Method 3: WPS Setup
1. Press the WPS button on your router for 1 second.
Press the WPS button
Press the WPS button
6. Set your extender’s new WiFi network name and password.
Foscam_6
Foscam_6-pro-2.4G
Foscam_6-pro-5G
The default WiFi network names
(SSID) of the extender
(Foscam_6-pro-2.4G and
Foscam_6-pro-5G) can be
changed. The default passwords
can also be changed (the default
password is your router’s WiFi
network password).
Please ensure that your
computer has successfully
connected to the extender's
WiFi network name
(wi-2.4G-XXXX or
wi-5G-XXXX) before
launching a web browser.
admin
8. After setup is completed, please view the rst three indicator
lights. If they are solid green, that indicates the conguration
process was successful. If the lights are not on, please reset the
extender and attempt conguration once more. To surf the web,
please connect your devices to your extender's WiFi network
name (SSID)", which was set in Step 6.
WPS
Q5: Where is the reset button and how can I reset the extender?
The reset button is on the left side of the extender. Press the
Reset and hold this button for more than 8 seconds. The
extender will reboot.
Q1: If I cannot access the extender’s web management page,
what can I do?
Make sure your computer or mobile phone (disable mobile data)
is connected to the extender network, not your router network.
The extender default SSID is "wi-5G-XXXX" or
"wi-2.4G-XXXX" (XXXX is the last 4 letters of the MAC
address that is labeled on the back of the extender).
Please rstly try using Chrome/Firefox/Safari/IE for conguration.
Reset the extender and recongure one more time.
If you still have any questions, please contact our technical support
Q6: The extended signal is strong, but has low speed.
We suggest placing the extender about halfway between your
router and the devices. The location you choose must also be
within the WiFi signal range of your router.
If you are too close to your router, please switch to the router’s
WiFi network (SSID) manually.
Foscam_6
Foscam_5
Foscam_4
Extender
Extender
Foscam_6-pro-5G
foscam123
Foscam_6
Foscam_6-pro-2.4G
Extender
Please enter the password of your home WiFi network
The default extender name is XXXXX-pro can be changed.
CE Certificate statement Website:
https://www.foscam.com/company/ce-certificate.html
Exporter and Importer Information Opened to Public:
https://www.foscam.com/company/open-information.html
Your home WiFi
network name (SSID)
Please select your home WiFi network to be extended
Tips: After conguration is completed, if you want to change your
extender's WiFi network name or password, you must reset your
extender and perform the conguration process again.
Green: Suitable location
Router Location Devices
Manufacturer: Shenzhen Foscam Intelligent Technology Co., Ltd
Addr: Room 901, Unit B, Building 7, Xingke 1st Street
Vanke Cloud City Phase 1, Nanshan Dist., Shenzhen, 518055,
China
FAQ Setup Guide Video
3. Enter the default password: admin (must be lower case).
4. Select your home WiFi network name (SSID) you want to extend.
5. Enter the password of your home WiFi network.
1. Plug the extender into a wall that is about halfway between
router and internet-capable devices. You should a location in
accordance with the diagram below.
2. Wait for about 2 minutes until the rst three indicator lights
turn solid green. If they do not, relocate the extender closer to
the router.
FAQ (Frequently Asked Question):
Q2: How to conrm the WiFi range extender has been
congure successfully?
Please focus on the rst three lights on the extender. If the rst
three signal lights turn solid green, this means that you have
congure successfully. If not, congured one more time.
Q3: Can the extender improve my network speed?
No, it can't: all WiFi extenders can only increase the distance
coverage of your WiFi network.
Q4: If my extender frequently loses connection, what can I do?
If your extender's connection is frequently lost, you can reduce
the distance between your router and the extender.
Relocate
3
7. Please check your extender's WiFi network name (SSID) and
password. If they are correct, click Start Connect and wait 30-60s.
2. After pressing the WPS button of your router, within one minute
press and hold the WPS button on extender for 1 second. Wait
one minute, The rst three LED signal indicator lights will
turn solid green, indicating successful conguration.
Note: If the rst three LED indicator lights does not become solid
green, try again or use Method 1 (mobile phone setup) or Method 2
(PC setup). Some routers may not have a WPS function in which
case, pleaseuse setup Method 1 or Method 2.
Method 3: WPS Setup
1. Press the WPS button on your router for 1 second.
Press the WPS button
Press the WPS button
6. Set your extender’s new WiFi network name and password.
Foscam_6
Foscam_6-pro-2.4G
Foscam_6-pro-5G
The default WiFi network names
(SSID) of the extender
(Foscam_6-pro-2.4G and
Foscam_6-pro-5G) can be
changed. The default passwords
can also be changed (the default
password is your router’s WiFi
network password).
Please ensure that your
computer has successfully
connected to the extender's
WiFi network name
(wi-2.4G-XXXX or
wi-5G-XXXX) before
launching a web browser.
admin
8. After setup is completed, please view the rst three indicator
lights. If they are solid green, that indicates the conguration
process was successful. If the lights are not on, please reset the
extender and attempt conguration once more. To surf the web,
please connect your devices to your extender's WiFi network
name (SSID)", which was set in Step 6.
WPS
Q5: Where is the reset button and how can I reset the extender?
The reset button is on the left side of the extender. Press the
Reset and hold this button for more than 8 seconds. The
extender will reboot.
Q1: If I cannot access the extender’s web management page,
what can I do?
Make sure your computer or mobile phone (disable mobile data)
is connected to the extender network, not your router network.
The extender default SSID is "wi-5G-XXXX" or
"wi-2.4G-XXXX" (XXXX is the last 4 letters of the MAC
address that is labeled on the back of the extender).
Please rstly try using Chrome/Firefox/Safari/IE for conguration.
Reset the extender and recongure one more time.
If you still have any questions, please contact our technical support
Q6: The extended signal is strong, but has low speed.
We suggest placing the extender about halfway between your
router and the devices. The location you choose must also be
within the WiFi signal range of your router.
If you are too close to your router, please switch to the router’s
WiFi network (SSID) manually.
Foscam_6
Foscam_5
Foscam_4
Extender
Extender
Foscam_6-pro-5G
foscam123
Foscam_6
Foscam_6-pro-2.4G
Extender
Please enter the password of your home WiFi network
The default extender name is XXXXX-pro can be changed.
CE Certificate statement Website:
https://www.foscam.com/company/ce-certificate.html
Exporter and Importer Information Opened to Public:
https://www.foscam.com/company/open-information.html
Your home WiFi
network name (SSID)
Please select your home WiFi network to be extended
Tips: After conguration is completed, if you want to change your
extender's WiFi network name or password, you must reset your
extender and perform the conguration process again.
Green: Suitable location
Router Location Devices
Manufacturer: Shenzhen Foscam Intelligent Technology Co., Ltd
Addr: Room 901, Unit B, Building 7, Xingke 1st Street
Vanke Cloud City Phase 1, Nanshan Dist., Shenzhen, 518055,
China
FAQ Setup Guide Video
3. Enter the default password: admin (must be lower case).
4. Select your home WiFi network name (SSID) you want to extend.
5. Enter the password of your home WiFi network.
1. Plug the extender into a wall that is about halfway between
router and internet-capable devices. You should a location in
accordance with the diagram below.
2. Wait for about 2 minutes until the rst three indicator lights
turn solid green. If they do not, relocate the extender closer to
the router.
FAQ (Frequently Asked Question):
Q2: How to conrm the WiFi range extender has been
congure successfully?
Please focus on the rst three lights on the extender. If the rst
three signal lights turn solid green, this means that you have
congure successfully. If not, congured one more time.
Q3: Can the extender improve my network speed?
No, it can't: all WiFi extenders can only increase the distance
coverage of your WiFi network.
Q4: If my extender frequently loses connection, what can I do?
If your extender's connection is frequently lost, you can reduce
the distance between your router and the extender.
Relocate
3
7. Please check your extender's WiFi network name (SSID) and
password. If they are correct, click Start Connect and wait 30-60s.
2. After pressing the WPS button of your router, within one minute
press and hold the WPS button on extender for 1 second. Wait
one minute, The rst three LED signal indicator lights will
turn solid green, indicating successful conguration.
Note: If the rst three LED indicator lights does not become solid
green, try again or use Method 1 (mobile phone setup) or Method 2
(PC setup). Some routers may not have a WPS function in which
case, pleaseuse setup Method 1 or Method 2.
Method 3: WPS Setup
1. Press the WPS button on your router for 1 second.
Press the WPS button
Press the WPS button
6. Set your extender’s new WiFi network name and password.
Foscam_6
Foscam_6-pro-2.4G
Foscam_6-pro-5G
The default WiFi network names
(SSID) of the extender
(Foscam_6-pro-2.4G and
Foscam_6-pro-5G) can be
changed. The default passwords
can also be changed (the default
password is your router’s WiFi
network password).
Please ensure that your
computer has successfully
connected to the extender's
WiFi network name
(wi-2.4G-XXXX or
wi-5G-XXXX) before
launching a web browser.
admin
8. After setup is completed, please view the rst three indicator
lights. If they are solid green, that indicates the conguration
process was successful. If the lights are not on, please reset the
extender and attempt conguration once more. To surf the web,
please connect your devices to your extender's WiFi network
name (SSID)", which was set in Step 6.
WPS
Q5: Where is the reset button and how can I reset the extender?
The reset button is on the left side of the extender. Press the
Reset and hold this button for more than 8 seconds. The
extender will reboot.
Q1: If I cannot access the extender’s web management page,
what can I do?
Make sure your computer or mobile phone (disable mobile data)
is connected to the extender network, not your router network.
The extender default SSID is "wi-5G-XXXX" or
"wi-2.4G-XXXX" (XXXX is the last 4 letters of the MAC
address that is labeled on the back of the extender).
Please rstly try using Chrome/Firefox/Safari/IE for conguration.
Reset the extender and recongure one more time.
If you still have any questions, please contact our technical support
Q6: The extended signal is strong, but has low speed.
We suggest placing the extender about halfway between your
router and the devices. The location you choose must also be
within the WiFi signal range of your router.
If you are too close to your router, please switch to the router’s
WiFi network (SSID) manually.
Foscam_6
Foscam_5
Foscam_4
Extender
Extender
Foscam_6-pro-5G
foscam123
Foscam_6
Foscam_6-pro-2.4G
Extender
Please enter the password of your home WiFi network
The default extender name is XXXXX-pro can be changed.
CE Certificate statement Website:
https://www.foscam.com/company/ce-certificate.html
Exporter and Importer Information Opened to Public:
https://www.foscam.com/company/open-information.html
Your home WiFi
network name (SSID)
Please select your home WiFi network to be extended
Tips: After conguration is completed, if you want to change your
extender's WiFi network name or password, you must reset your
extender and perform the conguration process again.
Green: Suitable location
Router Location Devices
Manufacturer: Shenzhen Foscam Intelligent Technology Co., Ltd
Addr: Room 901, Unit B, Building 7, Xingke 1st Street
Vanke Cloud City Phase 1, Nanshan Dist., Shenzhen, 518055,
China
FAQ Setup Guide Video
3. Enter the default password: admin (must be lower case).
4. Select your home WiFi network name (SSID) you want to extend.
5. Enter the password of your home WiFi network.
1. Plug the extender into a wall that is about halfway between
router and internet-capable devices. You should a location in
accordance with the diagram below.
2. Wait for about 2 minutes until the rst three indicator lights
turn solid green. If they do not, relocate the extender closer to
the router.
FAQ (Frequently Asked Question):
Q2: How to conrm the WiFi range extender has been
congure successfully?
Please focus on the rst three lights on the extender. If the rst
three signal lights turn solid green, this means that you have
congure successfully. If not, congured one more time.
Q3: Can the extender improve my network speed?
No, it can't: all WiFi extenders can only increase the distance
coverage of your WiFi network.
Q4: If my extender frequently loses connection, what can I do?
If your extender's connection is frequently lost, you can reduce
the distance between your router and the extender.
Relocate
3
7. Please check your extender's WiFi network name (SSID) and
password. If they are correct, click Start Connect and wait 30-60s.
2. After pressing the WPS button of your router, within one minute
press and hold the WPS button on extender for 1 second. Wait
one minute, The rst three LED signal indicator lights will
turn solid green, indicating successful conguration.
Note: If the rst three LED indicator lights does not become solid
green, try again or use Method 1 (mobile phone setup) or Method 2
(PC setup). Some routers may not have a WPS function in which
case, pleaseuse setup Method 1 or Method 2.
Method 3: WPS Setup
1. Press the WPS button on your router for 1 second.
Press the WPS button
Press the WPS button
6. Set your extender’s new WiFi network name and password.
Foscam_6
Foscam_6-pro-2.4G
Foscam_6-pro-5G
The default WiFi network names
(SSID) of the extender
(Foscam_6-pro-2.4G and
Foscam_6-pro-5G) can be
changed. The default passwords
can also be changed (the default
password is your router’s WiFi
network password).
Please ensure that your
computer has successfully
connected to the extender's
WiFi network name
(wi-2.4G-XXXX or
wi-5G-XXXX) before
launching a web browser.
admin
8. After setup is completed, please view the rst three indicator
lights. If they are solid green, that indicates the conguration
process was successful. If the lights are not on, please reset the
extender and attempt conguration once more. To surf the web,
please connect your devices to your extender's WiFi network
name (SSID)", which was set in Step 6.
WPS
Q5: Where is the reset button and how can I reset the extender?
The reset button is on the left side of the extender. Press the
Reset and hold this button for more than 8 seconds. The
extender will reboot.
Q1: If I cannot access the extender’s web management page,
what can I do?
Make sure your computer or mobile phone (disable mobile data)
is connected to the extender network, not your router network.
The extender default SSID is "wi-5G-XXXX" or
"wi-2.4G-XXXX" (XXXX is the last 4 letters of the MAC
address that is labeled on the back of the extender).
Please rstly try using Chrome/Firefox/Safari/IE for conguration.
Reset the extender and recongure one more time.
If you still have any questions, please contact our technical support
Q6: The extended signal is strong, but has low speed.
We suggest placing the extender about halfway between your
router and the devices. The location you choose must also be
within the WiFi signal range of your router.
If you are too close to your router, please switch to the router’s
WiFi network (SSID) manually.
Foscam_6
Foscam_5
Foscam_4
Extender
Extender
Foscam_6-pro-5G
foscam123
Foscam_6
Foscam_6-pro-2.4G
Extender
Please enter the password of your home WiFi network
The default extender name is XXXXX-pro can be changed.
CE Certificate statement Website:
https://www.foscam.com/company/ce-certificate.html
Exporter and Importer Information Opened to Public:
https://www.foscam.com/company/open-information.html
Your home WiFi
network name (SSID)
Please select your home WiFi network to be extended
Tips: After conguration is completed, if you want to change your
extender's WiFi network name or password, you must reset your
extender and perform the conguration process again.
Green: Suitable location
Router Location Devices
Manufacturer: Shenzhen Foscam Intelligent Technology Co., Ltd
Addr: Room 901, Unit B, Building 7, Xingke 1st Street
Vanke Cloud City Phase 1, Nanshan Dist., Shenzhen, 518055,
China
FAQ Setup Guide Video
3. Enter the default password: admin (must be lower case).
4. Select your home WiFi network name (SSID) you want to extend.
5. Enter the password of your home WiFi network.
1. Plug the extender into a wall that is about halfway between
router and internet-capable devices. You should a location in
accordance with the diagram below.
2. Wait for about 2 minutes until the rst three indicator lights
turn solid green. If they do not, relocate the extender closer to
the router.
FAQ (Frequently Asked Question):
Q2: How to conrm the WiFi range extender has been
congure successfully?
Please focus on the rst three lights on the extender. If the rst
three signal lights turn solid green, this means that you have
congure successfully. If not, congured one more time.
Q3: Can the extender improve my network speed?
No, it can't: all WiFi extenders can only increase the distance
coverage of your WiFi network.
Q4: If my extender frequently loses connection, what can I do?
If your extender's connection is frequently lost, you can reduce
the distance between your router and the extender.
Relocate
3
7. Please check your extender's WiFi network name (SSID) and
password. If they are correct, click Start Connect and wait 30-60s.
2. After pressing the WPS button of your router, within one minute
press and hold the WPS button on extender for 1 second. Wait
one minute, The rst three LED signal indicator lights will
turn solid green, indicating successful conguration.
Note: If the rst three LED indicator lights does not become solid
green, try again or use Method 1 (mobile phone setup) or Method 2
(PC setup). Some routers may not have a WPS function in which
case, pleaseuse setup Method 1 or Method 2.
Method 3: WPS Setup
1. Press the WPS button on your router for 1 second.
Press the WPS button
Press the WPS button
6. Set your extender’s new WiFi network name and password.
Foscam_6
Foscam_6-pro-2.4G
Foscam_6-pro-5G
The default WiFi network names
(SSID) of the extender
(Foscam_6-pro-2.4G and
Foscam_6-pro-5G) can be
changed. The default passwords
can also be changed (the default
password is your router’s WiFi
network password).
Please ensure that your
computer has successfully
connected to the extender's
WiFi network name
(wi-2.4G-XXXX or
wi-5G-XXXX) before
launching a web browser.
admin
8. After setup is completed, please view the rst three indicator
lights. If they are solid green, that indicates the conguration
process was successful. If the lights are not on, please reset the
extender and attempt conguration once more. To surf the web,
please connect your devices to your extender's WiFi network
name (SSID)", which was set in Step 6.
WPS
Q5: Where is the reset button and how can I reset the extender?
The reset button is on the left side of the extender. Press the
Reset and hold this button for more than 8 seconds. The
extender will reboot.
Q1: If I cannot access the extender’s web management page,
what can I do?
Make sure your computer or mobile phone (disable mobile data)
is connected to the extender network, not your router network.
The extender default SSID is "wi-5G-XXXX" or
"wi-2.4G-XXXX" (XXXX is the last 4 letters of the MAC
address that is labeled on the back of the extender).
Please rstly try using Chrome/Firefox/Safari/IE for conguration.
Reset the extender and recongure one more time.
If you still have any questions, please contact our technical support
Q6: The extended signal is strong, but has low speed.
We suggest placing the extender about halfway between your
router and the devices. The location you choose must also be
within the WiFi signal range of your router.
If you are too close to your router, please switch to the router’s
WiFi network (SSID) manually.
Foscam_6
Foscam_5
Foscam_4
Extender
Extender
Foscam_6-pro-5G
foscam123
Foscam_6
Foscam_6-pro-2.4G
Extender
Please enter the password of your home WiFi network
The default extender name is XXXXX-pro can be changed.
CE Certificate statement Website:
https://www.foscam.com/company/ce-certificate.html
Exporter and Importer Information Opened to Public:
https://www.foscam.com/company/open-information.html
Your home WiFi
network name (SSID)
Please select your home WiFi network to be extended
Tips: After conguration is completed, if you want to change your
extender's WiFi network name or password, you must reset your
extender and perform the conguration process again.
Green: Suitable location
Router Location Devices
Manufacturer: Shenzhen Foscam Intelligent Technology Co., Ltd
Addr: Room 901, Unit B, Building 7, Xingke 1st Street
Vanke Cloud City Phase 1, Nanshan Dist., Shenzhen, 518055,
China
FAQ Setup Guide Video
3. Enter the default password: admin (must be lower case).
4. Select your home WiFi network name (SSID) you want to extend.
5. Enter the password of your home WiFi network.
1. Plug the extender into a wall that is about halfway between
router and internet-capable devices. You should a location in
accordance with the diagram below.
2. Wait for about 2 minutes until the rst three indicator lights
turn solid green. If they do not, relocate the extender closer to
the router.
FAQ (Frequently Asked Question):
Q2: How to conrm the WiFi range extender has been
congure successfully?
Please focus on the rst three lights on the extender. If the rst
three signal lights turn solid green, this means that you have
congure successfully. If not, congured one more time.
Q3: Can the extender improve my network speed?
No, it can't: all WiFi extenders can only increase the distance
coverage of your WiFi network.
Q4: If my extender frequently loses connection, what can I do?
If your extender's connection is frequently lost, you can reduce
the distance between your router and the extender.
Relocate
3
7. Please check your extender's WiFi network name (SSID) and
password. If they are correct, click Start Connect and wait 30-60s.
2. After pressing the WPS button of your router, within one minute
press and hold the WPS button on extender for 1 second. Wait
one minute, The rst three LED signal indicator lights will
turn solid green, indicating successful conguration.
Note: If the rst three LED indicator lights does not become solid
green, try again or use Method 1 (mobile phone setup) or Method 2
(PC setup). Some routers may not have a WPS function in which
case, pleaseuse setup Method 1 or Method 2.
Method 3: WPS Setup
1. Press the WPS button on your router for 1 second.
Press the WPS button
Press the WPS button
6. Set your extender’s new WiFi network name and password.
Foscam_6
Foscam_6-pro-2.4G
Foscam_6-pro-5G
The default WiFi network names
(SSID) of the extender
(Foscam_6-pro-2.4G and
Foscam_6-pro-5G) can be
changed. The default passwords
can also be changed (the default
password is your router’s WiFi
network password).
Please ensure that your
computer has successfully
connected to the extender's
WiFi network name
(wi-2.4G-XXXX or
wi-5G-XXXX) before
launching a web browser.
admin
8. After setup is completed, please view the rst three indicator
lights. If they are solid green, that indicates the conguration
process was successful. If the lights are not on, please reset the
extender and attempt conguration once more. To surf the web,
please connect your devices to your extender's WiFi network
name (SSID)", which was set in Step 6.
WPS
Q5: Where is the reset button and how can I reset the extender?
The reset button is on the left side of the extender. Press the
Reset and hold this button for more than 8 seconds. The
extender will reboot.
Q1: If I cannot access the extender’s web management page,
what can I do?
Make sure your computer or mobile phone (disable mobile data)
is connected to the extender network, not your router network.
The extender default SSID is "wi-5G-XXXX" or
"wi-2.4G-XXXX" (XXXX is the last 4 letters of the MAC
address that is labeled on the back of the extender).
Please rstly try using Chrome/Firefox/Safari/IE for conguration.
Reset the extender and recongure one more time.
If you still have any questions, please contact our technical support
Q6: The extended signal is strong, but has low speed.
We suggest placing the extender about halfway between your
router and the devices. The location you choose must also be
within the WiFi signal range of your router.
If you are too close to your router, please switch to the router’s
WiFi network (SSID) manually.
Foscam_6
Foscam_5
Foscam_4
Extender
Extender
Foscam_6-pro-5G
foscam123
Foscam_6
Foscam_6-pro-2.4G
Extender
Please enter the password of your home WiFi network
The default extender name is XXXXX-pro can be changed.
CE Certificate statement Website:
https://www.foscam.com/company/ce-certificate.html
Exporter and Importer Information Opened to Public:
https://www.foscam.com/company/open-information.html
Your home WiFi
network name (SSID)
Please select your home WiFi network to be extended
Tips: After conguration is completed, if you want to change your
extender's WiFi network name or password, you must reset your
extender and perform the conguration process again.
Green: Suitable location
Router Location Devices
Manufacturer: Shenzhen Foscam Intelligent Technology Co., Ltd
Addr: Room 901, Unit B, Building 7, Xingke 1st Street
Vanke Cloud City Phase 1, Nanshan Dist., Shenzhen, 518055,
China
FAQ Setup Guide Video
Other manuals for WD-R1200U
1
Table of contents
Other Foscam Extender manuals
