FRISKA Stockholm Micro Desk User manual

Stockholm Micro Desk Assembly

SWITCH
H
I
G
D
D
A
AC
B
B
E
2
Basic control switch
Optional - Packed
with desktop
Memory control switch
'F'
( x 5)

3
8x 8x 16x 16x 8x 4x
FIXING
COMPONENT LI T
L M N P* R S
*P - These screws must only be used for frame only configuration
or when using a desktop without metal screw inserts.
A- Desk Legs
B- Under-desk Support Arm
C- Cross Beam
D- Feet
E- Power supply lead
F- Control switch (Basic or Memory)
G- Power supply lead
H- Self Adhesive Cable Clips
I- Cable Port Cover (Optional)
REQUIRED TOOLS
HEX
4mm
HEX
5mm
(supplied) (Not supplied)

4
1.
A
A
2.
C
F
CAUTION
Components are heavy – take care when handling
!
‘L’ x4
Insert screws but
do not tighten.
Gap needed for
frame and brackets
in steps 4and 5.
Feed leg motor cables
through centre hole

5
3.
4.
‘L’ x4
Fully
tighten
screws.
Do not tighten: Keep loose for step 5.

6
5.
B
B
Fully
tighten
screws.
x4
It may be necessary to use asoft headed mallet to fit
tight fitting support arm onto the leg / frame.

7
6.
‘M’x8
D
D
Fully
tighten
screws.

8
7.
8.
‘S’ x4
NOTE Check desktop for any delivery
damage before commencing this stage.
!
!NOTE Carefully unpack the desktop leaving it face
down on the packaging supplied so as to protect the
work surface.
Hand tighten
fully into foot.
Basic control switch
Memory control switch

9
9.
CAUTION
Frame is heavy – take care when positioning it.
!
‘SWITCH’
NOTE Insert switch into
aperture by applying firm, even
pressure. Ensure correct
orientation of switch within the
aperture. Basic control has ‘UP’
stamped on the rear, position
this furthest from the front
edge.
Carefully lower the frame onto
the underside of the desktop.

10
10.
!NOTE Use P x16 only if using desktop
without metal screw inserts
‘P’x16 ‘N’x16
‘N’x14 when
Cable Tray Used
Fully
tighten
screws.
Fully
tighten
screws.
Omit screws if
fitting cable tray

11
11.
‘R’x8
!NOTE Double check all screws are now tight
!NOTE Fit the plastic caps to exposed frame screw heads. Press hard to
locate the caps onto the screws and tap home securely using a mallet
The caps are designed to mould onto the screws through force.

12
12. NOTE All leads MUST be plugged into the control box
before connecting power lead and switching the power
on. Failure to comply could result in damage to the unit.
!
G
‘N’x2
E
G
G
A
A
SWITCH
Fully
tighten
screws.

13
13.
NOTE For ease of assembly, fit
optional cable tray before turning
desk over to upright position
!
CAUTION - Desk is heavy -
2 person operation
!
‘H’x5
Use cable clips 'H'
to keep cables tidy.
Desk is now ready to use.
Turn upright and perform
reset procedure - see p. 18.

OPTIONAL CABLE TRAY
T6
x4 x4
T2
T3 T3
T4 T5
T1
T7
NOTE - Pull both ends of
the tray to expand, suitable
for 100-180cm desktops
14
NOTE! When mounting the cable tray on
a 600mm deep top and using a monitor
arm assembly, the cable tray will have to
be mounted inside of the desktop support
arms and fixed directly to the desktop with
woodscrews to allow clearance of the
monitor arm fixing bracket.

x2 x2
‘T7’ x4
15
14.
T2 T2
T1
Fully tighten
screws.
Omit screws to
fit Cable Tray.

‘T6’x4
T4
T5
T3
16
Fully
tighten
screws.

17
15.
16.
NOTE - Desk can be plugged
into the optional power lead
and hidden in cable tray.
'I'

PRESS!
RE ET PROCEDURE
IMPORTANT!
A reset procedure MUST be carried out immediately following
assembly of the desk.
• Lower the desk to its lowest position by pressing the down
arrow on the hand control.
• Release the button.
• Press the button again and keep it pressed for 10 seconds
• The desk will make a jolting movement and click
• The reset is now carried out and the desk is ready to use
18

19
Select desired height using the 'UP/DOWN' button.
Press the 'SAVE' button followed by the memory number.
AVING A MEMORY PO ITION
1:
2:
3:

Friska Micro Desk Assembly Manual