Frigidaire FGHD2471KB - Gallery Premier - 24"... User guide

Trouble Shooting TipsExploded View of Wash System
Tub and Door Seal
The door seal is pressed into the tub channel for
an interference fit. To install the seal, locate the
center mark on the seal back and press into
ProductSpecifications
Electrical
Rating...................................120 Volts, 60Hz
Separate Circuit..15 amp min.- 20 amp max.
Motor (Amps) ........................................... 1.8
Heater Wattage.......................................900
Total Amps (load rated)......................... 10.0
TempAssure .............................. 140°F ±5°F
(60°C±3°C) [with outer door in place]
TempBoost.............145°F ±5°F (63°C ±3°C)
Heated Wash/Heated Rinse
Sanitize ..................150°F ±5°F (66°C ±3°C)
Hi-Limit Thermostat ................ 200°F (93°C)
Water Supply
Suggested minimum incoming water
temperature............................. 120°F (49°C)
Pressure (PSI) min./max.................... 20/120
Connection (NPT) ..................................... 3/8"
Consumption (Normal Cycle).......................
.............4.9 - 9.7 U.S. gal., 18.5 - 36.7 liters
Water valve flow rate (U.S. GPM)........... .83
Water recirculation rate (U.S. GPM)..............
.................................................... approx. 12
Water fill time.....................................87 sec.
To replace dispenser:
• shut off electricity to dishwasher,
• remove outer door panel assembly,
• disconnect wiring to the actuator,
• remove the six screws,
• remove the dispenser,
• replace and reinstall screws,
• rewire actuator.
Check the Following
1. Fuse (blown or tripped).
2. 120 VAC supply wiring connection
faulty.
3. Electronic control board defective.
4. No 12 VAC power to control.
5. Motor (inoperative).
6. Door switch (open contacts).
7. Door latch not making contact with
door switch.
8. Touch pad circuit defective.
9. No indicator lamps illuminate when
STARTorOPTIONSarepressed.
1. Motor(badbearings).
2. Motor stuck due to prolonged
non-use.
1. Improper voltage.
2. Motor windings shorted.
3. Glass or foreign items in pump.
1. Heaterelement(open).
2. Electronic control board defective.
3. Wiring or terminal defective.
4. Hi-Limit thermostat defective.
1. Latch mechanism defective.
2. Electronic control board defective.
3. Wiring or terminal defective.
4. Broken spring(s).
5. Defective actuator.
1. Drain restricted.
2. Electronic control board defective.
3. Defective drain pump.
4. Blockedimpeller.
5. Openwindings.
6. Wiring or terminal defective.
1. Water supply turned off.
2. Defective water inlet fill valve.
3. Check fill valve screen for
obstructions.
4. Defective float switch.
5. Electronic control board defective.
6. Wiring or terminal defective.
7. Float stuck in “UP” position.
1. Drain hose (high) loop too low.
2. Drain line connected to a floor drain
not vented.
1. Detergentallowedtostandtoo longin
dispenser.
2. Dispenser wet when detergent was
added.
3. Detergentcoverheldclosedorblocked
by large dishes.
4. Improperincomingwater
temperature to properly dissolve
detergent.
5. See "Detergent cover will not open."
Always disconnect the dishwasher from the electrical power source before adjusting or
replacing components.
Personal Injury Hazard
isattachedbyawormgearclamptothedischarge
end of the drain pump.
The drain hose must have a loop at a
minimum
height of 32 inches
in order to insure proper
drainage.
The main pump can easily be removed by
disconnecting the upper spray arm supply tube
hose,thedrain pump connector hose,the wiring
harness connections made at the circulation
motor, the water heat thermistor located on the
bottom of the pump and rotating the four sump
retainers toward the middle of the sump.
PumpAssembly
The pump assembly is driven by a synchronous
motor. Rotation is in the counterclockwise
directionat 3600RPM. Themotor drives apump
which supplies 100 percent filtered water at a
rate of approximately 12 GPM to one spray arm
atatime.The sprayarm’soperationisalternated
by small “pauses” of the motor during the wash
cycle.
Draining is accomplished by using a small
separate synchronous drain pump mounted to
the side of the sump. The drain pump is
connected to the main pump by a small rubber
hose. The drain check valve is located at the
dischargeend ofthe drainpump. Thedrain hose
Short Turn
Gasket Cross Section
DetergentandRinseAidDispenser
The detergent and rinse aid dispenser is a one
piece component consisting of a molded
detergent cup and a built-in rinse aid dispenser.
The detergent cup has a spring loaded cover
and the rinse aid dispenser has a removable
cover.
Liquid rinse aid is added to the dispenser up to
the fill line indicator. The amount of rinse aid
released can be adjusted by turning the arrow
indicator from one, being the least amount, to
four, being the greatest amount.
Mounting
Rib
Tub
Interior
Remedy
1. Replace fuse or reset breaker.
2. Repair or replace wire fasteners at
dishwasher junction box.
3. Replace control board.
4. Replace control board.
5. Replacemotor/impellerassembly.
6. Replace latch assembly.
7. Replace latch assembly.
8. Replace console assembly.
9. Replace console assembly.
1. Replace motor assembly.
2. Rotatemotorimpeller.
1. Check voltage.
2. Replacemotor/impellerassembly.
3. Clean and clear blockage.
1. Replace heater element.
2. Replace control board.
3. Repair or replace.
4. Replacethermostat.
1. Replacedispenser.
2. Replace control board.
3. Repair or replace.
4. Replacedispenser.
5. Replacedispenser.
1. Clear restrictions.
2. Replace control board.
3. Replacepump.
4. Check for blockage, clear.
5. Replacepumpassembly.
6. Repair or replace.
1. Turn water supply on.
2. Replace water inlet fill valve.
3. Disassemble and clean screen.
4. Repair or replace.
5. Replace control board.
6. Repair or replace.
7. Clean float.
1. Repair to proper
32-inch minimum
height
.
2. Install air gap at counter top.
1. Instruct customer/user.
2. Instruct customer/user.
3. Instruct customer/user on proper
loading of dishes.
4. Incoming water temperature of
120°F is required to properly
dissolve dishwashing detergents.
Symptom
Dishwasherwillnot operatewhen
turnedon.
Motor hums but will not start or run.
Motortripsoutoninternalthermal
overloadprotector.
Dishwasherrunsbutwillnotheat.
Detergent cover will not latch or
open.
Dishwasherwillnotpumpout.
Dishwasher will not fill with water.
Dishwasherwatersiphonsout.
Detergentleftindispenser.
Standard Dry Air Flow
Whenthecontrol advancestothe “dry”portionof
the cycle, a vent actuation solenoid is closed.
Thisopensthevent valve and startstheventfan
bothlocatedinthe toprightrearcornerof thetub.
The fan draws in the air from outside the tub,
forcing the hot, humid air down and out the
020905
TUB
TUB
TUB
TUB
Lower
Spray Arm
Middle
Spray Arm
Assy.
3rd Level
Spray Arm
Assy.
Delivery
Tube
Soil
Director
Volute
Cover
Check
Ball
Glass
Trap Spray Arm
Support
Soil
Filter Filter
Sump
Housing
Sump
Gasket
Heating
Element
Water
Bottle
Water
Valve
Water
Inlet Tube
Circulation
Motor
Motor
Bracket Drain
Pump
bottom of the outer door panel. This outside,
cooler, dryer air helps to speed evaporation of
water from the hot dishes. At the same time the
heatingelement is continuallycycledon andoff.
On some models the dry portion of the cycle can
be extended to improve drying performance.
place. Next, install the bottom of the seal by
creating a short turn at the bottom of the tub
channel and ensuring the seal extends to the
locatorridgeat the bottomof the tub. Then align
andgently pressthe sealintothe channelin only
a few spots. Next, close and latch the door to
allowthegaskettoseat properlyintothechannel.

Hall sensor
Cycle Selection Options
SERVICE DAT
ASHEET
P/N: 154768201
E
lectronic Series
BK.......................... Black
BU............................Blue
PK............................Pink
R...............................Red
R-BK...............Red/Black
W............................White
Wiring Diagram
Display Codes (LED)
To sta rt
To del ay st art
Close and latch door. Press START/CANCEL pad.
Close and latch door. Press DELAY START pad to
select desired delay time.
To sel ect a n ew
cycle or option Press desired cycle and/or option pad. The indicator
lights will change. Press START/CANCEL within 15
seconds to begin cycle.
To can cel c ycl e Press START/CANCEL. Dishwasher will drain for
90 seconds, then shut off.
For controls
lock ...........
Press and hold the RINSE ONLY or AIR DRY
pad for 3 seconds. To unlock, press and hold the
RINSE ONLY or AIR DRY pad for 3 seconds.
SENSING
WASHING
SANITIZED
DRYING
CLEAN
OPTION LED's Flashing
STATUS LED's Flashing
----------------------Turbidity sensor is checking the condition of the wash/rinse water.
No sensing for LIGHT WASH (UPPER RACK), LIGHT WASH (LOWER RACK) and CHINA/CRYSTAL.
----------------------Wash portion of cycle.
--------------------The SANITIZED criteria has been met. Indicator light will switch off when door is opened.
------------------------ Drying portion of cycle.
------------------------ Shows completion of cycle. Indicator light will switch off when door is opened.
-- HI-TEMP WASH and NO HEAT DRY/POWER DRY OFF LED's flashing indicates power failure has
occurred. Press START/CANCEL pad and reselect desired options and cycle.
-- The STATUS LED's that are lit when the door is opened will flash. Close door.
RINSE AGENT LOW ------- The liquid rinse agent is low. Light will switch off after 5 complete wash cycles or dispenser is
filled.
This information is intended for use by persons having electrical and mechanical training and a level of knowledge of these subjects generally considered acceptable in the appliance repair trade. Electrolux Home Products North America cannot be responsible,
nor assume any liability, for injury or
damage of any kind arising from the use of this Service Data Sheet.
Operation
or LO..Low liquid in the rinse aid dispenser
..........A power failure has occurred
.........Water heating delay
..........Close and latch the door
ER/ER....Switch Failure
....Hour(s) delay before start
PF
HO or Hd
CL
'01-24'
ER/CE....Configuration Error
ER/uo.....Vent will not close
ER/uF.....Fan not running
PUMP MOTOR
DRAIN MOTOR VIO
120VAC
60HZ
USER INTERFACE SWITCH
ELECTRONIC CONTROL BOARD
P3-2
P6
BU
DISPENSER R-Y
WP3- 3
W W
HEATER W
HI-LIMIT
THERMOSTAT
TURBIDITY SENSOR/
THERMISTOR
RP1
WATER VALVE
FLOAT
SWITCH PK P3- 1
W
Y
P3-7 P3-8
RINSE AID
LEVEL SENSE
BK BK P2- 8
P2- 7
P3-4
P-5
P3-6
DOOR
SWITCH
W
NEUT W L1 BK
BK BK
P3-5
P1
BK
P2-1
W
P2-2
R
P2-3
W
The water/service test is a
special function initiated from
the power failure mode or idle
mode.
While in power failure or idle
mode - simultaneously press the
DRY/AIR DRY and
START/CANCEL pads for 3
seconds.
The dishwasher will then step
through the test cycle per the chart.
Pushing the START/CANCEL pad
will advance the dishwasher to the
next step.
Water/Service Test
27
45
0.4
75
60
90
90
447
60 1
1
0
0
0
0
0
0
0
0
1
1
1
0
0
0
0
0
0
0
0
1
1
0
0
0
1
1
1
0
X
1
1
0
0
0
1
0
0
0
1
1
1
1
1
0
0
0
0
0
1
00
0
0
0
0
0
0
1
0
0
0
0
0
0
1
0
0
0
1
1
1
0
0
0
0
0
1
1
2
3
4
FILL/DISPENSER
STEP TOTAL TIME (SEC) WATER VALVE CIRCULATION MOTOR DRAIN MOTOR HEATER DISPENSER FAN UNIT SENSING LED WASHING LED SANITIZED LED DRYING LED
CLEAN LED
FILL
WASH/HEAT
PAUSE
WASH/HEAT
WASH/HEAT/DISP.
DRAIN
DRY
TOTAL
CLEAN LED stays on until door is opened or cycle is started.
X - denotes selectable option
5
6
7
8
0
0
0
0
0
0
1
0
(Some models)
(Some models)
0
0
0
0
0
0
P2- 4
P2- 5 P2- 6
BK
W
R
HALL SENSOR
DISPLAY
Y/BL P2-13
P2-12
BK-W
P2-11
R
P32-6
BK
P32-9
FAN DRY UNIT
R-W
RINSE LED
SENSING LED
0
0
0
1
1
0
0
0
1
RINSE LED
Device being monitored
0
0
0
1
1
0
0
0
1
0
0
0
1
1
0
0
0
1
0
0
0
1
1
0
0
0
1
0
0
0
1
1
0
0
0
1
0
0
0
1
1
0
0
0
1
0
0
0
1
1
0
0
0
1
0
0
0
1
1
0
0
0
1
Fan damper
Display flashes when Detection of failure
0
0
0
1
1
0
0
0
1
0
0
0
1
1
0
0
0
1
0
0
0
1
1
0
0
0
1
0
0
0
1
1
0
0
0
1
0
0
0
1
1
0
0
0
1
0
0
0
1
1
0
0
0
1
0
0
0
1
1
0
0
0
1
0
0
0
1
1
0
0
0
1
Turbidity
Fan speedFan speed
Rinse aid
Thermistor
Uo
Tu
HS
UF
HS
Th
RA
Color Code
Display Codes (Readout)
Y-BK.............Yellow/Black