FujiFilm FinePix F30 User manual

THE COMPONENTS IDENTIFIED WITH THE MARK “” ON THE SCHEMATIC
DIAGRAM AND IN THE PARTS LIST ARE CRITICAL FOR SAFETY.
PLEASE REPLACE ONLY WITH THE COMPONENTS SPECIFIED ON THE SCHEMATIC
DIAGRAM AND IN THE PARTS LIST.
IF YOU USE PARTS NOT SPECIFIED, IT MAY RESULT IN A FIRE AND AN
ELECTRICAL SHOCK.
FUJI PHOTO FILM CO., LTD. Ref.No.:ZM00636-100
Printed in Japan 2006.05
DIGITAL CAMERA
FinePix F30
US/EU/EG/EE/AS/CH-Model
SERVICE MANUAL
WARNING
BECAUSE THIS PRODUCTIS RoHS LEAD-FREE COMPLIANT, USE THE DESIG-
NATED AFTER-SELES PARTS AND THE DESIGNATED LEAD-FREE SOLDER WHEN
PERFORMING REPAIRS. (Refer to page 3 to page 5)
CAUTION

2
FinePix F30 Service Manual
7. CAUTION: FOR CONTINUED
PROTECTION AGAINST FIRE
HAZARD, REPLACE ONLY WITH
SAME TYPE 2.5 AMPERES 125V
FUSE.
ATTENTION: AFIN D'ASSURER
UNE PROTECTION
PERMANENTE CONTRE LES
RISQUES D'INCENDIE,
REMPLACER UNIQUEMENT
PAR UN FUSIBLE DE MEME,
TYPE 2.5 AMPERES, 125 VOLTS.
8. WARNING:
TO REDUCE THE ELECTRIC
SHOCK, BE CAREFUL TO
TOUCH THE PARTS.
WARNING!
HIGH VOLTAGE
SAFETY CHECK-OUT
After correcting the original problem, perform the following
safety check before return the product to the customer.
1. Check the area of your repair for unsoldered or poorly
soldered connections. Check the entire board surface
for solder splasher and bridges.
2. Check the interboard wiring to ensure that no wires are
“pinched” or contact high-wattage resistors.
3. Look for unauthorized replacement parts, particularly
transistors, that were installed during a previous repair.
Point them out to the customer and recommend their
replacement.
4. Look for parts which, though functioning, show obvious
signs of deterioration. Point them out to the customer
and recommend their replacement.
5. Check the B + voltage to see it is at the values
specified.
6. Make leakage - current measurements to determine
that exposed parts are acceptably insulated from the
supply circuit before returning the product to the
customer.
2.5A 125V
2.5A 125V
RISK OF FIRE-
REPLACE FUSE
AS MARKED

3
FinePix F30 Service Manual
RoHS lead-free compliance
Because this product is RoHS lead-free compliant, use the designated after-sales parts and the designated lead-free solder
when performing repairs.
<Background & Overview>
With the exception of parts and materials expressly excluded from the RoHS directive (*1), all the internal connections and
component parts and materials used in this product are lead-free compliant (*2) under the European RoHS directive.
*1: Excluded items (list of the main lead-related items)
• Lead included in glass used in fluorescent tubes, electronic components and cathode-ray tubes
• Lead in high-melting-point solder (i.e. tin-lead solder alloys that contain 85% lead or more)
• Lead in ceramic electronic parts (piezo-electronic devices)
• Mercury contained in fluorescent tubes is also excluded.
*2: Definition of lead-free
A lead content ratio of 0.1 wt% or less in the applicable locations (solder, terminals, electronic components, etc.)
<Reference>
RoHS: The name of a directive issued by the European Parliament aimed at restricting the use of
certain designated hazardous substances included in electrical and electronic equipment.
Designated substances (6): Lead, mercury, cadmium, hexavalent chromium, polybrominated biphenyls (PBBs) and
polybrominated diphenyl ether (PBDE)
<Lead-free soldering>
When carrying out repairs, use a designated lead-free solder, bearing in mind the differing work practices for conventional
solder (eutectic) and lead-free solder.


Differences in the soldering work for lead-free and eutectic solder
When the soldering work practices for eutectic solder and lead-free solder are compared, the main differences are as shown
below. In particular, when lead-free solder is used, the solder tends to be less workable than when eutectic solder is used.
Accordingly, the soldering techniques used must take that into account.
Difference
The solder starts melting later.
Poor wetting
Solder feed rate is difficult to control.
Wetting the insides of through holes is especially
difficult.
During repairs (or modifications) removing solder
from inside through holes is difficult.
There is serious carbonization of the soldering iron.
The surface is not glossy.
1
2
3
4
5
6
7
Countermeasure
The initial melting point of lead-free solder is high, so you
have to get used to it.
Move the tip of the soldering iron around to heat the entire
connection to the melting temperature and assist wetting.
Use the solder (wire) diameter and soldering iron that are
best suited to connection being soldered.
First apply solder to the area immediately around the
through hold and then feed the solder into the hole.
Use a suitable wicking wire (with a suitable method and
heating) and a suction tool.
Either put solder onto the soldering iron tip after completing
the work, or turn the iron off frequently.
Learn to recognize the appearance of the surface.

4
FinePix F30 Service Manual


Setting temperature during lead-free soldering
• Lead-free solder melting temperature
The melting point of eutectic (Sn-Pb) solder is 183°C, while the melting point of lead-free solder (Sn-Ag-Cu) is 30°C higher
at 220°C.
• Soldering iron tip temperature
The temperature setting for the soldering iron used should be such that the tip of the soldering iron is at the correct
bonding temperature for the connection. This temperature is normally set at around 100°C higher than the melting point of
the solder.
However, the actual temperature should take into account the shape and size of the soldering iron tip, the heat tolerance
of the connection and the workability of that temperature.
• Correct bonding temperature
The correct bonding temperature refers not to the temperature of the heat source, but to the bonding temperature that will
give the best bond strength.


Precautions when soldering with lead-free solder
• Soldering iron maintenance
Because of the high soldering iron temperature in lead-free soldering, there is rapid carbonization of the flux adhering to
the tip of the soldering iron.
(1) Always cover the tip of the soldering iron with solder when it is not being used.
(2) If the tip is black from carbonization, wipe it gently with a paper towel soaked in alcohol until the solder will wet.
• Uniform heating of the board and components
To ensure that the lead-free solder wets the entire surface of the pattern and the lands despite its poor wetting
characteristics, you must move the tip of the soldering iron over a wide area to raise the temperature of the entire
connection.


Soldering iron
A soldering iron with a temperature control is best.

5
FinePix F30 Service Manual
lead-free
Wire diameter 0.8mm
Solder type (Displayed symbol)
SnAgCu


Solder wire (thread)
Use the lead-free solders specified below.
Solder type: Sn96.5Ag3Cu0.5 (Displayed symbol: SnAgCu)
Wire diameter: 0.6, 0.8 or 1.0 mm
Sample:


Flux
Conventional flux can be used.


Solder application wires (mesh, wicking wire, etc.)
Conventional application wires can be used.

6
FinePix F30 Service Manual
MEMO

7
CONTENTS
FinePix F30 Service Manual
CONTENTS
1. General ........................................................... 8
1-1. Product specification .............................................. 8
1-2. Explanation of Terms ............................................ 11
1-3. Names of External Components .......................... 12
2. Disassembly ................................................. 13
2-1. Names of internal Components ............................ 13
2-2. Removing the R PANEL CONST .......................... 14
2-3. Disassembling the R PANEL CONST .................. 15
2-4. Removing the MAIN PWB ASSY .......................... 16
2-5. Removing the FLASH CONST ............................. 17
2-6. Removing the LENS ASSY .................................. 17
2-7. Removing the BATTERY HOLDER ASSY ........... 18
2-8. Removing the OPE UNIT ..................................... 18
2-9. Specifications for the sheet component
attachment locations ............................................ 19
2-9-1. Affixing the SHEET (PWB) to the
MAIN PWB ASSY. ................................... 19
2-9-2. Affixing the TR SHEET, EMI SHEET and
UL TAPE to the R PANEL CONST.......... 19
2-9-3. Affixing the UL TAPE to the
LEAD E.CAP. .......................................... 20
3. Schematics ................................................... 21
3-1. Cautions ............................................................... 21
3-2. Basic Block Names and Functions ....................... 21
3-3. Description of Main Block Functions .................... 22
3-3-1. Technical Overview ................................. 22
3-4. Block Diagram ...................................................... 23
3-5. Overall connection Diagram ................................. 24
3-6. Circuit Diagrams ................................................... 25
3-6-1. CAMERA BLOCK ................................... 25
3-6-2. DC/DC BLOCK ....................................... 26
3-6-3. FLASH BLOCK ....................................... 27
3-6-4. KEY BLOCK ........................................... 28
3-6-5. LCD BLOCK ........................................... 29
3-6-6. MOTOR BLOCK ..................................... 30
3-6-7. PMG BLOCK .......................................... 31
3-6-8. PROCESS BLOCK (IO) .......................... 32
3-6-9. PROCESS BLOCK (PW) ........................ 33
3-6-10. PROCESS BLOCK (SYS) ...................... 34
3-6-11. AUDIO BLOCK ....................................... 35
3-6-12. CCD FPC BLOCK ................................... 36
3-6-13. CHG BLOCK ........................................... 37
3-6-14. IO BLOCK ............................................... 38
3-6-15. LED BLOCK ............................................ 39
3-6-16. MEDIA BLOCK ....................................... 39
3-6-17. VIDEO BLOCK ....................................... 40
3-7. Mounted Parts Diagrams ...................................... 42
3-7-1. CCD FPC ASSY ..................................... 42
3-7-2. MAIN PWB ASSY ................................... 45
4. Adjustments .................................................. 47
4-1. Important point before Adjustment ....................... 47
4-1-1. The handling of image files in internal
memory ................................................... 47
4-1-2. Adjustment when Replacing
Major Parts ............................................. 48
4-2. Measuring Instruments Used ............................... 48
4-4. Calibration method of pattern box ........................ 49
4-3. Use Jig list ............................................................ 49
4-5. Adjustment software installation ........................... 50
4-5-1. Various downloading software
decompressions, preservation methods,
and notes ................................................ 50
4-5-2. Installation of DSC jig driver ................... 51
4-5-3. Adjustment softwareinitiation method ..... 51
4-6. Initial Settings of the Adjustment Software ........... 52
4-7. Starting the Adjustment Software ......................... 55
4-8. [R] : Flash Memory Reset ..................................... 58
4-9. [F4] : CCD Defect Correction/OFD Adjustment .... 60
4-10. [F5] : Camera Adjustment ..................................... 64
4-11. [F6] : AF Adjustment ............................................. 70
4-12. [F7] : Flash Adjustment ......................................... 73
4-13. [F1] : Battery Voltage Adjustment ......................... 75
4-14. [F11] : Video Adjustment ...................................... 79
4-15. [F3] : LCD Adjustment .......................................... 81
4-16. [F8] : Firmware Download .................................... 83
4-17. [F12] : End Setting ................................................ 85
5. Inspection ..................................................... 89
5-1. Required Measuring Equipment ........................... 89
5-2. Connection of Measuring Equipment ................... 89
5-3. Inspection and Factory Settings ........................... 90
6. Parts List....................................................... 94
6-1. Packing and Accessories ..................................... 94
6-1-1. US-model ................................................ 94
6-1-2. EU-model ................................................ 95
6-1-3. EU-model (JP Production) ...................... 96
6-1-4. EG-model ................................................ 97
6-1-5. EE-model ................................................ 98
6-1-6. AS-model ................................................ 99
6-1-7. AS-model (JP Production) .................... 100
6-1-8. CH-model .............................................. 101
6-1-9. CH-model (JP Production) .................... 102
6-2. Mecha Block ....................................................... 103
6-2-1. US/AS-model ........................................ 103
6-2-2. EU/EG/EE-model .................................. 104
6-2-3. EU-model (JP Production) .................... 105
6-2-4. CH-model .............................................. 106
6-2-5. AS/CH-model (JP Production) .............. 107
6-3. Electrical parts .................................................... 109
7. Appendix..................................................... 110
7-1. List of Related Technical Updates Issued .......... 110

8
1. General FinePix F30 Service Manual
1. General
1-1. Product specification
System
Model Digital camera FinePix F30
Effective pixels 6.3 million pixels
CCD 1/1.7-inch Super CCD HR
Storage media Internal memory (approx. 10 MB)/xD-Picture Card (16/32/64/128/256/512 MB/1 GB)
File format Still image: DCF-compliant
Compressed: Exif ver.2.2 JPEG, DPOF-compatible
*Design rule for Camera File System compliant DPOF compatible
Movie: AVI format, Motion JPEG
Audio: WAVE format, Monaural sound
Number of recorded pixels Still image: 2848 × 2136 pixels/3024 × 2016 pixels/2048 × 1536 pixels/
1600 × 1200 pixels/640 × 480 pixels ( / / / / )
Lens Fujinon 3
× optical zoom lens
F2.8-F5
Focal length f=8 mm-24 mm
(Equivalent to approx. 36 mm-108 mm on a 35 mm camera)
(: Equivalent to approx. 37mm-111 mm on a 35 mm camera)
Digital zoom Approx. 6.2 × (3 × optical zoom lens is used together: Max. zoom scale: approx. 18.5 × )
Aperture (Wide-angle) F2.8 to F8 (Up to 10 steps)
Focal range Normal: approx. 60 cm (2.0 ft.) to infinity
Macro: wide-angle: approx. 5 cm (2.0 in.) to 80 cm (2.6 ft.)
telephoto: approx. 30 cm (1.0 ft.) to 80 cm (2.6 ft.)
Sensitivity AUTO/AUTO(400)/AUTO(1600)/Equivalent to ISO 100/200/400/800/1600/3200
Photometry TTL 256-zones metering Multi, Spot, Average
Exposure control Program AE/Aperture priority AE/Shutter priority AE
Scene position (NATURAL LIGHT), (NATURAL & ), (PORTRAIT), (LANDSCAPE),
(SPORT), (NIGHT), (FIREWORKS), (SUNSET), (SNOW), (BEACH),
(UNDERWATER), (MUSEUM), (PARTY), (FLOWER), (TEXT)
Exposure compensation -2 EV to +2 EV in 1/3 EV-step increments ( , A/S)
Shutter speed 3 sec. to 1/2000 sec. (depend on Exposure mode)
*When the scene position is at NIGHT, it is possible to have long exposure times of 1 to
15 seconds.
Continuous shooting Top-3: Number of recorded frames: up to 3 frames
(Max. 2.2 frames/sec.)
Final-3: Number of recorded frames:
Last 3 frames before releasing the shutter button
(Max. 2.2 frames/sec.)
Long-period: Number of recorded frames: Depend on memory size. 1.5 sec. interval at
N depending on quality level.
(Max. 0.9 frames/sec.)
Focus Mode: Single-AF, Continuous AF
AF system: TTL contrast-type
AF frame selection: AF (CENTER), AF (MULTI)
White balance Automatic scene recognition/Preset (Fine, Shade, Fluorescent (Daylight), Fluorescent
(Warm White), Fluorescent (Cool White), Incandescent) /Custom
Self-timer Approx. 2 sec./10 sec.

9
1. General
FinePix F30 Service Manual
System
Flash type Auto flash
Effective range: ( : AUTO): Wide-angle: approx. 60 cm-6.5 m (2.0 ft.-21.3 ft.)
Telephoto: approx. 60 cm-3.5 m (2.0 ft.-11.5 ft.)
Macro: approx. 30 cm-80 cm (1.0 ft.-2.6 ft.)
Flash mode Auto, Red-eye Reduction, Forced Flash, Suppressed Flash, Slow Synchro, Red-eye
Reduction + Slow Synchro
LCD monitor 2.5 inches, Aspect ratio: 4:3; 230,000 pixels Amorphous silicon TFT, Approx. 100%
coverage
Movie 640
× 480 pixels/320 × 240 pixels ( / )
(30 frames per second with monaural sound)
A series of continuous image can be recorded depending on the available space on an
xD-Picture Card or internal memory. Zoom cannot be used during movie recording.
Photography functions High-speed shooting, Best framing, Post shot assist window, Frame No. memory
Playback functions Trimming, Automatic playback, Multi-frame playback, Sorting by date, Image rotate, Voice
memo
Other functions PictBridge, Exif print, Language ( , English, Francais, Deutsch, , Italiano,
, , , , , Nederlands, ), Time difference, FinePix
photo mode ( -mode)
Input/Output Terminal
A/V OUT NTSC/PAL-type (with monaural sound)
(Audio/Visual output)
Digital input/output USB 2.0 High-Speed/PTP (Picture Transfer Protocol)
DC input socket AC Power Adapter AC-5VC (included)/AC-5VX (sold separately)
Power Supply and Others
Power supply Rechargeable Battery NP-95
According to the CIPA (Camera & Imaging Products Association) standard procedure for
measuring digital still camera battery consumption (extract):
When using a battery, use the battery supplied with the camera. The storage media should
be xD-Picture Card.
Pictures should be taken at a temperature of +23°C (+73°F), with the LCD monitor turned
on, the optical zoom moved from full wide-angle to full telephoto (or vice-versa) and back
again to its original position every 30 seconds, the flash used at full power every second
shot and the camera turned off and then on again once every 10 shots.
• Note: Because the number of available shots varies depending on the level of charge in
the battery, the figures shown here for the number of available shots using the
battery is not guaranteed.
The number of available shots will also decline at low temperatures.
Camera dimensions 92.7 mm
× 56.7 mm × 27.8 mm/3.6 in. × 2.2 in. × 1.1 in.
(W/H/D) (not including accessories and attachments)
Camera mass (weight) Approx. 155 g/5.5 oz. (not including accessories, battery and xD-Picture Card)
Weight for photography Approx. 195 g/6.9 oz. (including battery and xD-Picture Card)
Operating conditions Temperature: 0oC to +40oC (+32oF to +104oF)
80% humidity or less (no condensation)
Guide to the number of
available frames for battery
operation
NP-95 (1800 mAh) Approx. 500 frames
Battery Type Number of frames

10
1. General FinePix F30 Service Manual
Accessories included zRechargeable Battery NP-95 (1)
zStrap (1)
zAC Power Adapter AC-5VC (1 set)
zA/V cable for FinePix F30 (1) Including plug to pin-plug
× 2
zUSB cable for FinePix F30 (1)
zCD-ROM (1) Software for FinePix CX
zOwner’s Manual (1)
Optional accessories zxD-Picture Card
16MB/32MB/64MB/128MB/256MB/512MB/1GB
zBattery Charger BC-65S
zRechargeable Battery NP-95 (1800 mAh)
zAC Power Adapter AC-5VX
zSoft Case SC-FXF30
zImage Memory Card Reader DPC-R1
• Compatible with xD-Picture Card of 16 MB to 512 MB, and SmartMedia of 3.3 V,
4 MB to 128 MB.
zPC Card Adapter DPC-AD
• Compatible with xD-Picture Card of 16 MB to 512 MB, and SmartMedia of 3.3 V,
2 MB to 128 MB.
zCompactFlash Card Adapter DPC-CF
zWaterproof Case WP-FXF30
Power Supply and Others
Standard number of available frames/recording time per xD-Picture Card and internal memory
The number of available frames, recording time or file size varies slightly depending on the subjects photographed. Note also
that the divergence between standard number of frames and the actual number of frames is greater for
xD-Picture Cards with higher capacities.
Quality setting
16 MB
32 MB
64 MB
128 MB
256 MB
Image data size
Number of recorded pixels
F
2848 2136
3024 2016 2048 1536 1600 1200 640 480 640 480 320 240
N(30 fps) (30 fps)
5
10
21
42
85
3.0 MB
512 MB
170
10
6
20
42
84
169
1.5 MB
339
10
20
42
84
169
1.5 MB
339
19
40
81
162
325
780 KB
651
25
50
101
204
409
630 KB
818
12
61215 77
2
247
497
997
1997
130 KB
3993
13 sec.
27 sec.
55 sec.
111 sec.
223 sec.
7.4 min.
26 sec.
54 sec.
109 sec.
219 sec.
7.3 min.
Internal memory (approx. 10 MB)
3
8 sec. 16 sec.
14.6 min.
1 GB
341 680 680 1305 1639 7995
14.9 min. 29.3 min.

11
1. General
FinePix F30 Service Manual
1-2. Explanation of Terms
EV: A number denotes Exposure Value. The EV is determined by the brightness of the subject
and sensitivity (speed) of the film or CCD. The number is larger for bright subjects and
smaller for dark subjects. As the brightness of the subject changes, a digital camera
maintains the amount of light hitting the CCD at a constant level by adjusting the aperture
and shutter speed.
When the amount of light striking the CCD doubles, the EV increases by 1. Likewise, when
the light is halved, the EV decreases by 1.
Frame rate (fps): The frame rate refers to the number of images (frames) that are photographed or played
back per second. For example, when 10 frames are continuously photographed in a 1-
second interval, the frame rate is expressed as 10 fps.
For reference, TV images are displayed at 30 fps (NTSC).
JPEG: Joint Photographic Experts Group
A file format used for compressing and saving color images. The higher the compression
rate, the greater the loss of quality in the decompressed (restored) image.
Motion JPEG: A type of AVI (Audio Video Interleave) file format that handles images and sound as a
single file. Images in the file are recorded in JPEG format. Motion JPEG can be played
back by QuickTime 3.0 or later.
Smear: A phenomenon specific to CCDs whereby white streaks appear on the image when there
is a very strong light source, such as the sun or reflected sunlight, in the photography
screen.
WAVE A standard format used on Windows systems for saving audio data. WAVE files have the
“.WAV” file extension and the data can be saved in either compressed or uncompressed
format. Uncompressed recording is used on this camera.
WAVE files can be played back on a personal computer using the following software:
Windows: MediaPlayer
Macintosh: QuickTime Player
* QuickTime 3.0 or later
White Balance: Whatever the kind of the light, the human eye adapts to it so that a white object still looks
white. On the other hand, devices such as digital cameras see a white subject as white by
first adjusting the color balance to suit the color of the ambient light around the subject.
This adjustment is called matching the white balance.
Exif Print: Exif Print Format is a newly revised digital camera file format that contains a variety of
shooting information for optimal printing.

12
1. General FinePix F30 Service Manual
1-3. Names of External Components
Shutter button
Mode dial
Lens (lens cover)
POWER button Flash
AF-assist illuminator
Self-timer lamp
Terminal cover
A/V OUT (Audio/
Visual output) socket
USB socket
DC IN 5V socket
Microphone
Indicator lamp
4-direction
( ) button
LCD monitor
Speaker
Tripod mount
W (Wide zoom) button
T (Tele zoom) button
(Playback) button
Photo mode ( ) button
Strap mount
MENU/OK button
Exposure compensation
button
DISP (Display)/BACK button
Battery cover
xD-Picture Card slot
Battery compartment
Battery release catch

13
2. Disassembly
FinePix F30 Service Manual
2. Disassembly
2-1. Names of internal Components
LENS ASSY
LED
E CAP
MIC ASSY
F PANEL ASSY
MAIN PWB ASSY
KEY FPC
GUM KEY
SPEAKER ASSY
BATTERY HOLDER ASSY FLASH CONST
R PANEL ASSY
LCD CONST
FRAME REAR
OPE UNIT

14
2. Disassembly FinePix F30 Service Manual
2-2. Removing the R PANEL CONST
(1) Remove the 2 special screws (M1.7 x 2.5).
(2) Remove the 3 screws (M1.7 x 3.0).
(3) Remove the 2 screws (M1.7 x 4.0).
(4) Lift off the R PANEL CONST in the direction of the
arrow.
(5) Remove the 2 FPC from the connectors in the
direction of the arrow.
[Notes on Assembly]
Take care not to trap or pinch the LCD FPC during
assembly.
[Assembly]
Assemble by performing the disassembly procedure in
reverse.
1
3
4
2
5
5

15
2. Disassembly
FinePix F30 Service Manual
2-3. Disassembling the R PANEL CONST
(1) Peel off the EMI SHEET.
(2) Peel off the UL TAPE.
(3) Peel off the TR SHEET.
(4) Remove the 8 screws (M1.4 x 2.5).
(5) Remove the REAR FRAME.
5
3
2
1
4
6
6
6
(6) Remove the KEY FPC, KEY GUM and LCD CONST.
[Notes on Assembly]
Take care not to trap or pinch the BACK LIGHT FPC
during assembly.
[Assembly]
Assemble by performing the disassembly procedure in
reverse.

16
2. Disassembly FinePix F30 Service Manual
1
2
10
11
12
3
5
8
9
4
6
7
2-4. Removing the MAIN PWB ASSY
(1) Remove the SHEET (PWB).
(2) Discharge the main capacitor.
Take care not to touch the main capacitor terminals
before discharging the capacitor.
(3) Unlock the connector and remove the LENS FPC.
(4) Unlock the connector and remove the OPE UNIT
FPC.
(5) Unlock the connector and remove the CCD FPC.
(6) Remove the wire harness (SPEAKER) from the
connector.
(7) Remove the wire harness (MIC) from the connector.
(8) Remove the screw (M1.7 x 3.0).
(9) Remove the 3 screws (M1.7 x 4.0).
(10) Remove the PLATE L.
(11) Open the BATTERY COVER.
(12) Remove the MAIN PWB ASSY in the direction of the
arrow.
[Notes on Assembly]
With the JACK COVER pulled off, fit the MAIN PWB ASSY
and assemble so that the wiring runs between the FLASH
CONST and the MAIN PWB ASSY.
[Assembly]
Assemble by performing the disassembly procedure in
reverse.

17
2. Disassembly
FinePix F30 Service Manual
2-5. Removing the FLASH CONST
(1) Remove the solder on the MAIN PWB ASSY (2
locations) and remove the LED.
(2) Remove the solder on the MAIN PWB ASSY (2
locations) and remove the LEAD C.CAP.
(3) Remove the solder on the MAIN PWB ASSY (3
locations) and remove the FLASH CONST.
2
3
1
9.5mm~10.5mm
K
2
1
[Assembly]
Assemble by performing the disassembly procedure in
reverse.
* When replacing the LED, cut the leads to a length
between 9.5 and 10.5 mm for installation.
2-6. Removing the LENS ASSY
(1) Remove the 3 screws (M1.7 x 7.0).
(2) Remove the LENS ASSY in the direction of the arrow.
[Assembly]
Assemble by performing the disassembly procedure in
reverse.

18
2. Disassembly FinePix F30 Service Manual
1
1
2
2-7. Removing the BATTERY HOLDER ASSY
(1) Remove the BATTERY HOLDER ASSY in the
direction of the arrow.
[Notes on Assembly]
Run the SPEAKER ASSY • MIC ASSY leads along the
BATTERY HOLDER groove.
[Assembly]
Assemble by performing the disassembly procedure in
reverse.
2-8. Removing the OPE UNIT
(1) Remove the screw (M1.4 x 1.6).
(2) Remove the OPE UNIT in the direction of the arrow.
[Assembly]
Assemble by performing the disassembly procedure in
reverse.

19
2. Disassembly
FinePix F30 Service Manual
2-9. Specifications for the sheet component attachment locations
2-9-1. Affixing the SHEET (PWB) to the MAIN PWB ASSY.
Affix the sheet so that it completely covers the specified area,
with the top and left sides securely folded back and stuck in
place.
2-9-2. Affixing the TR SHEET, EMI SHEET and UL TAPE to the R PANEL CONST
Affix the TR SHEET so that the alumite butts against the
laser-ablated section and stick a piece of UL TAPE cut to a
size of 19 mm x 13 ± 2 mm as shown in the figure on the
right so that it completely covers the TR SHEET.

20
2. Disassembly FinePix F30 Service Manual
13 2mm
2-9-3. Affixing the UL TAPE to the LEAD E.CAP.
Cut the UL TAPE to a size of 19 mm x 13 ± 2 mm and stick it
onto the LEAD E.CAP so that it covers the section adjacent
to the metal terminals for the DC-JACK on the MAIN PWB
ASSY.