FS VMS-201C User manual

Video Management Server
Video Management Server
VMS - Système de Gestion Vidéo
Quick Start Guide V1.0
Quick-Start Anleitung
Guide de Démarrage Rapide
VMS-201C
HDD
VMS-201C
NET
RUN ALM

Introduction
Accessories
VMS-201C
Thank you for choosing Video Management Server. This guide is designed to familiarize you with
the structure of the Server and describes how to deploy the Server in your network.
EN
1
HDD
VMS-201C
NET
RUN ALM
Common electronic cable x1External power cord x1 High-speed signal cable x1
Mouse x1
Cable connection terminal x6
Mounting bracket component x1 Sheet metal component x1

Ports
ACT
ACT
RS232
RS485
USB3.0
Network interface, used to connect an Ethernet network switch
Serial port, used to interoperate with the connected device
Serial interface, used to debug and maintain the device
Description
Used to connect USB devices such as USB flash drive, USB mouse and USB keyboard
Used to connect an e-SATA disk
e-SATA
ACT 1 LINK RS485
RS232 USB3.0 USB3.0 e-SATA HDMI VGA
ALARM IN
12345678
G G G G G G G 12V1+ 1- 2+ 2- 3+ 3- 4+ 4- 5+ 5- 6+ 6- 7+ 7- 8+ 8-
910 11 12 13 14 15 16 17 18 19 20 21 22 23 24
ACT 2 LINK
10/100/1000 BASE-T
ACT 3 LINK
ACT 4 LINK ALARM OUT ~100-240V;50/60Hz;1A OFF
ON
HDD
VMS-201C
NET
RUN ALM
Back Panel Ports
EN
Hardware Overview
NET
HDD
RUN
ALM
Normal.
Starting up.
Device alarm.
LEDs Description
RUN
ALM
NET Connected to network.
No hard disk, or disk is not connected to power.
No data reading or writing.
Reading or writing data.
Steady on
Blinking
Steady on
State
Steady on
Off
Steady on
Blinking
HDD
Front panel LEDs
2
RS485
RS232 HDMI GND ON/OFF
e-SATA Grounding pointVGA ALARM IN
ALARM OUT
USB3.0 Power supply

Ports
HDMI
ALARM IN
VGA
ALARM OUT
HDMI output, used to connect HDMI interface on a display device
VGA output, used to connect the VGA interface on a display device
24-channel alarm input, used to connect alarm devices such as a magnetic door sensor
Description
8-channel alarm output, used to connect alarm devices such as an alarm siren or
alarm lamp
The 12V (rightmost pin) is the power output
GND
220AC power inputPower supply
Power switchON/OFF
Grounding terminal
Grounding
point
Installation
Please follow the steps if disk installation is necessary. The illustrations are for reference only.
Preparation
1. Prepare a PH2 Philips screwdriver.
2. Prepare an antistatic wrist strap or antistatic gloves during the installation.
Disk Installation
EN
3
NOTE: Please use the SATA disks recommended by the manufacturer. Disconnect power
before installation.

1. Loosen the screws on the rear panel and side panel and remove the upper cover.
2. Attach the 4 gaskets on the brackets.
3. Secure the disk on the brackets by using fixing screws.
EN
4
4. Connect one end of the data cable and power cable to the hard disk.

HDD
NET
RUN ALM
EN
5
5. Place the disk in the chassis and secure it with 4 fixing screws (M3*5).
6. Connect the other end of the data cable and power cable to the motherboard.
HDDNET
RUN ALM

VMS-201C
EN
6
Install the device on a well grounded and securely installed rack. First install two mounting brackets
on the device, and then secure the device on the rack by threading screws through the holes on the
mounting brackets.
Rack Mounting
VMS-201C

Configuring the switch
Start up
Please prepare a monitor and a keyboard. Connect the monitor, mouse, keyboard and then power.
Turn on the power switch on the back panel. The startup takes a while. Please wait patiently.
When the device is started, the login page appears. Use the default username admin and default
password 123456 to log in to the software client. The software client is mainly used for service
operations. Click the help link in the top right corner for help information. When logged in, you
can click the Web icon in the top right corner to access the Web client. The Web client is mainly
used for management and configuration purpose. Click the toolbar at the bottom to switch
between the software client and Web client.
Restart
Right-click on the software client and then choose Restart, or access the Web client and click Restart
on System Configuration>Maintenance>Maintenance.
Shutdown
Use the power switch on the back panel to shut down the device.
7
Login
Guard VMS
English
Login
Forgot Password
admin
******
？
EN

Online Resources
Download
Help Center
Contact Us
https://www.fs.com/products_support.html
https://www.fs.com/service/fs_support.html
https://www.fs.com/contact_us.html
Product Warranty
FS ensures our customers that any damage or faulty items due to our workmanship, we will offer a
free return within 30 days from the day you receive your goods. This excludes any custom made items
or tailored solutions.
Warranty: The Video Management Server enjoys a 2-year limited warranty against defect in
materials or workmanship. For more details about warranty, please check at:
https://www.fs.com/policies/warranty.html
Return: If you want to return item(s), information on how to return can be found at:
https://www.fs.com/policies/day_return_policy.html
2
8
EN

Einführung
Zubehör
VMS-201C
Vielen Dank, dass Sie sich für den Video Management Server entschieden haben. Diese Anleitung
soll Sie mit der Struktur des Servers vertraut machen und beschreibt, wie Sie den Server in Ihrem
Netzwerk einsetzen.
HDD
VMS-201C
NET
RUN ALM
Elektronisches Sammelkabel x1Externes Netzkabel x1 Hochgeschwindigkeitssignalkabel x1
Maus x1
Kabelanschlussklemme x6
Bauteil der Halterung x1 Bauteil aus Blech x1
9
DE