FP FPi 1015 User manual

FPi 1015
Inserting System
Quick Install Guide
11/2022

FCC Compliance
This equipment has been tested and found to comply with the limits for a
Class A digital device, pursuant to part 15 of the FCC rules. These limits
are designed to provide reasonable protection against interference when
the equipment is operated in a commercial environment. This equipment
generates, uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the instruction manual, may cause
interference to radio communications. Operation of this equipment in a
residential area is likely to cause interference, in which case the user will
be required to correct the interference at his own expense. Use only a
shielded interface cable to operate this equipment with a printer or other
peripheral device.
CAUTION: Changes or modications to this equipment not expressly
approved by the party responsible for compliance (Francotyp-Postalia)
could void the user’s authority to operate the equipment.
It is certified that this system complies with all applicable
Directives of the European Union.
Francotyp-Postalia GmbH
Prenzlauer Promenade 28 · 13089 Berlin (Germany)
Freecall: [phone]
[email protected] · fp-francotyp.com
All rights reserved. This guide may not be reproduced
in whole or in part in any fashion or stored in a
retrieval system of any type or transmitted by any
means, electronically or mechanically, without the
express, written permission of Francotyp-Postalia.
We have made every reasonable effort to ensure the
accuracy and usefulness of this manual; however, we
cannot assume responsibility for errors or omissions
or liability for the misuse or misapplication of our
products.
Due to our continuing program of product improve-
ment, equipment and material specifications as well
as performance features are subject to change without
notice. Your machine may not have some of the
features described in this book.
P-FPXxXxx_EN; Rev. 00
11/2022
©2022 Francotyp-Postalia GmbH
International English Version

3
Quick Install Guide
Francotyp-Postalia GmbH | FPi 1000 | P-FPXxXxx_EN; Rev. 0011/2022
The FPi 1000 can be supplied in the following variants:
• FPi 1010 • FPi 1020
• FPi 1015 • FPi 1025
Follow the instructions in this guide to get your FPi 1000 system setup and
running. Included in this guide are instructions for the following:
• Unpack • Load envelopes
• Set in place • Load sheets
• Connect / Turn On • Setup
• Change display language
• Check the moistener
• Run a test piece
IMPORTANT: If you purchased the optional second sheet feeder, unpack it
and position it on the desktop BEFORE you follow these instructions.

4
Quick Install Guide
Francotyp-Postalia GmbH | FPi 1000 | P-FPXxXxx_EN; Rev. 00 11/2022
Step 1: Unpack
1. Lift out the following
accessories and put them to
one side:
• Test paper and envelopes
• Power Cord
2. Remove the cardboard and
foam packing.

5
Quick Install Guide
Francotyp-Postalia GmbH | FPi 1000 | P-FPXxXxx_EN; Rev. 0011/2022
Step 2: Set in Place
1. Lift the inserter by
its handles and
place it on a flat
surface.
.
SAFETY NOTICE!
• Lift the inserter only by its lifting handles
• Lift correctly (bend knees and keep back
straight)
• The inserter weighs about 38 lb (17.5 kg) -
it is recommended you get help to lift it
2. If you have the
optional second
sheet feeder,
position the inserter
on that feeder now.

6
Quick Install Guide
Francotyp-Postalia GmbH | FPi 1000 | P-FPXxXxx_EN; Rev. 00 11/2022
Step 3: Connect and Turn On
1. Connect the power cord.
2. Switch the power ON.
(The power switch
is on the back panel
next to the power
cord.)
After a few seconds,
the display shows
READY.
SAFETY NOTICE!
• Locate the system close to a power socket
• Use the power cord supplied
• See the FPi 1000 Operating Guide for
complete safety and connection information

7
Quick Install Guide
Francotyp-Postalia GmbH | FPi 1000 | P-FPXxXxx_EN; Rev. 0011/2022
Step 4: Change Display Language
1. Turn the machine on and at the same time press and hold the no and
yes keys on the control panel. The word Password appears.
2. Press the no key until 99 appears. (If you scroll past 99, press the yes
key to scroll back.)
Password 0 Password 99
3. Press the Menu/Enter key.
4. Press the no key until you see your language.
5. Press the Menu/Enter key to select the language.
6. Turn the machine off and on. The language is now set. The machine
boots up at the next step in your setup, which is Check the Moistener.
Password 0
Menu/Enter
no yes

8
Quick Install Guide
Francotyp-Postalia GmbH | FPi 1000 | P-FPXxXxx_EN; Rev. 00 11/2022
Step 5: Check the Moistener
1. Slide the moistener tray open.
2. Fill the moistener with water or
FP seal-IT.
3. Slide the moistener tray closed.
NOTE: It takes about ve minutes for the moistener to get fully wet and
ready for use. You can continue setting up the machine during this time.

9
Quick Install Guide
Francotyp-Postalia GmbH | FPi 1000 | P-FPXxXxx_EN; Rev. 0011/2022
Step 6: Load Envelopes
Use the test paper and envelopes to practice using the system and to
make sure that system is working correctly.
1. Fan test envelopes marked with
the letter B.
2. Tap the stack of envelopes to
align edges.
3. Place envelopes in feeder B -
RIGHT WAY UP and
FACING YOU.
4. Use blue handles at the rear of
the guides to move them.
Slide the side guides until they
just touch the envelopes.
• If guides are too tight,
envelopes may stall.
• If they are too loose,
envelopes may skew.
1
2
2

10
Quick Install Guide
Francotyp-Postalia GmbH | FPi 1000 | P-FPXxXxx_EN; Rev. 00 11/2022
Step 7: Load Sheets
1. Fan the stack of sheets test
sheets that are marked with A1.
2. Tap the stack to align the edges.
3. Place the stack of sheets in
feeder A1, FACE DOWN and
BOTTOM EDGE FIRST.
4. Push the backstop in until it just
touches the stack of sheets.
IMPORTANT:
• Always fan (aerate) sheets before loading.
• Always load sheets FACE DOWN and BOTTOM EDGE FIRST.

11
Quick Install Guide
Francotyp-Postalia GmbH | FPi 1000 | P-FPXxXxx_EN; Rev. 0011/2022
Step 8: Setup
The selection keys on the control panel enable you to turn feeders and
job options on and off. Pressing the keys repeatedly scrolls through the
options available on your system. When you have made a selection, the
associated LED indicator on the control panel turns green.
To select feeders and activate options:
1. Press the Feeder A1 selection key until the Feeder A1 LED turns
green.
2. Press the Envelope Feeder B selection key until the Envelope Fdr B
LED turns green.
3. Press the Seal selection key until the Seal LED tuns green.
Start
Feeder A1 LED
Feeder A1 key
Envelope
Fdr B key
Envelope
Fdr B LED
Seal LED
Seal key

12
Quick Install Guide
Francotyp-Postalia GmbH | FPi 1000 | P-FPXxXxx_EN; Rev. 00 11/2022
Step 9: Run a Test Piece
1. Press the Trial Piece button.
2. If the trail piece checks out ok, press Start.
3. Press Stop to stop processing.
NOTE: The trial piece will not be sealed so you can check the contents of
the envelope. This is normal. The counter will show the number of items
processed.
no yes
Menu/Enter
Feeder A1 Feeder A2
2nd Page
Seal
No Seal
Envelope Fdr B
Insert Fdr C
Fold Only
Trial Piece Start Stop
Ready 0
Trial Piece
Start
Stop

13
Quick Install Guide
Francotyp-Postalia GmbH | FPi 1000 | P-FPXxXxx_EN; Rev. 0011/2022
Step 10: Congratulations
Your FPi 1000 is now ready to use. There is a slot on the top right side of
the cover (shown in the image here) to store the FPi 1000 Operator Guide.
This guide explains how to use your new system.
If you experience any problems installing your equipment, please refer to
the "Troubleshooting" section in the FPi 1000 Operator Guide.

14
Declaration of Conformity
Francotyp-Postalia GmbH | FPi 1000 | P-FPXxXxx_EN; Rev. 00 11/2022
The Declaration of Conformity of the original manufacturer shown on the
following page is therefore fully applicable to the product(s) described here.

15
Declaration of Conformity
Francotyp-Postalia GmbH | FPi 1000 | P-FPXxXxx_EN; Rev. 0011/2022
DECLARATION OF CONFORMITY (En)
DÉCLARATION DE CONFORMITÉ (Fr)
KONFORMITÄTSERKLÄRUNG (De)
DICHIARAZIONE DI CONFORMITÀ (It)
FÖRSÄKRAN OM ÖVERENSSTÄMMELSE (Sw)
SAMSVARSERKLÆRING (Nor)
U.S.A.
Pitney Bowes, Inc.
3001 Summer street
Stamford, CT 06926
U.S.A.
EU
Pitney Bowes Deutschland GmbH
Poststr. 4-6
64293 Darmstadt
Germany
declare under our sole responsibility / Déclarons sous notre seule responsabilité / erklären, in alleiniger
Verantwortung / dichiariamo sotto nostra unica responsabilitá / försäkrar under eget ansvar / erklærer under
vårt eneansvar:
Product Type / Type de produit / Produkttyp / Tipo di prodotto / Produkttyp / Produkttype:
Relay™ 1000 Inserting System
Model / Modèle / Modell / Modello / Modell / Modell:
H309, H311
Options / Options / Zubehor / Opzioni / Tillval / Tilleggsutstyr:
H31A
complies with following EU Directives and Standards / est conforme aux directives et normes CE suivantes /
entspricht den folgenden EU-Richtlinien und –Standards / e conforme alle seguenti direttive e standard CE /
foljer foljande EG-direktiv och standarder / er i samsvar med EU-direktivene og standardene nedenfor:
EMC / CEM/ EMV / CEM / EMC / EMC 2014/30/EC
EN 55032:2015 (Class A)
EN 61000-3-2:2019
EN 61000-3-3:2013 + A1 2019
EN 55035:2017
Low Voltage / Sécurité / Sicherheit / Sicurezza / Säkerhet /
Sikkerhet 2014/35/EC
EN 62368-1:2014/A11:2017
RoHS 2011/65/EU
EN 63000:2018
___________________________ 3-14-2022
Mark Scribe: Director HW Product Development
Pitney Bowes, Inc.
27 Waterview Drive
Shelton, CT 06848 U.S.A.

Francotyp-Postalia GmbH
Prenzlauer Promenade 28 · 13089 Berlin (Germany)
Freecall: [phone]
[email protected] · fp-francotyp.com