Frigidaire FDR30NGDC User manual

Grill Assembly
Built-In Instructions ........... 5-12
Gas Requirements
Leak Testing ................. 13-15
Using the Grill
Rotisserie/Side Burner Usage ........... 16-19
Lighting the Grill ................. 17
Care & Maintenance ............. 20
Before You CaJm
Trouble Shooting ............. 21-22
Visit the Frigidaire Web Site at:
http ://www.frig idai re.corn Warranty .......................... 23
READ AND SAVE THESE iNSTRUCTiONS =MADE IN THE U.S.Ao FD301MDEN 1/04

i aS¸¸¸¸¸¸U /;
Congratulations on your purchase of a new gas grill! At Electrolux Home Products, we
are very proud of our product and are completely committed to providing you with the
best service possible. Your satisfaction is our number one priority.
We know you'll enjoy your new gas grill and Thank You for choosing our product. We
hope you consider us for future purchases.
PLEASE CAREFULLY READ AND SAVE THESE INSTRUCTIONS
This Use & Care Manual provides specific operating instruction for your model. Use your
gas grill only as instructed in this manual. These instructions are not meant to cover every
possible condition and situation that may occur. Common sense and caution must be
practiced when installing, operating and maintaining any appliance.
Questions? 1-800-320-0859
Please record Grill information for future reference and service work:
Model #:
Serial #:
Date of Purchase:
Gas Type:
Please retain this manual tbr thture reference
6) 2004 Electrolux tlolne Products, lnc All rights reserved

IMPORTANT SAFETY INFORMATION
-Read this manual carefully before using your grill to reduce the risk of fire, burn hazard or
other injury.
- Extreme cam should be used because of the high temperatures produced by this appliance. CHILDREN SHOULD NOT BE LEFT
UNATTENDED IN AN AREA WHERE THE GRILL IS BEING OPERATED.
- This appliance must be kept clear from combustible materials, gasoline or other flammable vapors and liquids. Do not allow
flammable materials to come in contact with grate, burner or hot surfaces.
- Do not repair or replace any part of this appliance unless it is specifically recommended in this manual. A qualified service techni-
cian should conduct all other service.
-Follow the installation and servicing instructions provided with this product. Have your grill installed by a qualified service techni-
cian. Locate the main gas supply valve so that you know how to shut the gas off to your grill. If you smell gas, make sum all gas
connections are tight before operation. If you continue to smell gas call a qualified technician.
- When lighting a burner, always pay close attention to what you am doing. Be certain you are pushing the ignitor that lights the
burner you intend on using.
2

5
6
9
13
14
10
12
11
.
2.
3.
Roll top grill hood
Grilling/Cooking surt:ace
Side Shelf
.
9.
10.
Warming shelf
Infrared back burner
Electronic ignitor: main, rear infrared
& side burner
4. Control knob: back infrared burner 11. Cart w/doorr
.
6.
Control knobs: main burners
Convection vents
12. Ignitor access opening
13. Side Burner
7. ttandle 14. Control knob: Side Burner

Cart Parts
2 L-shaped side pieces
1 U-shaped back side piece
1 Base
2 Wheel channels
Part #'s
WIP- 192-71 D384
WIP- 192-72D384
WIP- 192-70D304
WIP- 192-438365L/R
Cart
1
1
1
Door Parts
Door handle kit
Nylon bushing
Door pivot screw and nut
RMP-122-00921
RMP-122-00520
RMP- 122-00598/122-00508
Grill Parts
1
1
1
1
5
3
1
1
1
1
Stainless steel grill head
Stainless steel side shelf
Side burner (side shelf)
Electronic ignitor
Flavor grids
Stainless steel bar grates
Stainless steel warming rack
Drip pan
Magnetic catch
Hose and regulator (LP models only)
Grill Parts
WIP-122-11D304
WIP- 192-326393
WIP- 191-43DGN4
RMP-122-53306
WIP-191-13D384
RMP-122-00699
WIP-191-538015
RMP-122-00005
RMP-122-00029
RMP-122-00821
Assembly Parts
14 Hex head screws
8 Bolts
1 Rubber Door Stop with Bolt
1 1 1/4" Plastic Plug
Assembly Parts
RMP-122-00615
RMP-122-00626
RMP-122-00579
RMP- 122-00492

Note: Prior to assembly remove protective film from stainless steel parts
Fig. 1
Wheel Channel
Cart Assemblw Door Stops & Door Pivot Bolts
1. Attach the two L-shaped sides to the back portion
of the cart, making sure the two holes face up &
the key holes are on the top, using the (4) self
tapping hex head screws. (See Fig. 1)
Note: Apower screwdriver is required to install the
screws-be cautious not to over-tighten and strip
the screws.
.Set the base on the top of the cart assembly, with
large opening closer to back portion of cart, and
align the eight mounting holes. Then set the 2
wheel channels on the base and attach them using
the (8) bolts provided, from inside the cart
upwards through wheel channels. (See Fig. 2)
Note: Tighten the bolts securely
3. Door Stop: Insert Door Stop Bolt downward
from bottom side of Cart Base through the hole
found in the right/front of the base. (See Fig 3)
.Screw Rubber Cap onto Bolt from the topside of
Cart Base and tighten securely. (See Fig 4)
.Door Pivot Bolt: Insert Bolt downward from
bottom side of Cart Base through the hole %und
in the left/front of the base and secure with
bolt. (See Fig. 2)
Fig. 4
Fig. 2
Fig. 3

Attaching Grill Head to Cart
1. While keeping the Grill on the foam base
lean it onto its back. (be sure to hold the
hood shut when doing this.) With the Grill
on its back, loosen all 4 bolts on the
bottom side of the Grill, but do not
relnove.(See Fig. 5)
.
.
Using 2 self, tapping hex head screws,
attach the magnetic door catch in the 2 holes
in the bottom of'the grill. (See Fig. 6)
ttave someone help you pick up the grill
and set it on the top of the cart, with the front
of" the grill above the door opening. Make
sure the 4 bolt heads f;all through the large
opening of" the key hole slots in the top of" the
cart. Slide the grill head backward, so the
bolts are resting in the small opening of the
key hole slots. Tighten the bolts securely.
Be sure not to over tighten and strip the
bolts. Next insert 4 hex head screws into grill
bottom through cart. (See Fig. 7)
Note: This is avery heavy step that requires
two individuals to complete.
Installing the Cart Door
.While holding the door line up the bottom
hole on the door with the bolt sticking up
through base of cart. Next place a nylon
bushing onto the top pin, then depress the pin
and insert into the hole in the bottom of'the
grill. (See Fig. 8)
Screw hole lbr
magnetic catch
Fig. 5
Fig. 6
Fig. 7
Fig. 8

Installing the Cart Door Handles
.Using a 5/32" allen wrench insert 1 screw
through the inside of the door front into
a bar handle end and tighten securely.
(See Fig. 9)
.Insert Bar tlandle into the End Cap
attached to the door and then into the
other End Cap and tighten End Cap with
allen wrench and screw. (See Fig. 10)
3. Complete Door. (See. Fig. 11)
Screw Holes
Backside of door:
2 screw locations
Fig. 9
Installing the Drip Tray
.The drip pan is installed inside of the cart
under the grill head.
.Slide the drip pan onto the two ledges located
on the bottom of the grill, by inserting it from
the front of the cart. (See Fig. 12)
Fig. 10
Grill
Fig. 12
Fig. 11

Side Shelf Attachment
.Attach the shelf to the left side of grill by
inserting the shelf hooks into the slots on the
side of the grill and pushing down on the shelf
assembly until level with grill. (See Fig. 13)
.Lock the shelf in place by inserting (2) self
taping screws into shelf: (See Fig. 14)
Shelf Hooks
Fig. 13
Interior parts installation
.Check to make sure the bottom Flavor
Grids are correctly installed in the cutouts and
around the ignitors, as they may have shifted
during shipment. (See Fig. 15)
.Insert the second row of Flavor Grids into
cutouts with triangle ridges facing up.
(See Fig. 16)
.Install cooking grates on the ledges provided
on the grill to create your cooking surface.
(placing the one with a thumb hole in the
middle) (See. Fig. 17)
.Place warming shelf on support brackets by
setting it fiat across brackets allowing the two
holes to line up with the stops on each
bracket. (See Fig. 18)
Fig. 14
Fig. 15
Fig. 16
Fig. 18 Fig. 17

.
.
Note:
.
.
Attach the Side Burner to the grill by
inserting the shelf hooks into the slots on the
side of the grill and pushing down on the shelf
assembly until level with the grill
(See Fig. 19)
Lock the Side Burner in place by re-inserting
(2) hex head screws in the front & rear edge
of side burner. (See Fig. 20)
A power screwdriver extension is needed to
insert screw.
Attach the Flex Line coming from the side of
the grill to the fitting on the bottom of the
Side Burner. (See Fig. 21)
Attach the ignitor wire coming out from the
side of the grill to the side burner ignitor
point. (See Fig. 22)
SCREW HOLE
Attach to fitting
Fig. 19
Fig. 20
Fig. 21
ignitor
",,,'ire
hookup
Fig. 22