ICE MAKER INFORMATION
Test Cycling
Remove cover by inserting screwdriver in notch at
bottom and prying cover from housing. Use screwdriver
to rotate motor gear counterclockwise until holding
switch circuit is completed. All components of ice maker
should function to complete the cycle.
ATADECNAMROFREP GNITTESLORTNOCTNIOP-DIMTASGNINEPOROODONDNADAOLON
roticapaCtratS/nuRhtiWAepyTtneibmA)C°81(F°56 tneibmA)C°23(F°09
emiTgnitarepO%53ot52%55ot54
erutarepmeTrezeerFF°8ot°2
C°31-ot°71-
F°5ot°0
C°51-ot°81-
erutarepmeTerutaregirfeRF°04ot°53
C°4ot°2
F°04ot°53
C°4ot°2
(erusserPediSwoL
)ni-tuc
gisp61ot8
aPk011ot55
gisp61ot8
aPk011ot55
(erusserPediSwoL
)tuo-tuc
gisp4ot1
aPk82ot7
gisp4ot1
aPk82ot7
(erusserPediShgiH
)elcycfo3/1tsaL
gisp021ot011
aPk728ot857
gisp571ot051
aPk7021ot4301
)elcycfo3/1tsaL(egattaW581ot041581ot041
)gninnuR(spmA6.1ot1.16.1ot1.1
egatloVesaBCAV511CAV511
SNOITACIFICEPSTSORFED
eziStenibaC tatsomrehTretaeH
ni-tuCtuo-tuCsttaWsmhO
"81F°52
C°4-
F°74
C°8
57353
emiTnuRrosserpmoCfosruoH01yrevEsetuniM03tsorfeD
ROTOMNAFRESNEDNOC
sttaWMPRspmA
3.2tfahSetisoppOWC0031gninnuR51.
SNOITACIFICEPSREKAMECI
lacirtcelEstloV511ztreH06
tatsomrehT)C°9(F°84tasnepO)C°9-(F°51tasesolC
egattaWretaeH561
Water Fill Volume
The water fill adjustment screw will change the fill time.
One full turn is equal to 20cc (.68 oz.). The correct fill
is 90 to 120cc (3.0 to 4.0 oz.). The correct fill time is
6.9 sec. (+.6, -.4 sec) When a water valve is replaced,
the fill volume must be checked.
SNOITCENNOCGULPROTCENNOCREKAMECI
rebmuNeriWroloCeriW:otstcennoC
1wolleY/neerGdnuorG
2wolleYevlaVretaW
3kcalBeniL
4eulB.tLlartueN
SERVICE DATA SHEET - 240379003
R134a
STANDARD - AUTOMATIC DEFROST
TOP FREEZER MODELS
CAUTION: System parts must be removed from cabinet before
brazing.All electrical parts and wiring must be shielded from torch
flame. Do not allow torch to contact insulation; it will char at 200°F
andflashignite(burn)at500°F.Excessiveheatwilldistorttheplastic
liner.
IMPORTANT SAFETY NOTICE
The information provided herein is designed to assist qualified repair
personnel only. Untrained persons should not attempt to make repairs due
to the possibility of electrical shock. Disconnect power cord before servicing.
IMPORTANT
If any green grounding wires are moved during servicing, they must be
returned to their original position and properly secured.
