Frossvt EM3105 User manual

Frossvt Espresso Coffee Machine
User Manual
Made in China
Item
EM3105
Voltage
120V
Frequency
60 Hz
Power
1350 W
Water tank
1.4 L
Pump Pressure
20 Bar


1
Before the First Use(Important)
1. Move the coffee maker from the package, and check the accessories
according to the list.
2. Clean all the detachable components.
3. Remove the red silicone from the water tank before using the coffee maker.
(Note: If the red silicone piece is not removed, the machine will be unable to pump
water)
4. Pour water into water tank and the water level should not exceed the "max"
mark. Put back the water tank and close the water cover.
5. Plug in and press the ON/OFF switch“ ”. At this time, all indicator lamps
are flashing. The machine starts to preheat, when the indicator lights stop
blinking and turns normal on, the preheat is completed, it takes about 1 minutes.
6. After the preheating is completed, turn the steam knob counterclockwise to
the maximum position, and the electromagnetic pump works until continuous hot
water comes out from the steam pipe and at least 30 seconds (this process
takes 1-2 minutes) to clean the steam pipe, then turn off the steam switch;
7. From position " " to position " " , rotate counterclockwise to install the
filter holder(No coffee powder added)into the funnel holder of the machine,
then touch the double-cup coffee switch“ ” to let the hot water out to wash
the coffee filter and the cup .

2
How to Make a Good Cup of Coffee
Grinding coffee bean and grinding quality largely determines the quality of
coffee, if the powder is too coarse, coffee extract inadequate, the taste is
light, and color is lighter, the cream also will be very thin, and color is white;
if the powder is too fine, coffee over extraction, it will be too dark, and no
cream. A good cup of coffee should use freshly ground coffee beans (use
burr coffee grinder), and use appropriate amount of coffee beans. Each
time when you making coffee with coffee powder, the freshness of the
beans is very important, long time storage will make coffee bean oil
decomposition.
1. Use the bean grinder to adjust the appropriate grinding thickness, and
then pour the fresh coffee beans into the grinding chamber for grinding.Use
the bean grinder to adjust the appropriate grinding thickness.
2. It is recommended to weigh each time you make coffee to ensure the
amount of coffee powder added (single cup: 9-9.5g; double cup: 16-16.5g),
and compact the coffee powder with a powder press;

3
3. Distance to the surface of pressed coffee powder should be about 3mm
away from the edge of the filter cup (important indicator). Too high or too low
will affect the extraction pressure and effect of coffee, please reduce or
increase the amount of coffee powder;
4. Make coffee liquid : single cup of coffee: 25-35g; double cup of
coffee :40-60g, this can be adjusted by the thickness of the ground coffee.

4
Accessories:
1.Water tank cover 2.Water tank 3.Steam control knob
4.Main body 5.Steam pipe and nozzle 6.Base
7.ON/OFF switch 8.Warm cup board 9.Single-cup coffee switch/
indicator lamp 10.Double-cup coffee switch/ indicator lamp 11.Steam
preheating switch/indicator light 12.pressure meter 13.Funnel holder
14.Buoy 15.Drip tray cover 16.Drip tray 17.Coffee spoon
18.Single-cup coffee filter 19.Double-cup coffee filter 20. Filter Holder
21.Coffee outlet
Warning: The machine must use a grinding Coffee powder and just make
coffee, coffee drink(ex: Cappuccino, Latte and so on), heating milk, and
other irregular use may cause danger.

5
Operation Manual
“ ”:ON/OFF switch, Press the switch,the machine is powered on , the
indicator lamp “ ”、“ ”and“ ” flashing on, the machine starts
to preheat. when the all indicator lamps stop blinking and turns normal on,
the preheating is completed, that the machine enters the making coffee or hot
water mode.Press the switch again during or after preheating, and the machine
is powered off. ( If the indicator lamp“ ”keeps flashing fast when the
machine is powered on, check the steam knob and rotate clockwise to put it
off.)
“ ”:Single cup of coffee switch, Touch it to start extracting coffee
after preheated , the indicator lamp " " breath flashes. Automatically
extract until the machine stops working or touch the button again to stop
working during the extraction process,the indicator lamp“ ”、“ ”
and“ ” become constant light. (The automatic extraction time
machine has been set and contains pre-brewed coffee time)

6
“ ”:Double cup of coffee switch,touch it to start extracting coffee
after preheated , the indicator lamp " " breath flashes。Automatically
extract until the machine stops working or touch the button again to stop
working during the extraction process,the indicator lamp “ ”、“ ”
and“ ” become constant light. (The automatic extraction time
machine has been set and contains pre-brewed coffee time)
" " : steam preheating switch, touch the switch, the indicator lamp
" " flashes ,begin to preheat the steam. After the preheated, the indicator
lamp " " become constant light and the machine enters the steam
making mode. (If you touch the steam preheating switch again during the whole
process, the machine switches back to the coffee extraction state from steam
preheating. If the indicator lamp“ ”、“ ”flashing , It indicates that the
coffee temperature is too high, you need to cool naturally or make hot water
manually. Coffee cannot be extracted until the indicator lamp “ ”、
“ ”and“ ” become constant light.)
The steam knob: The steam knob shown below is in the closed position.
There are two working states when the steam knob is turned on. When the
machine is in coffee mode, the steam pipe gives hot water. When the
machine is in steam mode, the steam tube gives steam .

7
Note: when the power is turned on, the steam preheating indicator keeps
flashing fast, it means that the steam knob is not closed, and you can
turn the steam knob to the closed position .

8
Make Espresso Coffee(Double-Cup Coffee
For Example)
1. Open the lid, take out water tank, and pour appropriate water into tank. Do
not exceed the MAX capacity;
2. Put back the water tank and close the lid;
3. Plug in and press the ON/OFF switch“ ”, all indicator lamps re flashing,
machine start preheating, preheating will be finished after 1min, coffee and
steam indicator lamp will always light on ;
4. Take out filter holder, pour appropriate coffee powder(16-16.5gram) into the
coffee filter with coffee spoon, then press the coffee powder tightly, clean the
extra coffee powder overflow the edge of holder, to avoid damage the seal ring
of group head.
Note: If too much coffee powder remaining in the edge of the filter, will
easily to cause poor sealing and water leakage.
5. Rotate the high-pressure funnel assembly counterclockwise from position

9
" " to position " " (must be tightened);
6. Put cup(s) under coffee outlet;
7. Touch the double-cup coffee switch“ ”, the machine starts pumping water,
and coffee flows out of the coffee nozzle;
8. The coffee machine automatically stops working (the light from Breathing light
on to a constant light), and the coffee is made at this time, then remove the
coffee cup;
Warning: Do not leave the coffee machine unattended during the coffee
making process, as it sometimes requires manual operation.
9. After the coffee is made, take out the high-pressure funnel assembly by
rotating it clockwise, clean the coffee grounds in the filter in time, and rinse it
with hot water. Touch the single-cup or double-cup coffee button, flush the
outlet with water, install the clean high-pressure funnel assembly on the
outlet, and wait for the next use.
10. When making a single cup of coffee, use a single-cup coffee filter, touch the
single-cup coffee switch when making, and the other steps are the same as
double-cup coffee making.
Warning: Do not touch the hot surfaces of the machine with hands to avoid
scald, especially brewing outlet, steam nozzle when use machine.

10
Make Cappuccino
1. Prepare espresso first with a large enough cup according to part “B;
2. Use whole, fresh cold milk out of the fridge(8℃-10℃), and pour 1/3 milk in
cup;
Note: Use a stainless steel cup, and cup diameter should not less than 70 ±
5mm, due to the volume of milk will increase after frothing.
3. Touch steam switch“ ”, it starts preheating, Single-cup and Double -cup
coffee indicator go out, steam indicator is flashing, then wait for steam
indicator lights on, now preheating finished.
4. Put an empty cup under the steam pipe, turn the "steam knob"
counterclockwise to the maximum position, release a little water in the steam
pipe, and turn the "steam knob" clockwise to turn off the steam after the
steam comes out.
5. Put a stainless steel cup under steam nozzle,Let the steam pipe nozzle float
below the surface of the milk;
6. Open steam knob, rotate it to the maximum position to frothing milk;
7. When desired milk foam reached, then turn off knob, steam is stopped,
remove cup and pour the frothed milk into prepared espresso, now
cappuccino is ready, you can add some sugar or Coco powder if you like it.
Note: After the steam stops spraying, please clean the steam pipe assembly
immediately and discharge the milk in the pipe to prevent the milk froth from
scaling on the pipe wall. During the operation, due to the high surface
temperature of the steam pipe, be sure not to be scalded.

11
Making Hot Water
1. Put a container under hot water outlet;
2. When all indicator lamp always keep on, Open steam knob, rotate it to the
maximum position, hot water will be come out from hot water pipe
immediately; In the process of making hot water, the single-cup coffee
indicator“ ” Breathing light on;
3. When the hot water reaches the required amount, turn the "steam knob"
clockwise to the off position, and the hot water stops flowing out.
Reminder: The hot water function can also be used to quickly cool down
the coffee machine.
Note: When using, be careful of the hot parts of the machine. Especially the
water outlet (funnel holder), hot water nozzle and steam pipe. When operating,
please do not put your hands on the above parts for any reason.
Heating Liquid (Steam Function)
1. Use a stainless steel cup, pour cold liquid to 1/2 cup;
Note: Cup diameter should not less than 70 ± 5mm. Because it is heated by
steam to avoid liquid overflows or spills when steam is released.
2. Touch steam button“ ”, it starts preheating, the single and double cup
coffee indicator lights go out, then steam indicator lamp is flashing,
preheating will be finished after steam indicator lamp light on.
3. Put a cup under steam nozzle, let steam nozzle insert into the liquid.
4. Turn on steam knob, release steam.
5. Turn off the steam knob when desired temperature is reached, now steam
is stopped.
Note: Clean steam nozzle immediately after use, to prevent milk scaling.
Caution high temperature of hot water outlet when in use.

12
Indicator Tips
Single-cu
p Coffee
Indicator
Double-c
up Coffee
Indicator
Steam
Indicator
Cause
Solution
Flashing
Flashing
Lights
off
Coffee and hot water
is pre-heating
/
Lights on
Lights on
Lights
off
Coffee and hot water
pre-heating finished
/
Breathing
light on
Lights
off
Lights
off
Making single cup
coffee or water
/
Lights
off
Breathing
light on
Lights
off
Making double cup
coffee
/
Lights
off
Lights
off
Flashing
Steam is pre-heating
/
Lights
off
Lights
off
Lights
on
Steam pre heating
finished
/
Lights
off
Lights
off
Breathin
g light
on
Making steam
/
Lights
off
Lights
off
Lights
on
Steam finished
/
Flashing
quickly
Flashing
quickly
Flashing
quickly
Temperature sensor
short circuit or open
circuit
Please contact
with authorized
service facility for
repairing.
Flashing
quickly
Flashing
quickly
Lights
off
After making the
steam, touch the
steam switch (the
temperature is too
high)
Wait temperature
naturally fall or
open steam button
to making hot
water quick
cooling
Lights
off
Lights
off
Lights
off
Turn off
/
Thermal fuse open
circuit
Please contact
with authorized
service facility for
repairing.

13
Lights
off
Lights
off
Flashing
quickly
Standby for more
than 30 minutes
Touch display
switch
Troulbe Shooting
Problem
Cause/Result
Solution
No water
comes out
Water tank is empty
Pour water in water tank
The input voltage or
frequency is inconsistent
with nameplate
Make sure the voltage and
frequency is consistent with the
nameplate
Machine malfunctions
Please contact with the
authorized service
No steam is
generated
Steam nozzle clogged
Clean steam nozzle
Water tank is empty
Pour water in water tank
Machine malfunctions
Please contact with the
authorized service
Coffee runs
out around
the edge of
the filter
holder
Too much powder in the
filter
Turn off the machine and wait
for it cool down, clean the filter,
then pour appropriate coffee
powder
There is powder in the
seal ring under group
head
Implementation of the
above operation problems
still exist
Please contact with the
authorized service
Coffee
comes out
too slow or
no coffee
comes out
coffee powder is too fine,
and clogged filter
With thicker coffee powder
Filter holes are blocked
Brush / clean the filter
Water tank is not inserted
Insert the water tank in place
Water
leakage on
the bottom
of machine
Drip tray is filled up
Please clean the drip tray
Machine malfunctions
Please contact with the
authorized service
Machine is
The power cord is not
Plug the power cord into a wall

14
not working
plugged well.
outlet correctly,
NTC is short circuit
Please contact with the
authorized service
Machine malfunctions
The steam
cannot froth.
Steam indicator not light
on
Wait steam indicator lights on.
The container is too big or
the shape is not fit
Use high and narrow cup or
garland cup
Used skimmed milk
Use whole milk
*If you have not been able to solve the problem, contact customer support:
frossvt@dg-sunrise.com
Content of hazardous substances in the product
Accessory
Hazardous Substances
(Pb)
(Hg)
(Cd)
(Cr(VI))
(PBBs)
(PBDEs)
Plastic
○
○
○
○
○
○
Hardware
○
○
○
○
○
○
Power
Cord
×
○
○
○
○
○
Electrical
device
×
○
○
○
○
○
Silicone
parts
○
○
○
○
○
○
Package
○
○
○
○
○
○
This form is compiled in accordance with the provisions of SJ/T 11364.
○:Indicates that the content of the hazardous substance in all homogeneous
materials of the part is within the limit requirement of GB/T 26572.
×:It means that the content of the hazardous substance in at least one of the
homogeneous materials of the part exceeds the limit requirement of GB/T
26572.

15
Clean and Maintenance
1. The machine has to be switched off and cooled down;
2. Use a clean damp cloth to clean the stainless steel surface;
Note: Do not use abrasive sponges and alcohol or solvents.
3. Clean the outlet and the seal sing under the group head with
professional brush;
4. Clean steam outlet, confirm there is no blockage
5. Detach the metal funnel through turn it anticlockwise, get rid of
coffee residue inside, then you can clean it with cleanser, but at
last you must rinse with clear water.
6. Clean all the attachments in the water and dry thoroughly.
7. Clean drip tray and removable shelf regularly then dry them.
8. Clean water tank regularly.

16
Cleaning Mineral Deposits
1. The machine builds up lime scale deposits over time, and you
need descale the machine 2-3 months;
2. Pour water and descale in water tank up to MAX capacity (water
and descale ratio is 4:1, follow the instruction of descale. Please use
“household descale”, or you can use the citric acid replace descale
(water and citric acid ratio is 100:3);
3. Lock the filter holder (no coffee powder) into the group head.
According to part “B” MAKE ESPRESSO COFFEE;
4. Touch coffee button, make about 150ml coffee(or Make 3 cups
of coffee) .then touch Steam warm-up switch, it starts preheating ,
open steam knob after steam indicator always lights on, release
steam about 2min and turn off the knob, then make descales
deposit in the machine at least 15min;
5. Repeat the steps 4 for 3 times;
6. Touch double coffee button to brew coffee and repeat the steps
until there is no descale left;
7. Make coffee again(no coffee powder), repeat the steps 4 for 3
times (no need wait for 15 min), then repeat brewing until no water is
left in the boiler;
8. Repeat the step 7 at least 3 times to make sure the piping is
cleanly.

17
Environment friendly disposal
These appliances are built to the very highest of standards.
There are no user serviceable parts. Follow these steps if the unit fails to
operate:
1. Check the instructions have been followed correctly.
2. Check that the mains supply is functional.
3. If the appliance will still not operate, please contact us:
You can help protect the environment!
Please remember to respct the local
regulations: hand in the non-working
electrica equipments to an appropriate
waste disposal center.

Manufacture: FROSSVT Brands Inc
Customer Service: frossvt@dg-sunrise.com
Table of contents
Other Frossvt Coffee Maker manuals