Franke ABSINTHE FFP5290SB User manual

LIMITED LIFETIME WARRANTY
All faucets installed in a private residence will carry a limited lifetime
warranty on all mechanical parts to be free of manufacturing defects
in material and workmanship under normal usage. All chrome finishes
carry a limited lifetime warranty; all other finishes are warranted for
five (5) years form the original date of purchase.
Marine and Outdoor Installation
warranted for Marine and Outdoor installations.
This warranty applies only to the original owner, providing the product
has been installed in accordance with our installation instructions,
used as recommended and in a normal residential application. In the
event of a warranty claim, the owner will be required to provide proof
of purchase - save sales receipt. This warranty covers all components
which make the product operational. Franke, at its option, may repair
or replace the product or components necessary to restore the pro-
duct to good working condition. Franke reserves the right to inspect
the installation prior to the actual replacement of the product or com-
ponent part. This warranty does not cover misuse or abuse, acciden-
tal damages, scuffs or scratches, improper installation, abnormal
usage, negligence or damage caused by improper maintenance or
cleaning. Normal wear of parts is excluded from the warranty.
Damage caused by impurities or acts beyond our control are not
covered. Any product or part which has been repaired or altered in
any manner outside of Franke's factory, unless previously authorized
in writing by Franke, will void warranty. Any replacement excludes
transportation and any labor re-installation costs. This warranty
does not allow recovery of incidental or consequential damages such
as loss of use, delay, property damage or other consequential dama-
ge, and Franke accepts no liability for such damages.
The Franke warranty is limited to the above conditions and to the
warranty period specified herein and is exclusive.Franke DISCLAIMS
all other warranties, expressed or implied, including IMPLIED
WARRANTIES OF MERCHANTABILITY AND/OR FITNESS
FOR A PARTICULAR PURPOSE. This warranty gives you
specific legal rights that may vary from state to state.
Further information
For any further information about our products, about the installation of
IISTR111137#C08960
INSTALLATION MANUAL
FFP5200 - FFP5220 - FFP5270 - FFP5280
FFP5290SB
STANDARD MAINTENANCE AND TROUBLESHOOTING
REPLACING THE CARTRIDGE
GENERAL MAINTENANCE
Clean aerator periodically for any buildup .
Do not use harsh detergents, solvents, chemical agents, metallic sponges,
etc. that could harm the surface and damage the nish.
SPARE / REPLACEMENT LIST
A+B+C+G. Handle assembly F5201*
F3802*paC.D
E. Lock nut F3803
F. Cartridge F3804
them or about the guarantee, please contact our customer service
department:
Franke Kitchen Systems
800 Aviation Parkway
Smyrna, TN 37167, USA
Phone: [phone]
Email: [email protected]
ABSINTHE PREP PULL-DOWN
the original purchaser of its faucets effective January 1, 2003.
:Franke faucets are NOT
Franke Kitchen Systems,LLC extends the following warranty to
H. Pull out hose
I. Weight
J. Check Valve 1.75 gpm
K.
Aerator Key
L. Pull out spray assembly
REV. 3.09/2020
F5204
F3102
F3706
F2809
F5202*
Clean only with a soft sponge and soapy water.
Do not store chemicals or cleaning agents in the immediate vicinity of the
faucet and connection hoses. Chemical vapors could cause damage.
CH chrome
SN satin nickel
*Must specify nish
PN polished nickel
MB matte black
SB satin brass
M. Mounting Hardware Kit
N. Pull out supply hose
O.
Supply hoses
P. Fixing Kit
F5219
F5205
F5203
F3125
FF5200 - FF5220 - FF5270 - FF5280
FF5290SB
ABSINTHE KITCHEN PULL-DOWN
1. Shut o the water supply to the faucet.
2. Turn on the faucet briey to relieve any pressure inside the faucet.
3. Move the faucet handle to the “ OFF” position.
4. Unscrew lever handle C from the lever handle A.
5. Remove the pin handle set screw B using an allen key.
6. Pull the lever handle A from the faucet body .
7. Unscrew the cap D o of the lock nut E.
8. Unscrew the cartridge lock nut E.
9. Lift ceramic disk cartridge F from the body and repalce it with a new
one. Ensure the two lugs on bottom of the cartridge sit properly in the
allocated holes at the base of the body.
10. Re-assemble faucet in reverse order.
11. Test for leakage.
D
E
F
H
K
M
J
L
G
I
O
NP
C
B
A
H

TECHNICAL DATA
NOTE:
CONTENTS IN BOX
INSTALLATION INSTRUCTIONS
Contact us immediatly if you see inconsistencies.
Phone: [phone])
website: www.franke.us/ks.com
email: [e-mail]
Flow Rate
Recommended Water Pressure
Max. Water Pressure
Recommended Hot Water Temp.
Hole Size For Faucet
Certies this faucet complies with ASME A112.18.1 / CSA B125.1
& NSF 61, NSF 372 and AB1953
1.75 GPM at 60 PSI
30-75 PSI
145 PSI
120°-140° F
1 3/8”
1 Faucet assembly
2 Rubber washer
3 Rubber washer
4 Plastic ange
5 Fixing plate
6 Fixing nut
1
5
6
2
4
3
8
10
7
11
12
9
12 Key for aerator
7 Pull out Supply hose
8Spray hose
9
Weights
Screws
Supply hoses
10
11
1. Remove all contents from the package and check for completeness.
2. Turn o water supply.
3. Cut a mounting hole 1 3/8 diameter (35mm) in the desired position in
counter top or sink (if one isn’t available).
4. Place the rubber washer (2) over the mounting shank.
ATTENTION: The washer should be sitting between the countertop and
faucet base.
DO NOT use putty or other sealant at this location.
NOTES:
Solid surface installation: The countertop mounting surface needs to
be at and free of debris otherwise the faucet may not sit properly.
For tile installations, avoid installing faucet near or on top of grout lines.
This may cause a weak joint between the faucet and the counter and
could cause leaks.
5. Install the mounting hardware to the base of the faucet body in
the following order - rubber washer (3) plastic ange (4) and xing
plate (5) as ilustrated
6. Secure the faucet by tightening the Fixing Nut (6) onto the
mounting shank of the faucet the body (1).
2
5
1
4
3
6
2” (50 mm)
9. Connect the exible supply hoses (11) to the water supply in the
house.
7. Connect the pull out hose (8) to the pull out supply hose (7) using the
quick connect tting. Slide the quick connect tting sleeve to the
"open" position, insert the hose tting into the connector. You should
hear a "click". Slide the sleeve to the "lock" position, you should hear
another "click". This will ensure the tting is sealed and locked.
8. Place the weights (9) on the spray hose (8) with the screws (10).
Approximately 2” (50mm) above the bend in the bottom of the spray
hose.
7
11
8
10
10
9
9
10. Remove the aerator using the aerator key, turn on water, ush the
faucet for any debris and check for leaks.
Reinstall the aerator and ensure everything is functioning properly.