Freund Fermax iLOFT User manual

BY
INDEX
iLOFT MONITOR................................................................................................... 4
Installing the Monitor................................................................................... 4
Available Functions:.................................................................................... 5
Wiring.......................................................................................................... 6
Programming the monitor ........................................................................... 7
- Option 1: From Panel + Monitor.......................................................7
- Option 2: From the Monitor............................................................... 7
Programming: Administrator Menu ............................................................. 9
- Access the Administrator Menu........................................................9
- Programming the Monitor from the monitor itself............................. 9
- Automatic Opening (Doormatic) ..................................................... 10
- Conversation Mode Configuration.................................................. 11
- F1 auxilliary Function...................................................................... 11
- F2 auxilliary Function......................................................................12
Adjustments: Audio + Video:..................................................................... 13
- Video: Brightness - Contrast - Colour............................................. 13
- Audio............................................................................................... 14
Programming: User Menu......................................................................... 16
- Melody Selection............................................................................ 16
* 1. Main Panel .......................................................................... 16
* 2. Secondary Panel................................................................. 17
* 3. Doorbell............................................................................... 17
- Do no disturb (Cancel Ringtones) ..................................................17
- Automatic Opening (Doormatic) ..................................................... 17
iLOFT Monitor........................................................................................... 19
- Buttons ........................................................................................... 19
- Operation........................................................................................ 20
Maintenance (cleaning)............................................................................. 22
Technical Characteristics .......................................................................... 23
Page 3
EN

BY
INSTALLING THE MONITOR
Monitor Dimensions (Height x Width x Depth*):
197 x 131 x 60 mm / 7.7” x 5.1” x 2.3”
Pure model Monitor Dimensions (Height x Width x Depth*):
197 x 131 x 59 mm / 7.7” x 5.1” x 2.3”
Fermax Box Dimensions (Height x Width x Depth):
158 x 108 x 45 mm / 6.2” x 4.2” x 1.7”
Universal Box Dimensions (Height x Width x Depth):
174 x 114 x 50 mm / 6.8” x 4.5” x 2”
Note:
- this monitor can be installed in a universalbox.
- Depth * : the Monitor depth stated here takes into
account the Fermax box
Pag 4
14mm
131mm
F2
F1
XXmm
MENU
197mm
1
(*) Remove the electrostatic protectivetag
(*)
(*)
3
2a Installation with a FERMAX BOX
(*) Remove the electrostatic protectivetag
(*)
(*)
3
2b Installation with a UNIVERSAL BOX

BY
MONITOR INSTALLATION SURFACE
Monitor Dimensions (Height x Width x Depth):
197 x 131 x 34.3 mm / 7.7” x 5.1” x 1.3”
Pure model Monitor Dimensions (Height x Width x Depth):
197 x 131 x 33.3 mm / 7.7” x 5.1” x 1.3”
Available functions
The available functions on the iLoft VDS monitor are summarised in the list below:
- Command-based opening of door
- Call to guard
- Call volume regulation
- Call disconnection (Do not disturb)
- Ringtone selection (7 options)
- Doorbell
- Programming via the terminal and via the entry panel
- Input audio volume adjustment
- Configuration of parameters for the screen menu (OSD)
- Automatic door opening (DOORMATIC)
- Lift control
- Image adjustments (brightness, contrast and colour) Page 5
34,3mm
131mm
F2
F1
MENU
197mm
1
(*) Remove the electrostatic protectivetag

BY
-
L
2 OUTPUTS VIDEO DISTRIBUTOR
2 OUTPUTS VIDEO DISTRIBUTOR
Connection
Video terminals (coaxial) 
V: live
M: mesh
Ct :CameraActivation(11Vdc)
 Connection terminals:
+, - : 18 Vdc power supply
L: data bus
F1, F2: additional functions. See the chapter on
programming
T, -: call button connection for residential Door ( P1 )
A,: c all extension connection ref. 2040, light and bell
activator ref. 2438, etc...
F2 F1 T A
Ct -
L + M V V M V
M
DISTRIBUIDOR VIDEO 2 SALIDAS
2 OUTPUTS VIDEO DISTRIBUTOR
+
+ R 15 (-) 2 6
75 Ohm L -
P1
V M V M +18
4 3
V M V M
R1
75
M V V M
75 Ohm
Detail of connection of
the video cables onthe
monitor connector
L - +MV
Pag 6
Detail of connection of the VIDEO cables
on the monitor connector (1) when there is
another monitor connected (2)
M V V M
+
M
+
75 Ohm
F2 F1 T A Ct - L + M V V M
F2 F1 T A Ct - L + M V V M
REF.2448 DISTRIBUIDOR VIDEO 2 SALIDAS
- L + M V
+
+
75 Ohm
P1
P1
-L + COAX
M V V M Detail of connection
of the COAXIAL atthe
75 Ohm monitor connector
2
F2 F1 T A Ct - L + M V V M
1
F2 F1 T A Ct -
REF.2448 DISTRIBUIDOR VIDEO 2 SALIDAS
M
Ct:
L
+
75
L
V M V M +18
4 3
V M V M
R1
-
75 Ohm
2 6
5
(-)
R 1
P1
75 Ohm
F2 F1 T A Ct - L + M V V M
V
P1
P1
V M V M +184 3 V M V M
R1
75
L
-
2 6
5
(-)
R 1
V
L + M V V M
REF.2448

BY
PROGRAMMING THE iLOFT MONITOR
The monitor will not function until it has been programmed.
Option 1: From Panel + Monitor
< 2 min. 30 sec.
1º. With the monitor connected, press the programming button «PROG » for 2
seconds (to access this, you must lift up the front cover).Aconfirmation tone will sound.
2º. Press the call-to-residence button. Again a confirmation is made with a different call tone.
Note: The time between steps 1 and 2 must be less than 2 and half minutes.
Option 2: From the Monitor You can program the monitor via the on-screen menu.
1º. Enter in the User menu. Press «Menu» 1 second.
User Menu
Note: If the monitor is not yet programmed, press
«Menu» for 1 second, and directly access the
«ADMINISTRATOR Menu», see the next page.
(*) Function available depending on model.
Page 7
(*)
2
1
2 secs
MENU
1"
1

BY
2. When in the User menu, enter inADMINISTRATORmenu (pressing F1 + F2 simultaneously
for 5 seconds). Once in the ADMINISTRATOR menu, select the first option.
Select the first option:
The icons viewed on-screen are controlled
via the corresponding buttons on the monitor.
The first thing the monitor then does is indicate the
number of the current monitor on the SCREEN. If it is not
programmed, it will show the following: - - -
Note: When the terminal has not been programmed the
blue led will flash very slowly.
3º. Programme the call number: Each time the button
corresponding to hundreds, tens or single units is
pressed, the figure goes up that figure and is shown
on the DISPLAY.
a) Hundreds: Press the button
b) Tens: Press the button
c) Single unit:Press the button
Once you reach 9, if you press it again,
it returns to 0. The next time you press, it
will start at 1.
4º. Exit Programming: Press the «OK» to confirm the selected number. You return to the
previous programming menu.
Pag 8
Administrator Menu
+
F1 F2
5"
2
a
b
c

BY
(*)
PROGRAMMING: ADMINISTRATOR Menu
Access the Administrator Menu
1º.Enter in the User menu. Press «Menu» 1 second.
User Menu
Confirmation key
Scroll keys in the menus
Cancel key Menu exit key
2. When in the User menu, enter inADMINISTRATORmenu (pressing F1 + F2 simultaneously
for 5 seconds). Once in the ADMINISTRATOR menu, select the first option.
Administrator Menu
The icons viewed on-screen are controlled
via the corresponding buttons on the monitor.
From this menu you can access the different options and functions shown with the icons.
Programming the Monitor from the monitor itself
Explained on the previous page.
(*) Function available depending on model.
Page 9
Icons
MENU
1"
1
+
F1 F2
5"
2

BY
Activated
Automatic Opening (Doormatic)
The automatic open function is disabled by default (not
availble to the user) and the installer must enable it, if
desired, from the administrator menu, accessing the
specified option.
By selecting this option you can access the submenu that allows you to enable or disable
the doormatic mode.
Deactivated you can enable the doormatic
mode by pressing the right arrow the left arrow disables the door-
matic mode
Notes:
- If activated or not, the doormatic option is available or not available in the user menu.
- There is also an option to connect a timer to the doorbell (if this is not being used) so that
the automatic opening function is activated and deactivated each day at certain times. If
that entrance is activated for a period of greater than 30 seconds it determines that the
automatic door function should be activated. When this doorbell feature is deactivated
this function will also be deactivated.
User Menu: Doormatic function
DISABLED by the installer User Menu: Doormatic function ENABLED by the installer
Pag 10
(*) Function available depending on model.
(*)
(*)

BY
by
panic call mode
Conversation Mode Configuration
Within the conversation menu, you can select the Simplex
and Hands free mode.
The hands free mode is selected as default.
Simplex Mode: press the audio activation button to talk,
«MENU» button, and release to listen.
Hands free you can select the simplex mode Simplex mode
by pressing the right arrow the left arrow disables the
simplex mode
F1 auxilliary Function
The F1 key and connection allow you to configure the
operating mode. You can select between the Negative
send mode (output) and SOS to MDS Guard unit (input).
Initially configured by default as an output, and sends
a negative.
Ifthe other option is selected in conjunction with an MDS/
VDS decoder (version V10.26 or above) a panic alarm
can be sent to the MDS guard unit. Upon pressing F1
the corresponding command is sent by the bus. The F1 connection also acts as an input, so
when connecting a keypad to this, pressing it it also sends the panic command to the MDS
guard unit.
negative send mode you can select the panic mode
pressing the right arrow the left arrow disables the
panic call mode.
Note: If configuring the Day Panic mode on the Guard unit, it automatically configures the
Panic Call mode on the monitor/s. Upon deactivating the mode on the guard unit, it
also deactivates it on the monitors. Page 11

BY
F2 auxilliary function
The F2 key and F2 connection allow you to configure
the operating mode.
Initially it is configured, by default, as an output for F2
when the F2 key is pressed.
However, you can configure the Lift Control option,
giving an output to the F2 connection when sending the
Lock-Release, either for the time the lock-release button
is being pressed in call or conversation mode or while
the doormatic automatically sends the lock-release command. If you press the F2 button,
no action occurs.
F2 output mode you can select the lift control lift control mode
mode by pressing the right arrow the left arrow disables the lift
control mode
Resetting the Parameters
You have the option to reset the parameters to default
values by selecting the option on the installation menu
and confirming the operation.
This reset does not change the programmed terminal´s
number.
The parameters changed are:
- Selected melody for the main panel. Ding-Dong-Dang.
- Selected melody for the secondary panel. Bitonal
Fermax.
- Selected melody for the doorbell. Ding-Dong.
- Call tone volume medium. Call volume
- Conversation volume. Medium conversation volume
- Image adjustments (brightness, contrast and colour).
Start-up adjustments.
- Do not disturb deactivated
- F1 connection operations. Panic OFF.
- F2 connection operations. Lift Control OFF.
- Doormatic. Disabled.
Cancel:
Accept