FRENZEL SE6L6 User manual

Frenzel Tube Amps
2011 Copyright by Frenzel Tube Amplifiers. All rights reserved. All designs, technical data, pictures, and information are
copyrighted and may not be reproduced without the permission of Frenzel Tube Amplifiers.
` Page 1
Owners Manual
STEREO POWER AMP
MODEL SE6L6

Frenzel Tube Amps
2011 Copyright by Frenzel Tube Amplifiers. All rights reserved. All designs, technical data, pictures, and information are
copyrighted and may not be reproduced without the permission of Frenzel Tube Amplifiers.
` Page 2
FRENZEL
FRENZEL FRENZEL
FRENZEL STEREO SE6
STEREO SE6STEREO SE6
STEREO SE6L
LL
L6
66
6 POWER AMPLIFIER
POWER AMPLIFIERPOWER AMPLIFIER
POWER AMPLIFIER
The FRENZEL Stereo SE6L6 Stereo Power Amp was designed for the tube purist to be
used as a musical instrument power amp or as a home stereo power amp. It uses an all
tube circuitry including a tube rectifier. Two 12AX7/E 83 tubes are used as preamp
buffer drivers. The output uses a lass A single-ended 6L6 design with cathode bias for
each channel. This design allows the use of many of the octal base output tubes
including the 6V6, 6L6, 5881, 6550 and EL34. It will give crystal clear tones and will
faithfully reproduce what you put into it.
SPECIFICATIONS:
RMS POWER – 6L6 12 watts per channel
Output Impedance: Selectable 4Ω, 8Ω, or 16Ω each channel
C annel Sensitivity: 1.0 Vrms for full output (full volume per channel)
Preamp Tubes: 2 – 12AX7 (input driver/buffer)
Power Amp Tubes: 2 – 6L6 (1 per channel)
USA Model: 120VA , 300VA, Export Model: 230VA , 300VA
Control Panel Dimensions: 3.5" High x 19" Wide (2 rack spaces)
Vent Panel Dimensions: 3.5" High x 19" Wide (2 rack spaces)
C assis Dimensions: 17” Wide x 10” Deep X 2” High
Cabinet Dimensions: 21” Wide x 13” Deep x 9” High
Net Weig t: 30 lbs
Price: $ 1095.00

Frenzel Tube Amps
2011 Copyright by Frenzel Tube Amplifiers. All rights reserved. All designs, technical data, pictures, and information are
copyrighted and may not be reproduced without the permission of Frenzel Tube Amplifiers.
` Page 3
FEATURES:
Input Jacks isolated from chassis for low noise, eddy currents, and hum.
Laser Etched Faceplate
lassic hicken Head Knobs, Toggle Switches and Jewel Pilot Light
D on filaments for low 60 hz hum.
Star ground system to reduce induced current chassis noise.
Input Level ontrols for each channel
lassic Type 5F6A Style Presence control.
Unique NNFB "Edge" switch on the PRESEN E control that transforms the power amp section into a No-
Negative-Feedback style amp for more open, less compressed tones.
Post output transformer LINE OUT with LINE OUT LEVEL control for driving a higher power amp, or for
using this amp as a tube preamp/overdrive or recording, Auto switching internal load if speaker is not
connected to give you loaded output distortion.
IE detachable plug-in three prong grounded power cord.
STANDBY switch to turn off the plate voltage during warm-up.
Rock solid point-to-point hand wiring using only the best of parts...low noise tubular polypropylenes caps,
metal film resistors, ceramic sockets, switchcraft jacks...etc.
Tube compliment: The amp comes with 2 - 12AX7, 2 – 6L6, 1 - 5U4, but you can substitute 12AT7's or
12AU7's in the preamp/driver for different tones and overdrive sounds. You can also substitute 6V6,
5881's, KT66's, KT88's, 6550's, or EL34's in the output stage for different sounds.
FRONT PANEL:
C annel 1 Controls
- LINE OUT LEVEL
- INPUT LEVEL
- PRESEN E with NNFB PULL SWIT H
Power Controls
-STANDBY SWIT H
- PILOT LIGHT
- POWER SWIT H

Frenzel Tube Amps
2011 Copyright by Frenzel Tube Amplifiers. All rights reserved. All designs, technical data, pictures, and information are
copyrighted and may not be reproduced without the permission of Frenzel Tube Amplifiers.
` Page 4
C annel 2 Controls
- LINE OUT LEVEL
- INPUT LEVEL
- PRESEN E with NNFB PULL SWIT H
REAR PANEL:
C annel 1 Controls
- IMPEDAN E SELE TOR
- SPEAKER OUT JA K
- LINE OUT JA K
- INPUT JA K
Power Section
- POWER ORD ONNE TOR
- FUSE
C annel 2 Controls
- IMPEDAN E SELE TOR
- SPEAKER OUT JA K
- LINE OUT JA K
- INPUT JA K
User’s Operation Guide:
FRONT PANEL CONTROLS:

Frenzel Tube Amps
2011 Copyright by Frenzel Tube Amplifiers. All rights reserved. All designs, technical data, pictures, and information are
copyrighted and may not be reproduced without the permission of Frenzel Tube Amplifiers.
` Page 5
LINE OUT LEVEL – ontrols the output level of the Line Out jack on the rear panel of the amp.
LEVEL- ontrols the amount of signal sent to the power amp from the driving preamp. Sets the output
level of the amp. Start with this control all the way down. Make sure the preamplifier is connected and
turned on and it’s output level turned up. Bring the amplifier volume upto the desired loudness. You will
need to experiment to get the correct volume balance between the preamplifier output and the amplifier
output level. Ideally the amplifier LEVEL should be turned up at least one half with the knob indicator
lines running vertical.
PRESENCE – boosts the high frequency range and gives the amp more bright punch. Set at ½ for initial
setting. (Please note that a slight scratchy noise is normal as the Presence control is adjusted. This is
caused by the D cathode current running through the contacts. It only occurs when the control is
adjusted and does not affect the operation of the amp.)
EDGE PULL SWITCH (part of Presence control) – when pulled out turns off the negative feedback in the
amp which produces a boost in the volume and a more dynamic less compressed tone.
POWER SWITCH – turns power ON to filaments of tubes. Pilot lamp will light up when switch is turned to
ON (up) position.
STANDBY SWITCH – turns ON high voltage to tubes. Allow tubes to warm up 1-2 minutes before turning
to ON (up) position. This protects tubes and lengthens tube life. Turn to OFF position(down) when amp
temporarily not in use.
PILOT LAMP – lights up when Power switch is turned on.
REAR PANEL CONTROLS:

Frenzel Tube Amps
2011 Copyright by Frenzel Tube Amplifiers. All rights reserved. All designs, technical data, pictures, and information are
copyrighted and may not be reproduced without the permission of Frenzel Tube Amplifiers.
` Page 6
C annel 1 and C annel 2 Controls
IMPEDANCE SELECTOR – selects the output impedance for the speaker to 4 – 8 -16 ohms. Set the switch
to match the impedance of the speaker.
SPEAKER JACK – a 1/4" unbalanced jack connects output of amp to speaker.
LINE OUT JACK - is a post output transformer 1/4" unbalanced jack LINE OUT jack. Works with LINE
OUT LEVEL control on Front Panel. an be used for driving another amp, mixer , recorder etc. It can be
used without a speaker plugged into the amp. There is an internal load connected by a switch on the
speaker jack if a speaker is not plugged in. This internal load simulates the speaker and will give you
loaded clean and output distortion tones.
CHANNEL INPUT JACK – a 1/4" unbalanced jack is used to connect the signal to each of the amplifiers
channels. Plug output of preamp into this jack.
Power Section
FUSE - protects the power supply. Use a 3 amp SLO-BLO type fuse.
POWER CORD – a detachable power cord connects power to the amp. Make sure that the cord is fully
seated in the connector. The power cord is a three prong grounded cord. Always plug into a grounded
outlet to prevent electrical shock. The line voltage is shown over the power cord bushing. Be sure that
the voltage matches your line voltage.
TUBE LAYOUT CHART
12AX7
12AX7
V2 – DRIVER V1 - DRIVER
6L6 6L6
V3 – OUTPUT V4 – OUTPUT
5U4
V5 – RECTIFIER