SERVICE DATA SHEET
Electric Ranges with ES 100/105 Electronic Oven Control
Electronic
OvenControl
(E.O.C. Rear View)
IMPORTANT
DO NOT REMOVE THIS BAG
OR DESTROY THE CONTENTS
WIRINGDIAGRAMSANDSERVICE
INFORMATION ENCLOSED
REPLACE CONTENTS IN BAG
RTD SCALE
Temperature (°F) Resistance (ohms)
32 ± 1.9 1000 ± 4.0
75 ± 2.5 1091 ± 5.3
250 ± 4.4 1453 ± 8.9
350 ± 5.4 1654 ± 10.8
450 ± 6.9 1852 ± 13.5
550 ± 8.2 2047 ± 15.8
650 ± 9.6 2237 ± 18.5
900 ± 13.6 2697 ± 24.4
Resistance Temperature Detector
ElectronicOvenControl(E.O.C.) Connections(J1)
p/n 316904421 (0912)
NOTICE - This service data sheet is intended for use by
persons having electrical and mechanical training and a level of
knowledge of these subjects generally considered acceptable
in the appliance repair trade. The manufacturer cannot be
responsible, nor assume any liability for injury or damage of any
kind arising from the use of this data sheet.
SAFESERVICINGPRACTICES
To avoid the possibility of personal injury and/or property damage, it is
important that safe servicing practices be observed. The following are
examples, but without limitation, of such practices.
1. Before servicing or moving an appliance remove power cord from
electrical outlet, trip circuit breaker to OFF, or remove fuse.
2. Never interfere with the proper installation of any safety device.
3. GROUNDING: The standard color coding for safety ground wires is
GREEN or GREEN WITH YELLOW STRIPES. Ground leads are
not to be used as current carrying conductors. It is extremely
important that the service technician reestablish all safety
grounds prior to completion of service. Failure to do so will
create a potential safety hazard.
4. Prior to returning the product to service, ensure that:
• All electric connections are correct and secure.
• All electrical leads are properly dressed and secured away from
sharp edges, high-temperature components, and moving parts.
• All uninsulated electrical terminals, connectors, heaters, etc. are
adequately spaced away from all metal parts and panels.
• All safety grounds (both internal and external) are correctly and
securely reassembled.
Oven Calibration
Set the electronic oven control for normal baking at 350°F. Obtain an
average oven temperature after a minimum of 5 cycles. Press CANCEL
or CLEAR OFF to end bake mode.
Resistance Temperature Detector Scale
Electronic Oven Control (E.O.C.) Fault Code Descriptions (models that display F1 or F3)
Note: Only two fault codesare displayedby this control- F1 orF3. Generally, F1 displayimplies the electronic oven control itself has detected an internal
malfunction. F3 implies the control has detected a sensor probe failure. In either case, an alarm will accompany a displayed F1 or F3.
1. Shorted keypad.
2. Control's internal checksum may have become corrupted.
3. Control has sensed a potential runaway oven condition. Control
may have shorted relay, RTD sensor probe may have gone bad.
1. Open RTD sensor probe.Note: The EOC will initially display an F1
forthiscondition.TheEOCthinksarunawayoven conditionexists.
2. ShortedRTDsensorprobe. Note: The F3forshortedprobe should
only occur when the oven is active or when an attempt is made to
enter a mode.
Likely Failure Condition/Cause Suggested Corrective Action
Fault Code
1. Disconnectpower,wait 30secondsand reapplypower.If faultreturns
upon power-up, replace EOC.
2. Check RTD sensor probe and replace if necessary. If oven is
overheating, disconnect power. If oven continues to overheat when
thepower isreapplied, replaceEOC.Severeoverheatingmayrequire
the entire oven to be replaced, should damage be extensive.
3. Replace EOC.
1. Check resistance at room temperature and compare to RTD sensor
resistancechart.Ifresistancedoesnot match the chart, replace RTD
sensor probe.
2. Checkresistanceatroomtemperature,iflessthan 500ohms,replace
RTD sensor probe.
F1
F3
Runaway temperature.
Shorted keypad.
Bad micro identification.
Bad EEPROM identification/checksum error.
Open probe connection.
Shorted probe connection.
Likely Failure Condition/Cause Suggested Corrective Action
Fault Code
1. (F10 only) Check RTD Sensor Probe & replace if necessary. If oven is overheating,
disconnect power. If oven continues to overheat when the power is reapplied, replace EOC.
Severe overheating may require the entire oven to be replaced should damage be extensive.
2. (F11 & 13) Disconnect power, wait 30 seconds and reapply power.
3. (F11 & 13) If fault returns upon power-up, replace EOC.
1. (F30 or F31) Check resistance at room temperature & compare to RTD Sensor resistance
chart. If resistance does not match the RTD chart replace RTD Sensor Probe. Check Sensor
wiring harness between EOC & Sensor Probe connector.
2.(F30orF31)Checkresistanceatroomtemperature,iflessthan500ohms,replaceRTDSensor
Probe. Check for shorted Sensor Probe harness between EOC & Probe connector.
F10
F11
F13
F30
F31
Electronic Oven Control (E.O.C.) Fault Code Descriptions (models that display F10, F11, F13, F30 or F31)
CircuitAnalysisMatrix
Important notes:
•The oven temperature adjustment may be made if your oven control has been
set for °C (Celsius) temperature display mode. In this case each press of the
UP ARROW or DOWN ARROW key pad will adjust in 1°C increments upward
(maximum +18°C) or downward (maximum -18°C), depending on which
arrow keypad is pressed.
•If at any time during the process of adjusting the oven temperature feature
you decide not to make the change, press the CANCEL or CLEAR OFF key
pad once before the acceptance beep.
•The oven temperature adjustment feature can not be modified if BAKE or
BROIL is active.
Oven Temperature Adjustment (some models)
1. Press & hold the BAKE key pad and release after the display shows the
factory temperature setting of 00. If the oven temperature has been
previously adjusted from the factory setting, the latest adjusted value will
appear in the display instead.
2. You may increase the oven temperature in 5°F increments with each press
of the UP ARROW key pad. You may also adjust the oven temperature
downward in 5°F increments with each press of the DOWN ARROW
keypad (total adjustment range is +35°F to -35° F).
3. To accept the change, wait until the oven control provides the acceptance
beep (See important notes).
4. The oven temperature adjustment has been made by the oven control and
the display will return to the time of day.
