FRAMOS D435e User manual

INDUSTRIAL DEPTH CAMERA D435E
GETTING STARTED PAGE 1 / STARTER KIT BOX CONTENTS*
CONTACT DETAILS
[e-mail] | [phone]
www.framos.com | FRAMOS GmbH | Mehlbeerenstr. 2 | 82024 Taufkirchen | Germany
2
3 4
FRAMOS Industrial Depth Camera D435e, with M12 Ethernet and M8 power supply /
GPIO connectors.
1
FRAMOS GmbH · Mehlbeerenstr. 2 · 82024 Taufkirchen · Germany
D435e Data Cable
M12
RJ45
Wall
socket
adapter
Power Cable Docu-Link
M8
Box contents:
2Ethernet data cable with RJ45 connector (PC connection) on one side and M12
connector (camera connection) on the other side.
3Power adapter of wall socket mains supply to 12V with M8 camera connector.
4“Business Card” with the link to the landing page of the D435e where all documentation
and software can be downloaded.
1
* If you bought the camera only, no power adapter and no Ethernet cable will be part of the box

INDUSTRIAL DEPTH CAMERA D435E
GETTING STARTED PAGE 2 / SYSTEM SETUP
FRAMOS GmbH · Mehlbeerenstr. 2 · 82024 Taufkirchen · Germany
Steps of system setup:
Check if all components to run the camera are available. This includes the camera
itself, an Ethernet (M12) data cable and power supply (M8). Alternative system setup
utilizing single cable for both data and power is presented on page 3.
1
Connect the Ethernet data cable with the M12 connector to the lower plug on the left
side of the camera. Connect the RJ45 connector to Network Interface Card (NIC) on
your PC. Configure NIC to obtain IP address automatically.
2
Connect the power cable on the side of the M8 connector to the upper plug on the left
side of the camera and then plug the adapter into the wall socket.
M12RJ45
PC / Host Wall
Socket Depth Camera
M8
2
CONTACT DETAILS
[e-mail] | [phone]
www.framos.com | FRAMOS GmbH | Mehlbeerenstr. 2 | 82024 Taufkirchen | Germany
3
3

INDUSTRIAL DEPTH CAMERA D435E
GETTING STARTED PAGE 3 / SYSTEM SETUP (POE)
FRAMOS GmbH · Mehlbeerenstr. 2 · 82024 Taufkirchen · Germany
Steps of system setup (PoE):
In case a PoE switch is available, the camera can be powered via the same Ethernet
(M12) data cable used for data transfer.
1
Connect the Ethernet data cable with the M12 connector to the lower plug on the left
side of the camera. Connect the RJ45 connector to the PoE capable port of the PoE
switch. The camera will immediately start powering up.
2
Connect the PC to the PoE switch via standard RJ45 Ethernet cable (the port used for
the PC connection does not need to be PoE capable). Configure the used NIC to
obtain an IP address automatically.
M12RJ45
PC / Host
PoE
Switch Depth Camera
M8
2
CONTACT DETAILS
[e-mail] | [phone]
www.framos.com | FRAMOS GmbH | Mehlbeerenstr. 2 | 82024 Taufkirchen | Germany
3
3

INDUSTRIAL DEPTH CAMERA D435E
GETTING STARTED PAGE 4 / INSTALLATION
FRAMOS GmbH · Mehlbeerenstr. 2 · 82024 Taufkirchen · Germany
Installation:
2Install Intel® RealSense™ SDK with support for D435e camera (link above). Please
uninstall other versions of Intel® RealSense™ SDK before proceeding with the
installation.
CONTACT DETAILS
[e-mail] | [phone]
www.framos.com | FRAMOS GmbH | Mehlbeerenstr. 2 | 82024 Taufkirchen | Germany
Install FRAMOS CameraSuite on the host system (link above). Please uninstall other
versions of CameraSuite and follow the instructions provided inside the package for
successful installation. Reboot the system after the installation has finished.
1
3After installation, launch Intel® RealSense™ Viewer from the host terminal. It will
automatically connect to first camera discovered.
4Enable Depth and RGB streams to display them in the Intel® RealSense™ Viewer
application. For more information about how to use the Viewer application please
review the Intel® RealSense™ D400 Series/SR300 Viewer User Guide. Note that
some features of SDK might not be fully implemented in current D435e camera
firmware.
The Software Package for the FRAMOS D435e Industrial Depth Camera comprises of two
components:
▪FRAMOS CameraSuite
▪Intel® RealSense™ SDK with support for D435e camera
Please download the software here: Software package