Frontier airi Air 4920 User manual

INTERNET
BROADBAND
GATEWAY
Reset
WIFI
12V
ETHERNET
4
ADSL
3 2 1
On/Off
5 GHz
STB
WiFi-Client
WiFi-Client
WiFi-Client

INTERNET
2
1
BROADBAND
GATEWAY
Reset
WIFI
12V
ETHERNET
4
ADSL
3 2 1
On/Off
3
Designedby AirTies in Europe. Manufactured in China.
Wi-Fi Name: AirTies_Air4920_XXXX
Wi-Fi Password: abcdef1234
Designed by AirTies in Europe. Manufacturedin China.
Wi-Fi Name: AirTies_Air4920_XXXX
Wi-Fi Password: abcdef1234

BROADBAND
GATEWAY
STB
STB
5 GHz 5 GHz
5 GHz
WiFi-Client
WiFi-Client
NEW
EXISTING
EXISTING
WiFi-Client
STB
EXISTING
NEW
EXISTING
5 GHz
5 GHz
BROADBAND GATEWAY

LED
Indicato rs: Condition LED Color LED Behavio r Timing
State
Identifier Explanation Recommended Action(s)
Power OFF (OFF/Dark) A Power the device on if desired.
No other action required.
Power ON White B
No action required. If unit was just powered on, then please wait for at least 2 minutes for the unit to complete its boot process.
Device is not ready White C No action required. Please wait.
WLAN is active and the node has an active strong Mesh connection
on the Radio
Green Blinking 50ms OFF
5000ms ON D No action required.
Red EBring device closer to another device
on the MESH network.
WLAN is active and all MESH links on the Radio are weak Radio is inactive or Searching for radar activity (OFF/Dark) F No action required.
WPS is in progress Green G No action required. WPS is succesful Green H
This behavior is temporary and lasts for about 5 seconds, after which the LEDs
go to one of the following states: 1) MESH with strong signal (state D), and 2) MESH with poor signal (state E)
If LED is red (state E) then bring device closer to another device on the MESH network. If LED is green (state D), then no action is required.
Green 4000ms OFF
4000ms ON
Configure device (refer to Quick Installation Guide)
Unconfigured device WLAN active, Device configured, No MESH link on the Radio Green J
Device has factory setting and is not connected to the home network in any way (e.g., the device is not wired to the router-gateway) First AP (wired to router-gateway) No action required.
There is configured MESH connection on the radio, however connection is inactive (Can not connect) Red
-
Solid (No blinking)
Blinking
Solid (No blinking)
Blinking in sync
Solid (No blinking)
Blinking in sync
Solid (No blinking)
Blinking
1000msec OFF 1000msec ON K
AP is part of MESH, but unable to find any of its MESH partners.
Make sure other device(s) that are part of the MESH network are powered on and close enough to connect.
WPS is not successful Red L
This behavior is temporary and lasts for about 5 seconds, after which the LEDs go back to the state the device was in before the WPS attempt
On failure, repeat WPS attempt after
bringing device near another device that is already on the MESH network (i.e., in state D).
Power
2.4 GHz
5 GHz

Th�s product makes use of software developed by the open source commun�ty. Any such software �s l�censed under the spec�f�c l�cense terms appl�cable to that part�cular
software (l�ke GPL, LGPL etc). Deta�led �nformat�on on the appl�cable l�censes and l�cense terms can be found on the dev�ce's user �nterface.
By us�ng th�s product, you acknowledge that you have rev�ewed such l�cense terms and that you agree to be bound by them. Where such terms ent�tle you to the source code
of sa�d software, that source code w�ll be made ava�lable at cost upon request from A�rT�es.
To obta�n a copy of sa�d source code, please send your request �n wr�t�ng v�a ema�l to osrb@a�rt�es.com or v�a sna�l ma�l to:
A�rT�es W�reless Commun�cat�ons
Gulbahar Mah. Avn� D�ll�g�l Sok. No:5
Cel�k Is Merkez�, Mec�d�yeköy, 34394
ISTANBUL/Turkey
A�rT�es w�ll ma�l to you a CD w�th the requested source code at the cost of CD preparat�on and sh�pp�ng&handl�ng. For deta�ls please contact osrb@a�rt�es.com