Franke ASCONA TAP User manual

FRANKE ASCONA TAP
Installation instructions
216
ø49
105
398
273

Technical data
Minimum water pressure: 7.25PSI (0.5 bar)
Maximum water pressure: 75PSI (5 bar)
Maximum hot water temperature: 70°C
Recommended hot water temperature: 65°C
Note: Exceeding these temperatures or water pressures
can result in damage to the tap.
A pressure reducing valve may be required to be fitted in
high water pressure situations.
Attention
Before installing the new mixer it is essential that you
thoroughly flush through the supply pipes in order to remove
any remaining swarf, solder or other impurities.
Failure to carry out this simple procedure could cause
problems or damage to the workings of the mixer.
Having first checked all new connections, turn on the mains
stopcock, close all taps except the new mixer and as the
system starts to refill check for leaks.
Once you have satisfied yourself that there are no leaks,
switch on the water heating.
Preparation
First shut off your water heating system then, with your
mains stopcock closed, open the lowest hot and cold taps
in the house and allow to run until the cold storage tank and
pipes are empty (the hot water storage cylinder always
remains full).
Installation
First screw the threaded stud into the mixer body. Screw the
tails into the mixer body and fully hand tighten.
After making any necessary alterations to existing pipework, pass
the plinth over the tails and fit in position.
The shaped upstand on the plinth will locate in the tap body
and the ‘O’ ring should be placed in the recess to make a
seal with the sink.
When the tap is in position (with the cold side on the right
when viewed from the front) slide the nylon bracing plate up to
the underside of the sink together with the retaining plate, and
secure by screwing the fixing nut finger tight.
Check that the mixer body and plinth are correctly positioned
and fully tighten fixing nut.
It is recommended that 15mm x 15mm compression fittings be
used to connect mixer to supply pipes. Cold is connected to
the right and hot on the left when viewed from the front.
Warning
These hints have been prepared for your guidance, you must
exercise due care at all times. We do not accept responsibility
for any problems that may occur through incorrect installation.
NB: If for any reason the spout is removed from the tap,
care must be taken when reinserting the spout into the body
to ensure that the Grub Screw is located in the split of the
white PTFE ring.
How to care for your tap
To maintain the appearance of this tap, ensure it is cleaned
only using a clean, soft damp cloth. A solution of warm water
and mild liquid detergent may be used where necessary, and
then the fitting rinsed thoroughly. Abrasive cleaners or acidic
cleaners MUST NOT BE USED under any circumstances.
Avoid contact with all solvents.

3986R
1263R
3735R-H
3794R-H
3794R-C
3311R
3734R
3728R
3735R-C
3668R
Available finish
115.0250.635 Chrome
115.0250.636 SilkSteel
Parts list as follows
FUN number Part name Part code
133.0068.761 Antisplash Chrome 1263R CH
133.0068.762 Antisplash SilkSteel 1263R SS
133.0358.051 Spout Chrome 3986R CH
133.0358.052 Spout SilkSteel 3986R SS
133.0277.067 ‘O’ ring kit 3668R
133.0251.339 Hot handle Chrome 3735R-H CH
133.0251.353 Cold handle Chrome 3735R-C CH
133.0251.354 Hot handle SilkSteel 3735R-H SS
133.0251.355 Cold handle SilkSteel 3735R-C SS
133.0358.053 Hot valve 3794R-H
133.0358.055 Cold valve 3794R-C
133.0251.356 Base plinth Chrome 3734R CH
133.0251.358 Base plinth SilkSteel 3734R SS
133.0150.221 Fixing kit 3311R
133.0251.361 Flexi-tails 3728R

Franke UK Limited
West Park, MIOC
Styal Road
Manchester
M22 5WB
Tel: [phone]
Fax: [phone]
Email [e-mail]
For spare parts, servicing or any other queries,
visit www.franke.co.uk
Guarantee
Your Franke mixer has been manufactured to the high
standard you would expect of any Franke product but in the
unlikely event that you should experience any defect in the
materials or workmanship within one year of purchase, we will
replace the faulty part free of charge. This is provided the
mixer has only been used for normal domestic purposes in the
UK and that the care, installation and maintenance
instructions have been observed.
You should also retain your dated invoice as proof of purchase
to validate any claims under our guarantee.
This one year guarantee is extended to five years in the case
of the valve mechanism.
Normal wear and tear is excluded from the guarantee.
Decorative surface finishes are guaranteed for one year from
the date of purchase provided our advice concerning care has
been observed and no scouring agents have been used.
Scuffs and scratches caused by improper installation or
accidental damage are not covered by this guarantee.
Neither are slight shade variations or any damage or defect
caused by incorrect installation or abuse of the fitting.
Service
For spare parts, servicing or any other queries,
visit www.franke.co.uk
Optional tap brace
A large or heavy tap fitted to a stainless steel inset sink may
occasionally flex the sink. To counteract this, Franke has
developed an innovative tap brace that can be purchased
separately. The tap brace connects the tap to the worktop and
not just to the sink, offering additional support to the tap and
much more stability when fitted. The tap brace has a variable
collar to ensure it will fit most models of tap and can be used
on any inset stainless steel sink.
The Franke tap brace is available on request from most
kitchen retailers.