Frigidaire PRMC2285AF User manual

Frigidaire.com USA 1-800-374-4432 Frigidaire.ca Canada 1-800-265-8352
use
&
care
REFRIGERATOR
Introduction.......................................................2
Important Safety Information ....................3
Features..............................................................6
Installation .........................................................8
Door Removal.................................................10
Door Handle Installation............................. 14
Water Supply Connection.......................... 16
Controls and Settings.................................. 18
Automatic Ice and Water Dispenser..... 27
Storage Features........................................... 31
Storing Food and Saving Energy........... 35
Normal Operating Sounds........................36
Filter Replacement ...................................... 37
Care and Cleaning ....................................... 39
Troubleshooting............................................. 41
Limited Warranty .........................................46
A16492304 (May 2021)

INTRODUCTION
Doors
Handles are secure and tight
Door seals completely to cabinet on
all sides
Leveling
Refrigerator is level side-to-side and
slightly elevated in front to assist
with door and drawer closing (front
should be higher than back)
Cabinet is setting solid on all corners
Electrical Power
House power turned on
Refrigerator plugged in
Ice Maker
House water supply connected to
refrigerator
No water leaks present at all
connections - recheck in 24 hours
Ice maker is turned ON
Ice & water dispenser operates
correctly
Final Checks
Shipping material removed
Fresh food and freezer
temperatures set
Registration card sent in
Installation Checklist

Welcome to our family
Thank you for bringing Frigidaire into
your home! We see your purchase as the
beginning of a long relationship together.
This manual is your resource for the use
and care of your product. Please read
it before using your appliance. Keep it
handy for quick reference. If something
doesn’t seem right, the troubleshooting
section will help you with common issues.
FAQs, helpful tips and videos, cleaning
products, and kitchen and home accessories
are available at Frigidaire.com.
We are here for you! Visit our website,
chat with an agent, or call us if you need
help. We may be able to help you avoid
a service visit. If you do need service, we
can get that started for you.
Let’s make it ocial! Be sure to register
your product.
Keep your product info here so it’s easy
to find.
Model Number
Serial Number
Purchase Date
jfk;fkda;jfdajfk;fkda;jfdajfk;fkda;jfdajfk;fkda;jfda
jfk;fkda;jfdajfk;fkda;jfdajfk;fkda;jfdajfk;fkda;jfda
jfk;fkda;jfdajfk;fkda;jfdajfk;fkda;jfdajfk;fkda;jfda
jfk;fkda;jfdajfk;fkda;jfdajfk;fkda;jfdajfk;fkda;jfda
jfk;fkda;jfdajfk;fkda;jfdajfk;fkda;jfdajfk;fkda;jfda
Serial Number Location
2

WARNING
WARNING indicates a potentially
hazardous situation which, if not
avoided, could result in death or serious
injury.
IMPORTANT
IMPORTANT indicates installation, oper-
ation or maintenance information which
is important but not hazard-related.
DANGER
DANGER indicates an imminently
hazardous situation which, if not
avoided, will result in death or serious
injury.
CAUTION
CAUTION indicates a potentially
hazardous situation which, if not
avoided, may result in minor or
moderate injury.
Safety Definitions
This is the safety alert symbol. It is
used to alert of potential personal injury
hazards. Obey all safety messages that
follow this symbol to avoid possible injury
or death.
WARNING
CALIFORNIA RESIDENTS ONLY
Cancer and Reproductive Harm
www.P65Warnings.ca.gov
3
IMPORTANT SAFETY INFORMATION
WARNING
Please read all instructions before using
this refrigerator.
DANGER
DANGER Risk of fire or explosion.
Flammable refrigerant used. Do not use
mechanical devices to defrost refrigera-
tor. Do not puncture refrigerant tubing.
DANGER Risk of fire or explosion.
Flammable refrigerant used. To be
repaired only by trained service person-
nel. Use only manufacturer-authorized
service parts. Any repair equipment
used must be designed for flammable
refrigerants. Follow all manufacturer
repair instructions. Do not puncture
refrigerant tubing.
CAUTION
CAUTION Risk of fire or explosion.
Dispose of refrigerator properly
in accordance with the applicable
federal or local regulations. Flammable
refrigerant used.
CAUTION Risk of fire or explosion
due to puncture of refrigerant tubing.
Follow handling instructions carefully.
Flammable refrigerant used.

4IMPORTANT SAFETY INFORMATION
Safety Instructions
• DO NOT store or use gasoline, or
other flammable liquids in the vicinity
of this or any other appliance. Read
product labels for warnings regard-
ing flammability and other hazards.
• DO NOT operate the refrigerator in
the presence of explosive fumes.
• Avoid contact with any moving parts
of automatic ice maker.
• Remove all staples from the carton.
Staples can cause severe cuts, and
also destroy finishes if they come in
contact with other appliances
or furniture.
Child Safety
Destroy or recycle the carton, plastic
bags, and any exterior wrapping material
immediately after the refrigerator is
unpacked. Children should NEVER use
these items to play. Cartons covered with
rugs, bedspreads, plastic sheets or stretch
wrap may become airtight chambers, and
can quickly cause suocation.
Proper Disposal of Refrigerator
or Freezer
Risk of child entrapment
Child entrapment and suocation are not
problems of the past. Junked or aban-
doned refrigerators or freezers are still
dangerous – even if they will sit for “just
a few days”. When disposing of an old
refrigerator or freezer, please follow the in-
structions below to help prevent accidents.
Proper Disposal of Refrigerators/Freezers
We strongly encourage responsible appli-
ance recycling/disposal methods. Check
with the utility company or visit energy-
star.gov/recycle for more information on
recycling an old refrigerator.
IMPORTANT
CFC/HCFC Disposal
Some old refrigerators may have a cool-
ing system that used CFCs or HCFCs
(chlorofluorocarbons or hydrochloro-
fluorocarbons). CFCs and HCFCs are
believed to harm stratospheric ozone if
released to the atmosphere. Other re-
frigerants may also cause harm to the en-
vironment if released to the atmosphere.
If disposing of an old refrigerator, make
sure the refrigerant is removed for proper
disposal by a qualified technician. Inten-
tionally released refrigerant may subject
one to fines and imprisonment under
provisions of environmental legislation.
Before disposing of an old refrigerator/
freezer:
• Remove doors.
• Leave shelves in place so children
may not easily climb inside.
• Have refrigerant removed by a
qualified service technician.

5
IMPORTANT SAFETY INFORMATION
Grounding type wall receptacle
Power cord with
3-prong grounded plug
Do not, under
any circumstances,
cut, remove,
or bypass the
grounding prong.
Electrical information
• The refrigerator must be plugged
into its own dedicated 115 Volt, 60
Hz., 15 Amp, AC only electrical outlet.
The power cord of the appliance
is equipped with a three-prong
grounding plug for protection against
electrical shock hazards. It must
be plugged directly into a properly
grounded three prong receptacle.
The receptacle must be installed in
accordance with local codes and
ordinances. Consult a qualified
electrician. Avoid connecting
refrigerator to a Ground Fault
Interrupter (GFI) circuit. Do not use
an extension cord or adapter plug.
• If the power cord is damaged, it
should be replaced by an authorized
service technician to prevent any risk.
• Never unplug the refrigerator by
pulling on the power cord. Always
grip the plug firmly, and pull straight
out from the receptacle to prevent
damaging the power cord.
• Unplug the refrigerator before
cleaning and before replacing a light
bulb to avoid electrical shock.
• Performance may be aected if
the voltage varies by 10% or more.
Operating the refrigerator with
insucient power can damage the
compressor. Such damage is not
covered under the warranty.
• Do not plug the unit into an electrical
outlet controlled by a wall switch or
pull cord to prevent the refrigerator
from being turned o accidentally.

IMPORTANT
Accessories are available for refrigerator and can be purchased at Frigidaire.com or
by calling 1-800-374-4432.
Frigidaire Gallery
6FEATURES
*Features may vary according to model
A Adjustable Hinges
B Auto CrispSeal™ Drawers
C Flip Shelf*
D Flipper Mullion
E Fresh Food Ice Maker*
F Flipper Guide
G Air Filter
H Water Filter
I Dairy Compartment*
J Slide-Under Shelf*
K Cantilever Shelves
L Adjustable Door Bins
MSnackZone™ Storage Compartments
(Recessed below Crispers)
N Door Bin*
O Custom-Flex™ Temp Drawer
P Freezer Drawer
Q Freezer Basket
R Anti-tip Leg
A
B
C
D
E F GH
I
J
K
L
M
N
O
P
Q
R

IMPORTANT
Accessories are available for refrigerator and can be purchased at Frigidaire.com or
by calling 1-800-374-4432.
*Features may vary according to model
Frigidaire Professional
7
FEATURES
ASnackZone™ Storage Compartments
(Recessed below Crispers)
B Adjustable Hinges
C Auto CrispSeal™ Drawers
D Flip Shelf*
E Flipper Mullion
F Fresh Food Ice Maker*
G Flipper Guide
H Air Filter
I Water Filter
J Dairy Compartment*
K Slide-Under Shelf*
L Cantilever Shelves
M Adjustable Door Bins
N Door Bin*
O Custom-Flex™ Temp Drawer
P Ice Maker
Q Freezer Basket
R Anti-tip Leg
A
B
C
D
E
FGHI
J
K
M
N
O
P
Q
R
L

NOTE
If the refrigerator is placed with the
door hinge side against a wall, allow
additional space so the door can be
opened wider.
8INSTALLATION
CAUTION
Do Not install the refrigerator where
the temperature will drop below 55°F
(13°C) or rise above 110°F (43°C).
The compressor will not be able to
maintain proper temperatures inside
the refrigerator.
This Use & Care Manual provides general
installation and operating instructions for
this model. We recommend using a service
or kitchen contracting professional to
install the refrigerator. Use the refrigerator
only as instructed in this Use & Care
Manual. Before starting the refrigerator,
follow these important first steps.
Location
• Choose a place that is near a
grounded, non-GFCI, electrical outlet.
Do Not use an extension cord or an
adapter plug.
• If possible, place the refrigerator
out of direct sunlight and away from
the range, dishwasher, or other heat
sources.
• The refrigerator must be installed
on a floor that is level and strong
enough to support a fully loaded
refrigerator.
• Consider water supply availability for
models equipped with an automatic
ice maker.
Installation
Allow the following clearances for ease
of installation, proper air circulation, and
plumbing and electrical connections:
Sides & Top ⅜" (9.5 mm)
Back 1" (25.4 mm)
Door opening
The refrigerator should be positioned
to allow easy access to a counter
when removing food. For best use of
refrigerator drawers and freezer baskets,
the refrigerator should be in a position
where both can be fully opened.
Tools Necessary:
Phillips Head
or
Quadrex Head
Screwdriver
(OR) OR
8mm Socket
Wrench
Adjustable
Wrench
OR
⅜"
Fixed
Wrench
ANDAND
6mm
Allen Wrench

9
INSTALLATION
3. Ensure both doors are bind-free with
their seals touching the cabinet on all
four sides and that cabinet is stable.
Cabinet Leveling & Refrigerator
Door Alignment (if necessary)
Guidelines for final positioning of refrigerator:
• All four corners of the cabinet must
rest firmly on the floor.
• The front should be slightly elevated
to ensure that doors close and
seal properly.
• Doors should align with each other
and be level.
Most of these conditions can be met by raising
or lowering the adjustable anti-tip legs.
To level the cabinet using the anti-tip legs:
1. Slightly open freezer drawer.
2. Lower anti-tip legs until they are
both touching the floor. Use a pair of
pliers to adjust.
To raise unit: turn leg clockwise.
To lower unit: turn leg counterclockwise.
Raise
Flipper Mullion
Adjust Flipper Mullion for proper
connection with the mullion guide by
ensuring the flipper mullion is folded and
perpendicular to the fresh food door. If
the mullion guide is not in the correct
position, it could prevent the door from
closing completely.
WRONG
Anti-Tip
Legs
Door
Door
Door
Door
To make final door height adjustments:
1. Open Custom-Flex™Temp drawer to
make lower hinge visible.
2. Insert 6 mm AllenTM wrench into the
shaft of the lower hinge.
To lower door: turn adjustment
screw clockwise.
To raise door: turn adjustment
screw counterclockwise.

NOTE
Use care while pulling the water tube
from the door to be sure that tube does
not kink.
NOTE
Approximately four feet of water tube
will be pulled from the refrigerator door.
10 DOOR REMOVAL
Getting through narrow spaces
If refrigerator will not fit through an
entrance area, doors can be removed.
Check first by measuring the entrance.
To prepare for removing the doors:
1. Make sure the electrical power cord
is unplugged from the wall outlet.
2. Remove any food from the door
shelves and close the doors.
To remove the refrigerator doors:
1. Open doors to 90°.
2. Remove all five PhillipsTM screws
from top hinge cover and lift up.
Phillips Screws
Top
Hinge
Cover
5. Pull up on water line gently to
remove from door.
Waterline
3. Trace lightly around the door’s top
hinges with a pencil. This makes
reinstallation easier.
4. Disconnect electrical harness
running from door to hinge cover. 6. Remove three 8 mm bolts from both
top hinges. Lift doors up o lower
hinges and carefully set aside.
x2
CAUTION
Be sure doors are set aside in a secure
position where they cannot fall and cause
personal injury, or damage to the doors or
handles.

IMPORTANT
Make sure water line tubing goes
through hole at top of dispenser pocket.
There is also a metal wrap on the tubing
to prevent damage from the hinge rub-
bing against it. This needs to be fixed
back around the tube in the proper loca-
tion upon reinstallation (just as long as
the tube is protected from the hinge).
NOTE
When reinserting the water tube and
replacing the top hinge cover, use care
to be sure the tube does not kink.
NOTE
Optional Door Opening Angle Feature
Parts are identified:
LH—Left Hand, to apply on Left Door
RH—Right Hand, to apply to Right Door
11
DOOR REMOVAL
Lower Hinge Removal
Once both doors are in place, ensure they
are aligned with each other and level (Ref-
erence the Installation section for more
details), and replace the top hinge cover.
8. To reinstall doors, reverse procedure.
7. To gain access to lower hinge, drawer
will need to be extended. Unscrew the
three lower hinge screws and slide the
hinge inwards.
Prevent doors from touching walls
If your refrigerator doors are touching
objects such as a wall or a countertop
located close to the side of the appliance,
the doorstop can be replaced with the
provided Optional Door Opening Angle
Feature located in your crisper drawer.
This is to reduce the maximum door
opening angle for both doors or for one
specific door.
Door Stop Default
Maximum Opening Angle: 123°
Optional Door Opening Angle Feature

12 DOOR REMOVAL
Once the doors are removed from the unit,
using the previous steps in “To remove
the refrigerator doors” in the DOOR
REMOVAL section, perform the following
steps to remove and replace the door stop:
1. Turn the refrigerator door upside
down to access the door stop
located in the hinge area of the door.
Door Stopper Removal
2. Remove the 2 screws from the
door stop.
3. Replace the door stop with Optional
Door Opening Angle Feature. Insert
the 2 screws and retighten to secure
the hinge assembly.
4. Repeat the process for the opposite
refrigerator door.
5. Reinstall the doors to the cabinet.
To remove the Custom-FlexTM
Temp Drawer
1. Fully open
drawer.
2. Remove
basket from
drawer.
3. Unsnap the
4 cable ties
by pressing clip sides together and
pushing through opening.
4. Remove screw and retaining clip and
disconnect the harness
5. Remove drawer by pressing on the
liner clips and slide rail past clips on
both sides to fully remove drawer
from cabinet.
Press the two
tabs on both
sides to release
the sliders
Cable
Tie
Cable
Clip
NOTE: Do Not Remove or Cut
Cable Ties From Wire Harness
(4) Cable
Ties
Retaining
Clip
Retaining Clip
To Cabinet
Harness
Screw
Optional Door Opening Angle Feature
Maximum Opening Angle: 105°

NOTE
For additional instructions, see
STORAGE FEATURES section.
13
1. Open drawer and fully extend.
2. Remove the freezer drawer.
3. Remove the freezer basket.
4. Inside the cabinet, press the two
tabs on both sides to release the
sliders.
5. Remove the drawer with brackets
and sliders.
Removing Freezer Drawer
DOOR REMOVAL
Freezer
Drawer
Freezer
Basket
Press the two tabs
on both sides to
release the sliders
Reinstalling Freezer Drawer
1. Place drawer with brackets and
sliders inside the cabinet and click
into place.
2. Replace the basket.
CAUTION
Drawer is heavy. Use caution when lifting.
Reinstalling the Custom-FlexTM
Temp Drawer
1. Place drawer with brackets and
sliders inside compartment and click
sliders into place on each side.
2. Reconnect cabinet harness.
3. Replace retaining clip and secure with screw.
Retaining Clip
Reconnect
Cabinet Harness Screw
12
4. Reattach electrical harness by
positioning the cable clips over the black
markings on the harness and push the
4 cable clips through openings in rail to
secure harness in place.
Black
Marking
Position
cable clips
over the black
markings before
attaching.
5. Slide
basket into
place.
6. Close
drawer.
Click
Into Place

14
NOTE
All set screws should be tightened so the screw is below the surface of the handle.
The handles should be drawn tight to doors/drawer with no gaps. Opening the op-
posite door while tightening the Allen screw makes installation easier.
The door handle may loosen over time or if it was installed improperly. If this hap-
pens, tighten the set screws on the handles.
Door Handle Mounting
Instructions for
Frigidaire Gallery
1. Remove handles from
carton and any other
protective packaging.
2. Position fresh food handle
end caps over upper
and lower pre-installed
shoulder bolts (A) that
are fastened into door,
ensuring the holes for
the set screws are facing
towards the opposite door.
3. While holding handle
firmly against door, fasten
upper and lower Allen set
screws (B) with supplied
Allen wrench.
4. Repeat steps 2 and 3 to
install opposite handle.
Ensure the holes for the
set screws are facing
towards the first door.
5. Position freezer/Custom-Flex
TM
Temp Drawer handle end caps
over left and right pre-installed
shoulder bolts (A) that are
fastened to the door, ensuring
the holes for the set screws are
facing down.
6. While holding handle
firmly against door,
loosely tighten right
Allen set screw (B) with
supplied Allen wrench
until there is no gap
between handle and door.
7. Still holding the handle firmly
to the door, firmly tighten
left Allen set screw (B) with
supplied Allen wrench.
8. Return to the right Allen
set screw (B) and firmly
tighten with supplied
Allen wrench.
Mounting Freezer
Custom-FlexTM Temp Drawer Handle
Mounting Refrigerator Handles
DOOR HANDLE INSTALLATION
NOTE
When tightening the Allen set screws, it is impera-
tive that force be applied to the longer arm of the
Allen wrench supplied in the handle packaging.
CAUTION
Wear gloves and safety goggles. Use extreme CAUTION when installing these handles.

15
DOOR HANDLE INSTALLATION
Door Handle Mounting Instructions for Frigidaire Professional®
Mounting Refrigerator Handles
NOTE
When tightening the Allen set screws, it is imperative that force be applied to the
longer arm of the Allen wrench supplied in the handle packaging.
NOTE
All set screws should be tightened so the screw is below the surface of the handle.
The handles should be drawn tight to doors with no gaps. Opening the opposite
door while tightening the Allen screw makes installation easier.
The door handle may loosen over time or if it was installed improperly. If this hap-
pens, tighten the set screws on the handles.
1. Remove handles from carton
and any other protective
packaging.
2. Position fresh food handle end
over upper and lower pre-
installed shoulder bolts (A)
that are fastened into door,
ensuring the holes for the set
screws are facing towards the
opposite door.
3. While holding handle firmly
against door, fasten further
most upper and further most
lower Allen set screws (B) with
supplied Allen wrench.
4. Repeat steps 2 and 3 to install
opposite handle. Ensure the
holes for the set screws are
facing towards the first door.
5. Firmly tighten the inside Allen
set screws.
CAUTION
Wear gloves and safety goggles. Use extreme CAUTION when installing these handles.

16 WATER SUPPLY CONNECTION
WARNING
To avoid electric shock, which can
cause death or severe personal injury,
disconnect the refrigerator from
electrical power before connecting a
water supply line to the refrigerator.
NOTE
Check with local building authority for
recommendations on water lines and
associated materials prior to installing
refrigerator. Depending on local/state
building codes, Frigidaire recommends
for homes with existing valves its Smart
Choice®water line kit 5304437642 with
a 6ft. (1.8 meters) braided Stainless
Steel Water Line. Please refer to
Frigidaire.com for more information.
CAUTION
To Avoid Property Damage:
• Copper or Stainless Steel braided
tubing is recommended for the
water supply line. Water supply
tubing made of ¼inch plastic is not
recommended to be used. Plastic
tubing greatly increases the potential
for water leaks, and the manufacturer
will not be responsible for any
damage if plastic tubing is used for
the supply line.
• DO NOT install water supply tubing
in areas where temperatures fall
below freezing.
• Chemicals from a malfunctioning
water softener can damage the ice
maker. If a water softening system
is present, ensure the softener is
maintained and working properly.
IMPORTANT
Ensure that the water supply line con-
nections comply with all local plumbing
codes.
To install the water supply line, the
following are needed:
• Basic Tools: adjustable wrench,
flat-blade screwdriver, and PhillipsTM
screwdriver
• Access to a household cold water
line with water pressure between 30
and 100psi.
• A water supply line made of ¼inch
(6.4mm) OD, copper or braided
stainless steel tubing. To determine
the length of tubing needed, measure
the distance from the ice maker inlet
valve at the back of the refrigerator
to the cold water pipe. Then add
approximately 6ft. (1.8m.), so the
refrigerator can be moved out
for cleaning.
• A shuto valve to connect the water
supply line to the household water
system. DO NOT use a self-piercing
type shuto valve.
• Do not reuse compression fitting or
use thread seal tape.
• A compression nut and ferrule
(sleeve) for connecting a copper
water supply line to the ice maker
inlet valve.
NOTE
Expect the first ice harvest within first
24hours of unit operation. To prevent any is-
sues concerning ice production, please ensure
that all water lines are primed. See “Priming
the water supply system” in the AUTOMATIC
ICE AND WATER DISPENSER section.
IMPORTANT
The refrigerator’s water supply system
includes several tubing lines, a water filter,
and a water valve. To ensure that the
water dispenser works properly, this sys-
tem must be completely filled with water
when the refrigerator is first connected to
the household water supply line.

17
WATER SUPPLY CONNECTION
To Connect Water Tube to
Household Water Supply
1. Disconnect
refrigerator
from electrical
power source.
2. Place end of
water supply
line into sink
or bucket.
Turn ON water
supply and
flush supply
line until water
is clear. Turn
OFF water
supply at
shuto valve.
Place 7/16" wrench
here. Do not turn.
Place 1/2" wrench
here. Turn
clockwise.
6. Replace the connected tubes into
the clips and lock clips back in
place to keep the tubing in the right
position.
7. Turn ON water supply at shuto
valve and tighten any connections
that leak.
8. Reconnect refrigerator to electrical
power source.
9. Ensure ice maker is turned ON.
10. Purge air from Ice and Water Dispenser
System by operating the water
dispenser for 3-4 minutes. This will
require dispensing several glasses of
water.
3. Open the locking
clips and grab
water line
coming from
the refrigerator.
Remove plastic
cap from water
inlet fitting and
discard cap.
4. If using
(recommended) stainless steel
braided tubing - the nut and ferrule
are already assembled on the
tubing. Slide compression nut onto
water inlet fitting and finger tighten.
5. Using ½” and ⁷⁄₁₆” wrenches (one to
hold the household water line nut
and the other to hold the water inlet
fitting nut), tighten a half turn with
wrench. DO NOT over tighten.
Water
inlet
fitting
Plastic
tubing
to
water
valve
6 ft. (1.8 Meters) Stainless
Steel water line from
household water supply line
Connection to Household Water Supply
with 1/4" compression
fitting
Plastic
Cap
Remove
plastic cap
from water
inlet fitting
Water Inlet
Brass
Fitting
¼ inch
plastic tube
to water
valve
To
household
water
supply
To
unit
water valve

18
Awake Mode Display
Awake Mode
To change from sleep mode (on) to awake mode (o), simultaneously press and
hold Crush and for 5 seconds. Display will show the current temperature/ice maker
status. Tone will confirm.
Sleep Mode Display
Sleep Mode
As a default, the display will go to sleep after a short time. If any icon is pressed, the
display will be awakened. After a short time, it will go back to sleep. When in sleep
mode, wake up the display to confirm ice maker is On/O. Sleep mode can be turned
o to have the display on full time (awake mode). When sleep mode is O, the display
will always be illuminated. To turn sleep mode On/O, simultaneously press and hold
Crush and for 5 seconds. Tone will confirm.
CONTROLS AND SETTINGS
Frigidaire Gallery Display (options may vary by model)

19
CONTROLS AND SETTINGS
Frigidaire Gallery Display (options may vary by model)
WARNING
When using Cold Drink Timer, remove
drinks from freezer compartment when
the alarm sounds. Carbonated drinks
may explode if left in the freezer for
too long.
1Freeze Boost (on/o)
Prior to grocery shopping, we
recommend you activate Freeze
Boost to freeze your food faster It will
remain active for up to 24 hours before
automatically deactivating or you
manually exit. Press Freeze Boost to
turn the function o. This will reset the
freezer to the previous temperature.
2Cold Drink Timer
Quickly chills a drink inside the freez-
er compartment. To enable, touch
Cold Drink Timer. A time value (in
minutes) will appear on the freezer
temp display and can be changed
using the +/-buttons. A tone will
sound when you input the time. The
range is from 20-45 minutes in 5
minute intervals. Drinks will freeze if
the temperature setting is too low or
the timer setting is too long.
3Ice Maker
Press and hold for 3 seconds to
turn the ice maker on/o. When
the indicator is lit, the ice maker
is on. When the ice maker is OFF,
the Ice Maker O indicator is lit.
When the ice maker is OFF, it will
stop making ice. When the sleep
mode is enabled, wake the display
to confirm the ice maker is on/o
(see Sleep Mode section). While
o, ice dispensing can continue as
long as there is ice in the bucket.
When the ice maker is o and ice is
dispensing, the indicator above Ice
Maker and Ice Maker O will both
blink.
4The lock button can be used to lock
the display preventing it from being
used in certain situations. Press and
hold for 3 seconds to enable/dis-
able. While locked, no changes can
be made to settings on the display.
Dispensing ice and water will be
disabled. The indicator will flash and
an audible warning will sound.
5Power Outage
In the event of a power failure,
Power Outage will illuminate once
power has been restored and
a tone will sound. The alert will
only illuminate if the refrigerator
or freezer reached unsafe
temperatures during the outage.
Press any button to silence the tone.
10
1
2
3
4
5
6
7
98
11 12
13
14
15
16
17

20 CONTROLS AND SETTINGS
Frigidaire Gallery Additional Features (Continued)
6Adjusting Temp
Illuminates when temperatures are
changed on the display and will
remain illuminated until the desired
temperatures are reached inside
the refrigerator and freezer. Press
either the +or —to adjust to desired
temperature setting.
Freezer temp
Control temperatures range from
-6°F / -21°C to +6°F / -15°C.
Refrigerator temp
Control temperatures range from
+34°F / +1°C to +44°F / +7°C. This
unit is designed to operate at 37°F
Refrigerator/0°F Freezer. The unit
should stabilize temperatures within
24 hours of installation.
7Door Open
Illuminates whenever the doors
are open. If a door is left open for
5 minutes or more, an alarm will
sound and the display will illuminate
until the doors are shut. Pressing
any button will mute the alarm
temporarily. Check to make sure no
food is blocking the doorway.
8Replace Water Filter
Display illuminates every 6 months
or when filter needs replacing.
Replace the filter and then press
and hold Reset Water Filter for 3
seconds to deactivate the warning
on display. See Replacing the
Filter for more information.
9Replace Air Filter
Display illuminates every 6 months
or when filter needs replacing.
Replace the filter and then press
and hold Reset Air Filter for 3
seconds to deactivate warning on
display. See Replacing the Filter
for more information.
10 Water
Press Water to dispense water. An
indicator light will illuminate above
the active feature.
11 Cube
Press Cube to dispense cubed ice.
An indicator light will illuminate
above the active feature.
12 Crush
Press Crush to dispense crushed ice.
An indicator light will be illuminated
above the active feature.
13 °F/°C
To toggle between Fahrenheit (°F)
and Celsius (°C), simultaneously
press and hold +and —for 5
seconds on the refrigerator side of
display.
14 Chill Boost
Chill Boost is a faster rate for
chilling food in the refrigerator
compartment. Use this feature
when loading several items into
the refrigerator at one time. It
deactivates after 6 hours.
15 Reset Air Filter
After replacing the filter, press and
hold for 3 seconds to reset.
16 Reset Water Filter
After replacing the filter, press and
hold for 3 seconds to reset.
17 Toggles dispenser light On and O.