FS FHX Series User manual

FHX Ultra Adapter
Panels User Manual
F
S

For Technical Support: www.fs.com/service.html
Safety Information
Notices:
Try to work in a clean area. Avoid working around heating outlets, as they do a good job of distributing dust everywhere.
Always keep dust caps on connectors and bulkhead adapters as long as possible. Only remove the dust caps to clean
the components prior to making a connection.
Never touch the ferrule end face of a fiber optic connector. No matter what you do, you will leave contamination behind.
Always clean connectors before inserting into an adapter. Use specialized cleaning tools to clean the connectors and
adapters. Specialized cleaning tools make cleaning fast and effective.
F
S
F
S
F
S

For Technical Support: www.fs.com/service.html
Chapter 1 Introduction &Features..................................................... 1
1.1 Introduction ...........................................................................................................................1
1.2 Features ................................................................................................................................1
Chapter 2 Installation ......................................................................... 2
2.1 Assembly View.......................................................................................................................2
2.2 Dimensions............................................................................................................................3
2.3 Installation Procedures ..........................................................................................................3
Contents
S
F
S
F
S
F
S

For Technical Support: www.fs.com/service.html
Chapter 1 Introduction & Features
FHX Series fiber adapter panels are offered in LC, SC and MTP adapters, which are used in conjunction with FHX series
enclosure to provide a means to connect backbone-to-backbone or backbone-to-horizontal fiber cabling.
All fiber adapter panels snap quickly into the front of FHX series fiber enclosures for easy network deployment or moves, adds,
and changes in high density data center.
1
1.1 Introduction
1.2 Features
• Easy one-hand installation and removal, reducing MAC time
• Suitable for FHX series enclosure to allow for future growth
• Snap-in design provides quick and easy installation
S
F
S
F
S
F
S

For Technical Support: www.fs.com/service.html
Chapter 2 Installation
Fiber Retaining Finger
Spring Buckle
2
Figure 2-1
Figure 2-2
Figure 2-3
Dust Cap
LC Fiber Adapter
F
S
F
S
F
S
FHX LC Adapter panel
FHX SC Adapter panel
FHX MTP Adapter panel
2.1 Assembly View
SC Adapter
MTP Adapter

For Technical Support: www.fs.com/service.html 3
Step 1
Figure 2-4
Figure 2-5
2.3 Installation Procedures
133mm
92mm
11.3mm
2.2 Dimensions
The trays shall incorporate rails to facilitate front and rear panel installation while providing a locking mechanism that
secures the module in place.
Option 1: Press the spring buckle at the bottom of panel to insert module from the rear until it locks into place.
Inserting the Fiber Adapter Panel
S
F
S
F
S
F
S

For Technical Support: www.fs.com/service.html 4
Step 2
Installation complete.
Figure 2-7
Figure 2-6
FHX Fiber Enclosures can be converted to support either 8-port or 12-port cassettes and adapters, by moving and changing
the rails.
3-layer pull-style design with rear cable management tray.
Chassis Rails
Sliding Tray Pull-Tabs
Locking Mechanism
Option 2: Fiber adapter Panel also can be installed from the front of the enclosure. Press the locking mechanism to make the
panel moveable if needed.
S
F
S
F
S
F
S

F
S
For Technical Support: www.fs.com/service.html
Addresses, phone number and fax number also have been listed at www.fs.com. Please e-mail us at [email protected] or call us for assistance. All
statements, technical information, and recommendations related to the products here are based upon information believed to be reliable or accurate.
However, the accuracy or completeness thereof is not guaranteed, and no responsibility is assumed for any inaccuracies. Please contact FS.COM for
more information.
For more information
Visit Us at www.fs.com
China
Room 2702, Yisibo Software Building,
Xinhaiyi, No.2 Haitian Road, Yuehai Street,
Nanshan, District, Shenzhen, China
Tel: [phone]
North America
820 SW 34th Street Bldg W7
Suite H, Renton, WA 98057,
United States
Tel: [phone]
Hong Kong
1220 Tung Chun Commercial
Centre, Shanghai Street 438-444,
Kowloon, HongKong
Tel: +(852) 8176 3606
Germany
Building 7, NOVA Neufahrn Gewer
bepark, Am Gfild7, 85375,
Neufahrn bei Freising, Munich
Tel: [phone]