Fujifilm Finepix s20 pro User manual

This manual will show you how to use your FUJIFILM

DIGITAL CAMERA FinePix S20 Pro correctly.

Please follow the instructions carefully.

BL00291-200(1)

Getting Ready Using

the Camera

Advanced

Features

Software

Installation

Settings Viewing Images

2 3

EC Declaration of Conformity

Name:Fuji Photo Film (Europe)G.m.b.H.

Address:Heesenstrasse 31

40549 Dusseldorf, Germany

declare that the product

Product Name: FUJIFILM DIGITAL CAMERA FinePix S20 Pro

Manufacture’s Name: Fuji Photo Film Co., Ltd.

Manufacture’s Address: 26-30, Nishiazabu 2-chome, Minato-ku,

Tokyo 106-8620, Japan

is in conformity with the following Standards

Safety:EN60065

EMC:EN55022:1998 Classe B

EN55024:1998

EN61000-3-2:1995 +A1:1998 +A2:1998

following the provision of the EMC Directive (89/336/EEC, 92/31/EEC and

93/68/EEC)and Low Voltage Directive (73/23/EEC).

Dusseldorf, Germany February 1, 2004

Place Date Signature/Managing Director

Bij dit produkt zijn batterijen geleverd. Wanneer deze leeg zijn, moet u

ze niet weggooien maar inleveren als KCA

Warning

IMPORTANT Be sure to read this page before using the Software.

For customers in the U.S.A.

Tested To Comply

With FCC Standards

FOR HOME OR OFFICE USE

FCC Statement

This device complies with part 15 of the FCC Rules. Operation

is subject to the following two conditions: (1) This device may

not cause harmful interference, and (2) this device must

accept any interference received, including interference that

may cause undesired operation.

CAUTION

This equipment has been tested and found to comply with the

limits for a Class B digital device, pursuant to Part 15 of the

FCC Rules. These limits are designed to provide reasonable

protection against harmful interference in a residential

installation. This equipment generates, uses, and can radiate

radio frequency energy and, if not installed and used in

accordance with the instructions, may cause harmful

interference to radio communications. However, there is no

guarantee that interference will not occur in a particular

installation. If this equipment does cause harmful interference

to radio or television reception, which can be determined by

turning the equipment off and on, the user is encouraged to try

To prevent fire or shock hazard, do not expose the unit to rain or moisture.

to correct the interference by one or more of the following

measures:

— Reorient or relocate the receiving antenna.

— Increase the separation between the equipment and receiver.

— Connect the equipment into an outlet on a circuit different from

that to which the receiver is connected.

— Consult the dealer or an experienced radio/TV technician for

help.

You are cautioned that any changes or modifications not

expressly approved in this manual could void the user’s authority

to operate the equipment.

Notes on the Grant:

To comply with Part 15 of the FCC rules, this product must be

used with a Fujifilm-specified ferrite-core A/V cable, USB cable

and DC supply cord.

For customers in Canada

CAUTION

This Class B digital apparatus complies with Canadian ICES-003.

Please read the Safety Notes (➡P.118) and make

sure you understand them before using the camera.

NOTICE

BEFORE OPENING THE PACKAGE OF CD-ROM

PROVIDED BY FUJI PHOTO FILM CO., LTD., PLEASE

READ THIS END USER LICENSE AGREEMENT

CAREFULLY. ONLY IF YOU DO AGREE TO THIS

AGREEMENT, YOU WILL BE ABLE TO USE THE

SOFTWARE RECORDED ON THE CD-ROM. BY OPENING

THE PACKAGE, YOU ACCEPT AND AGREE TO BE

BOUND BY THIS AGREEMENT.

End User License Agreement

his End User License Agreement (“Agreement”) is an agreement between

Fuji Photo Film Co., Ltd. (“FUJIFILM”) and you, which sets forth the terms

and conditions of the license granted for you to use the software provided by

FUJIFILM.

The CD-ROM contains third party software. In case a separate agreement is

provided by a third party supplier for its software, the provisions of such

separate agreement shall apply to the use of such third party software,

prevailing over those of this Agreement.

1. Definitions.

(a) “Media” means the CD-ROM titled “Software for FinePix SX” which is

provided to you together with this Agreement.

(b) “Software” means the software which is recorded on Media.

related written materials which are provided to you together with

Media.

(d) “Product” means Media (including Software) and Documentation

collectively.

2. Use of Software.

FUJIFILM grants to you a nontransferable, nonexclusive license:

(a)

to install one copy of Software onto one computer in binary machine

executable form;

(b) to use Software on the computer onto which Software is installed;

and

3. Restrictions.

3.1 You shall not distribute, rent, lease or otherwise transfer all or any

part of Software, Media or Documentation to any third party without

FUJIFILM’s prior written consent. You also shall not sublicense,

assign or otherwise transfer all or any part of the rights granted to

you by FUJIFILM under this Agreement without FUJIFILM’s prior

written consent.

3.2 Except as expressly granted by FUJIFILM hereunder, you shall not

copy or reproduce all or any part of Software or Documentation.

3.3 You shall not modify, adapt or translate Software or Documentation.

You also shall not alter or remove copyright and other proprietary

notices that appear on or in Software or Documentation.

3.4 You shall not, or shall not have any third party, reverse-engineer,

decompile, or disassemble Software.

4. Ownership.

All copyrights and other proprietary rights to Software and

Documentation are owned and retained by FUJIFILM or the third party

suppliers as indicated on or in Software or Documentation. Nothing

contained herein shall be construed, expressly or implicitly, as

transferring or granting any right, license, or title to you other than those

explicitly granted under this Agreement.

5. Limited Warranty.

FUJIFILM warrants to you that Media is free from any defect in material

and workmanship under normal use for ninety (90) days from the date of

your receipt of Media. Should Media not meet the foregoing warranty,

FUJIFILM shall replace such defective Media with other Media bearing

no defect. FUJIFILM’s entire liability and your sole and exclusive remedy

with regard to any defect in Media shall be expressly limited to such

FUJIFILM’s replacement of Media as provided herein

6. DISCLAIMER OF WARRANTY.

EXCEPT AS PROVIDED IN SECTION 5 HEREIN, FUJIFILM

PROVIDES PRODUCT “AS IS” AND WITHOUT WARRANTIES OF

ANY KIND, EXPRESS OR IMPLIED. FUJIFILM SHALL MAKE NO

WARRANTY, EXPRESS, IMPLIED OR STATUTORY, AS TO ANY

OTHER MATTERS, INCLUDING, BUT NOT LIMITED TO NON-

INFRINGEMENT OF ANY COPYRIGHT, PATENT, TRADE SECRET,

OR ANY OTHER PROPRIETARY RIGHTS OF ANY THIRD PARTY,

MARCHANTABILITY, OR FITNESS FOR ANY PARTICULAR

PURPOSE.

7. LIMITATION OF LIABILITY.

IN NO EVENT SHALL FUJIFILM HAVE ANY LIABILITY FOR ANY

GENERAL, SPECIAL, DIRECT, INDIRECT, CONSEQUENTIAL,

INCIDENTAL, OR OTHER DAMAGES (INCLUDING DAMAGES FOR

LOSS OF PROFITS OR LOST SAVINGS) INCURRED FROM THE USE

OF OR INABILITY TO USE PRODUCT EVEN IF FUJIFILM HAS BEEN

ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.

8. No export.

You acknowledge that neither Software nor any part thereof, will be

transferred, or exported to any country or used in any manner in

violation of any export control laws and regulations to which Software is

subject.

9. Termination.

In case you breach any of the terms and conditions hereof, FUJIFILM

may immediately terminate this Agreement without any notice.

10. Term.

This Agreement is effective until the date when you cease to use

Software, unless earlier terminated in accordance with Section 9

hereof.

11. Obligation upon termination.

Upon termination or expiration of this Agreement, you shall, at

your own responsibility and expense, delete or destroy

immediately all Software (including its copies), Media and

Documentation.

12. Governing Law.

This Agreement shall be governed by and construed in

accordance with laws of Japan.

4 5

Getting Ready Using

the Camera

Advanced

Features Settings Software

Installation Viewing Images

Contents

ATTACHING THE LENS CAP AND STRAP ................................................................................................................... 10

LOADING THE BATTERIES ........................................................................................................................................... 12

INSERTING THE MEDIA ................................................................................................................................................ 14

CHECKING THE BATTERY CHARGE ........................................................................................................................... 15

TURNING ON AND OFF / SETTING THE DATE AND TIME ......................................................................................... 16

CORRECTING THE DATE AND TIME / CHANGING THE DATE ORDER .................................................................... 17

SELECTING THE LANGUAGE ...................................................................................................................................... 18

Warning .......................................................................... 2

IMPORTANT .................................................................. 2

EC Declaration of Conformity ......................................... 3

Preface ........................................................................... 6

Accessories included ...................................................... 7

Camera parts and features ............................................. 8

Example of screen text display .................................. 9

■Still photography mode ..................................... 9

■Playback mode .................................................. 9

System Expansion Options ....................................... 105

Accessories Guide .................................................... 106

Using Your Camera Correctly ................................... 107

Power Supply and Batteries ...................................... 107

Applicable Batteries .............................................. 107

Notes on the Batteries ........................................... 107

Using the AA-size Ni-MH batteries correctly ......... 108

AC Power Adapter ................................................ 108

Procedure for discharging rechargeable Ni-MH batteries

... 109

Notes on the Media (xD-Picture Card™ and Microdrives)

... 110

Warning Displays ...................................................... 111

Troubleshooting ......................................................... 113

Specifications ............................................................ 115

Explanation of Terms ................................................ 117

Safety Notes .............................................................. 118

1 Getting Ready

SET-UP ........................................................................................................................................................................... 83

■SET-UP menu options ..................................................................................................................................... 83

USING THE SET-UP SCREEN .......................................................................................................................... 83

IMAGE DISPLAY ................................................................................................................................................ 84

Preview zoom / Displaying information for photographed images / Continuous shooting preview (image checking)

.. 85

POWER SAVE SETTING (low power setting) .................................................................................................... 86

FORMAT (media initialization) ............................................................................................................................ 86

ADAPTER SETTING .......................................................................................................................................... 87

FRAME NO. (frame number storage) ................................................................................................................. 88

CCD-RAW ........................................................................................................................................................... 88

4 Settings

5.1 THE SOFTWARE COMPONENTS ........................................................................................................................... 89

5.2 INSTALLATION ON A Windows PC ......................................................................................................................... 90

5.3 INSTALLATION ON A Mac OS 9.0 TO 9.2 ............................................................................................................... 92

5.4 INSTALLATION ON A Mac OS X ............................................................................................................................. 95

5 Software Installation

6.1 CAMERA CONNECTION ......................................................................................................................................... 98

6.2 USING FinePixViewer ............................................................................................................................................. 103

6 Viewing Images

BASIC OPERATION GUIDE ........................................................................................................................................... 19

LCD monitor brightness / Volume adjustment .................................................................................................... 22

TAKING PICTURES (AUTO MODE) .............................................................................................................................. 23

INDICATOR LAMP DISPLAY ............................................................................................................................. 26

NUMBER OF AVAILABLE FRAMES .................................................................................................................. 26

USING AF/AE LOCK .......................................................................................................................................... 27

USING THE ZOOM (OPTICAL ZOOM / DIGITAL ZOOM) ................................................................................. 28

BEST FRAMING ................................................................................................................................................. 28

VIEWING THE IMAGES (PLAYBACK) ........................................................................................................................... 29

Single-frame playback / Fast-forwarding through the images / Multi-frame playback ........................................ 29

Single-frame playback / Playback zoom / Panning / Trimming ........................................................................... 30

ERASING IMAGES (ERASE FRAME) ............................................................................................................................ 31

PLAYBACK MODE

STILL PHOTOGRAPHY MODE

2 Using the Camera

BSTILL PHOTOGRAPHY / MOVIE

yQUALITY MODE (NUMBER OF RECORDED PIXELS) ................................................................................................. 32

Quality settings in Still photography mode .......................................................................................................... 32

Quality settings in Movie mode ........................................................................................................................... 32

BSTILL PHOTOGRAPHY

SSENSITIVITY .................................................................................................................................................................. 33

High-sensitivity photography (1600) ................................................................................................................... 34

JFinePix COLOR .............................................................................................................................................................. 35

FOCUSING (DISTANCE) ............................................................................................................................................... 36

EXPOSURE (SHUTTER SPEED AND APERTURE) ..................................................................................................... 37

TAKING PICTURES — SELECTING THE CAMERA SETTINGS .................................................................................. 38

■List of functions available in each mode .......................................................................................................... 39

■List of menu options available in each mode .................................................................................................. 39

AUTO ........................................................................................................................................................................... 40

SCENE POSITION ......................................................................................................................................................... 40

mPortrait ................................................................................................................................................................ 40

,Landscape .......................................................................................................................................................... 40

.Sports .................................................................................................................................................................. 40

/Night scene ......................................................................................................................................................... 40

PROGRAMMED AUTO .................................................................................................................................................. 41

SHUTTER-PRIORITY AUTO .......................................................................................................................................... 42

APERTURE-PRIORITY AUTO ....................................................................................................................................... 43

MANUAL ......................................................................................................................................................................... 44

dFLASH PHOTOGRAPHY ............................................................................................................................................... 45

xAuto flash mode .................................................................................................................................................. 46

bRed-eye reduction ............................................................................................................................................... 46

dForced flash ........................................................................................................................................................ 47

cSlow synchro ....................................................................................................................................................... 47

nRed-eye reduction + Slow synchro ..................................................................................................................... 47

Increasing the monitor brightness ................................................................................................................ 47

MANUAL FOCUS ........................................................................................................................................................... 48

CONTINUOUS AF .......................................................................................................................................................... 49

fCONTINUOUS SHOOTING ............................................................................................................................................ 50

fTop 10-frame continuous shooting ..................................................................................................................... 51

jAuto bracketing ................................................................................................................................................... 51

STILL PHOTOGRAPHY FUNCTIONS

PHOTO MODE STILL PHOTOGRAPHY

PHOTO MODE STILL PHOTOGRAPHY/MOVIE

3 Advanced Features

kFinal 10-frame continuous shooting .................................................................................................................... 51

hLong-period continuous shooting with 1280 ×960 -pixel mode .......................................................................... 52

DEXPOSURE COMPENSATION ...................................................................................................................................... 53

USING AE LOCK ............................................................................................................................................................ 54

eMACRO (CLOSE-UP) ..................................................................................................................................................... 55

PHOTOGRAPHY INFORMATION .................................................................................................................................. 56

qSTILL PHOTOGRAPHY MENU OPERATION (Important. Please read.) ....................................................................... 57

STILL PHOTOGRAPHY MENU ...................................................................................................................................... 58

*SELF-TIMER PHOTOGRAPHY ...................................................................................................................................... 58

AWHITE BALANCE ........................................................................................................................................................... 59

+AF MODE ........................................................................................................................................................................ 60

´MULTI ................................................................................................................................................................. 60

CENTER ............................................................................................................................................................. 61

˜AREA .................................................................................................................................................................. 61

‘PHOTOMETRY ............................................................................................................................................................... 62

jBRACKETING ................................................................................................................................................................. 62

GSHARPNESS .................................................................................................................................................................. 63

TMULTIPLE EXPOSURE ................................................................................................................................................. 63

zFLASH BRIGHTNESS ADJUSTMENT ........................................................................................................................... 64

∞USING AN EXTERNAL FLASH ...................................................................................................................................... 64

BMOVIE

rRECORDING MOVIES ................................................................................................................................................... 67

PLAYING BACK MOVIES ............................................................................................................................................... 69

BPLAYBACK

PLAYBACK INFORMATION ........................................................................................................................................... 70

oERASING SINGLE / ALL FRAMES ................................................................................................................................71

iPROTECTING IMAGES: FRAME / SET ALL / RESET ALL ........................................................................................... 73

gAUTO PLAY (AUTOMATIC PLAYBACK) ....................................................................................................................... 75

tRECORDING VOICE MEMOS ....................................................................................................................................... 76

tPLAYING BACK VOICE MEMOS ................................................................................................................................... 78

uHOW TO SPECIFY PRINT OPTIONS (DPOF) .............................................................................................................. 79

uDPOF SET FRAME ........................................................................................................................................................ 80

UDPOF ALL RESET .......................................................................................................................................................... 82

PHOTO MODE PLAYBACK

PLAYBACK MENU

PLAYBACK FUNCTIONS

PLAYBACK MODE

MOVIE MODE

STILL PHOTOGRAPHY MENU

6 7

h16 MB, xD-Picture Card™ (1)

Included with: Anti-static case (1)

hAA-size alkaline batteries (4)

hShoulder Strap (1)

hProtective cover (2)

hMetal strap clip (2)

hClip attaching tool (1)

hLens cap (1)

hLens cap holder (1)

hA/V (audio-visual) cable (1)

(plug (2.5 mm dia.) to pin-plug cable ××2)

hUSB cable (mini-B) (1)

hIEEE1394 4-pin to 6-pin cable (1)

hSync terminal cap (1)

(Attached to camera)

hCD-ROM (1)

Software for FinePix SX

hOwner’s Manual (this manual) (1)

Preface

■Test Shots Prior to Photography

For particularly important photographs (such as

weddings and overseas trips), always take a test

photograph and view the image to make sure that the

camera is functioning normally.

hFuji Photo Film Co., Ltd. cannot accept liability for

any incidental losses (such as the costs of

photography or the loss of income from

photography) incurred as a result of faults with this

product.

■Notes on Copyright

Images recorded using your digital camera system

cannot be used in ways that infringe copyright laws

without the consent of the owner, unless intended only

for personal use. Note that some restrictions apply to

the photographing of stage performances,

entertainments and exhibits, even when intended

purely for personal use. Users are also asked to note

that the transfer of memory cards (xD-Picture Card or

Microdrive) containing images or data protected under

restrictions imposed by those copyright laws.

■Liquid Crystal

If the LCD monitor is damaged, take particular care

with the liquid crystal in the monitor. If any of the

following situations arise, take the urgent action

indicated.

hIf liquid crystal comes in contact with your skin

Wipe the area with a cloth and then wash thoroughly

with soap and running water.

hIf liquid crystal gets into your eye

Flush the affected eye with clean water for at least

15 minutes and then seek medical assistance.

hIf liquid crystal is swallowed

Flush your mouth thoroughly with water. Drink large

quantities of water and induce vomiting. Then seek

medical assistance.

■Notes on Electrical Interference

If the camera is to be used in hospitals or aircrafts,

please note that this camera may cause interference

to other equipment in the hospital or aircraft. For

details, please check with the applicable regulations.

■Handling Your Digital Camera

This camera contains precision electronic

components. To ensure that images are recorded

correctly, do not subject the camera to impact or

shock while an image is being recorded.

■Trademark Information

hand xD-Picture Card™ are trademarks of

Fuji Photo Film Co., Ltd.

hIBM PC/AT is a registered trademark of International

Business Machines Corp. of the U.S.A.

hMacintosh, Power Macintosh, iMac, PowerBook, iBook

and Mac OS are trademarks of Apple Computer, Inc.,

registered in the U.S. and other countries.

hAdobe Acrobat®Reader®is a trademark of Adobe

Systems Incorporated of the U.S.

hMicrosoft, Windows, and the Windows logo are

trademarks, or registered trademarks of Microsoft

Corporation in the United States and/or other

countries. Windows is an abbreviated term referring

to the Microsoft®Windows®Operating System.

✽The “Designed for Microsoft®Windows®XP” logo

refers to the camera and the driver only.

hMicrodrive is a trademark of the International

Business Machines Corporation of the U.S.

hOther company or product names are trademarks or

registered trademarks of the respective companies.

■Explanation of Color Television System

NTSC: National Television System Committee, color

television telecasting specifications adopted

mainly in the U.S.A., Canada and Japan.

PAL: Phase Alternation by Line, a color television

system adopted mainly by European countries

and China.

■Exif Print (Exif ver. 2.2)

Exif Print Format is a newly revised digital camera file

format that contains a variety of shooting information

for optimal printing.

Accessories included

8 9

Camera parts and features ✽

Refer to the pages in parentheses for information on using the camera parts or feature.

Command dial (P.20)

Continuous

shooting button

(P.50)

Exposure

compensation

button (P.53)

Flash button

(P.45)

Release socket

(P.25)

Shutter button

Power

switch Playback mode (P.29)

Photography mode (P.23)

Power-OFF

Mode dial

Set-up

Movie (P.67)

Programmed Auto (P.41)Manual (P.44)

Set-up (P.83)Shutter-priority Auto (P.42) Scene Position (P.40)

Aperture-priority Auto (P.43) Auto (P.40)

Sync terminal (P.65)

Sync terminal cap

Hot shoe (P.64) FZ ring

(Focus/Zoom ring)

(P.21, 24, 48)

Self-timer lamp (P.58)

Still image shooting Movie recording

Strap mount (P.10)

Zoom button (P.19, 28)

AE-L (AE lock) button (P.21, 54)

BACK button (P.20)

Photo mode ( ) button (P.21)

DISP (display)

button

(P.21, 28)

Viewfinder (EVF)

Diopter adjustment

dial

(Focus check) button (P.21, 48)

Slot cover (P.14)

MENU/OK button (P.20)

4-direction (fg) button (P.20)

Battery cover

(P.12)

LCD monitor

Indicator lamp (P.26)

EVF/LCD

(viewfinder/

monitor) button

(P.19, 23)

Tripod mount

xD-Picture Card slot

(P.14)

Microdrive slot (P.14)

Microdrive eject button (P.15)

Flash pop-up button (P.19, 45)

(One-touch AF) button

(P.21, 48)

SHIFT button (P.22)

Speaker

Microphone

A/V OUT (Audio/Visual output)

socket (P.98)

IEEE1394 socket (P.100)

DC IN 5V (power input) socket (P.98)

Terminal cover

Focus mode selector switch (P.21, 48)

Terminal cover

INFO (information check) button (P.21, 56, 70)

Strap mount (P.10)

USB socket (mini-B)

(P.100)

Lens

Macro (close-up photography)

button (P.21, 55)

Flash control sensor

Flash (P.45)

External AF sensor

１／１／２００

４

３３

Ｆ

Ｐ

２０００

Ｆ２．８

１００−０００１

１／１／２００

４ １２：００ＡＭ

１２：００ＡＭ

ＩＳＯ８００

Self-Timer

Flash

Zoom bar

Date

Playback mode

Date

Still photography mode

Shutter speed

AE lock

Aperture setting display

Number of available frames

FinePix COLOR

Quality mode

Battery level warning

Media

AF warning

Camera shake warning

Media

Adapter mode

■Still photography mode

Playback frame number

Voice memo

DPOF

Protection

Time

■Playback mode

AF frame

Focusing indicator marks

Exposure compensation

Exposure compensation indicator

Macro

SensitivityContinuous shooting

Example of screen text display

10 11

Getting Ready

lens cap holder

Fastener

When attaching the strap to the camera, attach the metal strap clip to the camera before threading

the strap through the clip. This description explains how to attach the strap using the clip attaching

tool provided to make attaching the metal strap clip easier.

(Numbers 1to 8refer to the illustrations.)

Checking that the metal strap clip is facing the right

way, slide the clip fully into the clip attaching tool

and open up the gap in the strap clip.

Remove fasteners Aand Bfrom only one side of

the shoulder strap. Then pass the shoulder strap

through the lens cap holder and then back through

fasteners Aand B.

7Thread the strap through the protective cover and

metal strap clip.

8Thread the strap through the buckle and retainer.

Repeat steps 7to 8to attach the other end of the

strap.

●

Attach the lens cap cord to the camera to avoid losing the

lens cap.

1Attach the lens cap cord by threading it through

the metal strap clip near the terminal cover.

2Attach the lens cap by pressing in on each side

of the cap.

Gap

Clip attaching tool

Metal strap clip

●

Keep the clip attaching tool in a safe place as you will also

need it for removing the metal strap clip from the camera.

2Keeping the metal strap clip open, hook the open

metal strap clip through the strap mount on the

camera until it is secure.

31Once the clip is securely hooked through the

strap mount, hold the clip in place as you

remove the clip attaching tool.

2Turn the metal strap clip around once until it

clicks closed and is fully threaded onto the strap

mount.

Notch

Face the black side of the cover towards the

camera and attach the strap by threading the strap

through the strap clip, starting from the notched

side.

Repeat steps 1to 4to attach the other end of the

strap.

ATTACHING THE LENS CAP AND STRAP

1Getting Ready

◆Using the lens cap holder ◆

Make sure that the lens cap does not appear in your

shot when you take a picture, attach it to the lens cap

holder.

12 13

Getting Ready

1Check that the camera is turned off (indicator lamp

is off) before opening the battery cover.

●

Opening the battery cover while the camera is on, the camera

is turned off.

●

Do not apply force to the battery cover.

2Load the batteries correctly as indicated by the

polarity icons.

Pull on the battery cover to close it.

1While pressing on the battery cover to push the

batteries down, 2slide the cover closed.

LOADING THE BATTERIES

◆How to use the batteries ◆

Compatible batteries

hAA-size alkaline batteries (4) or AA-size Ni-MH rechageable batteries (4) (sold separately).

●

Please use the same brand and grade AA-size alkaline batteries as those supplied with the camera.

hNever use the following types of batteries, as this could cause serious

problems such as battery fluid leakage or overheating:

1. Batteries with split or peeling outer casings

2. Combinations of different types of batteries or new and used batteries

together

hDo not use manganese or Ni-Cd batteries.

hSoil, such as fingermarks on the poles of the batteries can shorten time for which the batteries can be

used.

hThe time for which AA-size alkaline batteries (referred to hereafter simply as alkaline batteries) can

be used varies depending on the brand, and some alkaline batteries may stop providing power more

quickly than those supplied with the camera. Note also that due to their nature, the time for which

alkaline batteries can be used decreases in cold conditions (0°C to +10°C/+32°F to +50°F). The use

of AA-size Ni-MH batteries is better for this reason.

hUse the optional charger to charge AA-size Ni-MH batteries.

hSee P.107-108 for other notes on using batteries.

hWhen first purchased or if left unused for a long period, the time for which AA-size Ni-MH batteries

can be used may be shorter. See P.108 for more information.

Outer casing

Do not open the battery cover while the camera is

on. This could damage the media or ruin the image

files on the media.

14 15

Getting Ready

●

Insert only the appropriate media types into the xD-Picture Card and Microdrive slots. Inserting the incorrect media

will damage the camera or media.

●

If the media is oriented incorrectly, it will not go all the way into the slot. Do not apply excessive force when inserting

an xD-Picture Card or Microdrive.

●

If the media is not fully inserted into the slot, the “å” message appears.

Gold marking

Align the gold marking on the xD-Picture

Card slot with the gold contact area on

the xD-Picture Card and push the card

firmly all the way into the slot.

Push the Microdrive firmly all the way into

the Microdrive slot.

xD-Picture Card Microdrive

3Close the slot cover.

Use either xD-Picture Card or Microdrive as recording media in the FinePix S20 Pro.

hIf an xD-Picture Card and a Microdrive are inserted at the same time, images will be recorded

onto the media selected as the “MEDIA” (➡P.83).

hData cannot be copied between the two media types on the FinePix S20 Pro.

1Set the Power switch to “OFF”, check that the

indicator lamp is off and then open the slot cover.

●

If opening the slot cover while the camera is still on, the

camera will turn off.

INSERTING THE MEDIA

Do not open the slot cover while the camera is still

turned on. This could damage the media or corrupt

the image files on the media.

◆How to replace

the xD-Picture Card ◆

Push the xD-Picture Card into the slot and

then slowly remove your finger. The lock is

released and the xD-Picture Card is pushed

out.

◆How to replace

the Microdrive ◆

Open the slot cover, press the Microdrive eject

button and remove the Microdrive.

●

When storing Microdrives, always use the special

protective case.

Microdrive eject button

●

The information above is a guide for photography mode. Depending on the camera mode and the type of batteries

used, the transition from “C” to “V” may occur more quickly.

●

When the batteries run out, “V” appears and camera operation stops. When this occurs, the camera may work if

you turn it on again even without loading new or fully charged batteries. However, this may cause camera faults such

as the camera turning itself off without retracting the lens. Always load new or fully charged batteries.

●

Due to the nature of the battery, the battery low warning may appear early when the camera is used in cold

locations. This is normal. Try warming the batteries in your pocket or a similar location before use.

“C” appears as a small icon on the right-hand

side of the screen. “V” appears as a large icon

on the screen.

ＡＵＴＯＡＵＴＯ

２５０２５０Ｆ５．６

３３３３

Turn the camera on and check that no battery level warning (“C” or “V”) appears on the

screen. If no icon appears, there is ample charge left in the batteries.

1There is ample battery charge.

2There is insufficient charge left in the batteries.

The batteries will soon run out. Have a new set

of batteries ready.

3The batteries are depleted. The display will

shortly go blank and the camera will stop

working. Replace or recharge the batteries.

Blinking red

Lit red

No icon

Blinking red

Lit red

◆Power save function ◆

When this function is active, it also turns off the screen (Sleep mode) to reduce power consumption if

the camera is not used for 30 seconds (➡P.86). If the camera is then left unused for 2 minutes or 5

minutes, the Power save function turns the camera off. To turn the camera back on, set the Power

switch to “OFF” briefly and then back to “q” or “w”.

CHECKING THE BATTERY CHARGE

１２：００ＡＭ１２：００ＡＭ

ＤＡＴＥＴＩＭＥＤＡＴＥＴＩＭＥ

ＳＥＴＳＥＴＣＡＮＣＥＬＣＡＮＣＥＬ

ＯＫＯＫ

BACKBACK

１０１０．．２．２００．２００４

ＤＤ

ＤＤＭＭＭＭＹＹＹＹＹＹＹＹ

．  ．

１２：００ＡＭ１２：００ＡＭ

ＳＥＴＳＥＴＣＡＮＣＥＬＣＡＮＣＥＬ

ＯＫＯＫ

BACKBACK

ＤＡＴＥＴＩＭＥＤＡＴＥＴＩＭＥ

２／／１０１０／２００／２００４

ＭＭＤＤＹＹＹＹ

ＭＤＤＹＹＹＹ

／／   ／

ＦＲＦＲＡＭＡＭＥＮＥＮＯ．Ｏ．

ＣＣＤ−ＲＣＣＤ−ＲＡＷ

ＣＯＮ

ＣＯＮＴ．Ｔ．

ＯＦＦＯＦＦ

ＡＤＡＰＴＥＲＡＤＡＰＴＥＲＮＯＮＯ

ＤＡＴＥＤＡＴＥ／ＴＩＭＥＴＩＭＥＳＥＴＳＥＴ

ＶＩＤＥＯＳＹＳＴＶＩＤＥＯＳＹＳＴＥＭＮＴＳＣ

ＮＴＳＣ

ENGLISHENGLISH

言語言語

／ＬＡＮＬＡＮＧ．Ｇ．

ＳＥＴ−ＵＰＳＥＴ−ＵＰ２／３２／３

１／１／２００１／１／２００４

１２：００ＡＭ１２：００ＡＭ

ＳＥＴＳＥＴＣＡＮＣＥＬＣＡＮＣＥＬ

ＯＫＯＫ

BACKBACK

ＤＡＴＥＴＩＭＥＤＡＴＥＴＩＭＥ

ＭＭＤＤＹＹＹＹＭＤＤＹＹＹＹ

／／   ／

16 17

Getting Ready

ＰＰＯＷＯＷＥＲＳＡＶＥＥＲＳＡＶＥ

ＦＯＦＯＲＭＲＭＡＴＡＴ

２ＭＩＮ２ＭＩＮ

ＭＥＤＩＡＭＥＤＩＡ

ＩＭＡＧＥＤＩＳＰ．ＡＧＥＤＩＳＰ．ＯＮＯＮ

ＯＫＯＫ

ＢＥＥＰＢＥＥＰ

ＳＨＵＴＴＥＲＳＨＵＴＴＥＲ

ＳＥＴ−ＵＰＳＥＴ−ＵＰ１／３１／３

1Set the Power switch to “q”.

2Set the Mode dial to “W”.

21Press “a” or “b” to select “DATE/TIME”.

2Press “c”.

0102

010203

ＳＥＴＳＥＴＮＯＮＯ

ＯＫＯＫ

BACKBACK

ＤＡＴＥＤＡＴＥＴＩＭＥＮＯＴＳＥＴＴＩＭＥＮＯＴＳＥＴ

２／／１０１０／２００／２００４

１２：００ＡＭ

ＤＡＴＥＴＩＭＥＤＡＴＥＴＩＭＥ

ＳＥＴＳＥＴＣＡＮＣＥＬＣＡＮＣＥＬ

ＯＫＯＫ

BACKBACK

ＭＭＤＤＹＹＹＹＭＭＤＤＹＹＹＹ

0102

TURNING ON AND OFF / SETTING THE DATE AND TIME

After purchasing the camera, first time when you

turn camera on, the date and time are cleared.

Press the “MENU/OK” button to set the date and

time.

1Press “d” or “c” to select Year, Month, Day,

Hour or Minute.

2Press “a” or “b” to correct the setting.

Once you have set the date and time, press the

“MENU/OK” button. Pressing the “MENU/OK”

button changes the camera to Photography or

Playback mode.

1To turn the camera on, set the Power switch to “q”

or “w”. When turning the camera on, the indicator

lamp lights green.

To turn the camera off, set the Power switch to

“OFF”.

The lens moves when the camera is in “q” mode.

Take care not to obstruct the lens as it is a

precision component.

Obstructing the lens will cause damage and the

“ß” or “∂” message will

appear. Take care also not to get fingerprints on

the camera lens as this will result in impaired image

quality in your shots.

●

If the message (see figure at left) does not appear, refer to

“Correcting the date and time” (➡P.17) and check and correct

the date and time settings.

●

The message is also shown when the camera battery has

been removed and the camera has been left in storage for a

long period of time.

●

To set the date and time later, press the “BACK” button.

●

If you do not set the date and time, this message will appear

each time you turn the camera on.

●

Holding down “a” or “b” changes the numbers continuously.

●

When the time displayed passes “12:00”, the AM/PM setting

changes.

●

At the time of purchase and after leaving the camera for a

long period with the batteries removed, settings such as the

date and time are cleared. Once the AC power adapter has

been connected or the batteries have been fitted for 2 hours

or more, the camera settings will be retained for roughly 24

hours even if both sources of camera power are removed.

CORRECTING THE DATE AND TIME / CHANGING THE DATE ORDER

Correcting the date and time

1Press “d” or “c” to select Year, Month, Day,

Hour or Minute.

2Press “a” or “b” to correct the setting.

3Always press the “MENU/OK” button after the

settings are completed.

●

Holding down “a” or “b” changes the numbers continuously.

●

When the time displayed passes “12:00”, the AM/PM setting

changes.

010203

Changing the date order

1Press “d” or “c” to select the date order.

2Press “a” or “b” to set the order. Refer to the

table below for details of the settings.

3Always press the “MENU/OK” button after the

settings are completed.

Date order Explanation

YYYY.MM.DD Displays the date in the “year. month. day”

format.

MM/DD/YYYY Displays the date in the “month / day / year”

format.

DD.MM.YYYY Displays the date in the “day. month. year”

format.

ＦＲＦＲＡＭＡＭＥＮＥＮＯ．Ｏ．

ＣＣＤ−ＲＣＣＤ−ＲＡＷ

ＣＯＮ

ＣＯＮＴ．Ｔ．

ＡＤＡＰＴＥＲＡＤＡＰＴＥＲ

ＤＡＴＥＤＡＴＥ／ＴＩＭＥＴＩＭＥＳＥＴＳＥＴ

ＮＯＮＯ

ＯＦＦＯＦＦ

ENGLISHENGLISH

ＮＴＳＣＮＴＳＣ

言語言語

／ＬＡＮ／ＬＡＮＧ．Ｇ．

ＶＩＤＥＯＳＹＳＴＶＩＤＥＯＳＹＳＴＥＭ

ＳＥＴ−ＵＰ

ＳＥＴ−ＵＰ２／３２／３

Using

the Camera

●Flash release

To use the flash, press the Flash pop-up button

to release the flash.

●Photography mode selector

Turn the Mode dial to change Photography

mode.

Still image shooting

Auto

Scene Position

Manual

Shutter-priority Auto

Program Auto

Aperture-priority Auto

Movie recording

Set-up

Movie

Set-up

●ON/OFF and Photography/Playback

mode selector switch

Use the Power switch to select the mode.

Photography: Press

“

”

to zoom in (telephoto).

Press

“

”

to zoom out (wide-angle).

Playback: Press

“

”

to enlarge the image.

Press

“

”

to revert to normal display.

●Using the Zoom

●Changing between the viewfinder

(EVF) and the monitor (LCD)

Pressing the “EVF/LCD” button toggles

between the viewfinder and the LCD monitor.

Use whichever mode is best suited to your

shot.

Set-up

Movie

Still photography

EVF

LCD

SELECTING THE LANGUAGE

1The “SET-UP” screen appears. Press “a” or “b”

to select “ ”.

2Press “c” to select “ENGLISH”, “FRANCAIS”,

“DEUTSCH”, “ESPAÑOL”, “ ” or “ ”.

Press “c” to cycle through the language

settings.

●

The screens in this manual are shown in English.

●

See P.83 for more information on the “W” SET-UP menu.

20102

BASIC OPERATION GUIDE

2Using

the Camera

11Set Power switch to “q”.

2Set the Mode dial to “W” to display the SET-UP

menu.

0102

ＰＰＯＷＯＷＥＲＳＡＶＥＥＲＳＡＶＥ

ＦＯＦＯＲＭＲＭＡＴＡＴ

２ＭＩＮ２ＭＩＮ

ＭＥＤＩＡＭＥＤＩＡ

ＩＭＡＧＥＤＩＳＰ．ＡＧＥＤＩＳＰ．ＯＮＯＮ

ＯＫＯＫ

ＢＥＥＰＢＥＥＰ

ＳＨＵＴＴＥＲＳＨＵＴＴＥＲ

ＳＥＴ−ＵＰＳＥＴ−ＵＰ１／３１／３

0FinePix Photo mode ( ) button

Photography: Allows you to select the quality

(Number of recorded pixels),

sensitivity and FinePix COLOR

settings.

Playback: Allows you to specify the print order

(DPOF) settings.

0Diopter adjustment dial

Makes the image in the viewfinder easier

to see. Set the dial to the position where

the AF frame appears sharpest.

0AE-L button

The exposure remains locked while this

button is pressed.

0Focus check button

Pressing this button enlarges the central portion

of the screen. Use this to focus the image precisely.

Text displayed

Framing guideline displayed

No text displayed

Text displayed

No text displayed

Multi-frame playback

0DISP button Changes the screen display.

Photography

mode

Playback

mode

0FZ ring

Adjusts the focus. When the Focusing mode

is set to S-AF or C-AF, the focusing ring

can be used instead of the Zoom button.

0INFO button

Press this button to view image information.

Photography mode: Shows the current settings

(sensitivity, sharpness, etc.).

Playback mode: Displays the information for the image

currently displayed.

0One-touch AF button

Uses the AF function to focus the image once.

This can only be used for manual focusing.

0Focus mode selcector switch

Switches between C-AF (Continuous AF), S-AF

(Single AF) and MF (Manual focus).

0Macro button

Use this for close-up photography. Pressing this button changes the modes as follows:

Macro Super Macro Macro off (Normal)

Focal range: Macro 10 cm-80 cm (3.9 in.-2.6 ft.)

Super macro 1 cm-20 cm (0.4 in.-7.9 in.)

Normal 50 cm (1.6 ft.) to infinity (wide-angle), 90 cm (3.0 ft.) to infinity

(telephoto)

0SHIFT button

Can be used in combination

with other buttons to change

settings (➡P.22).

20 21

Using

the Camera

BASIC OPERATION GUIDE

Up, down, left and right are indicated

by black triangles in the Owner’s

Manual. Up or down is shown as

“a”or “b”, and left or right is shown

as “d”or “c”.

: Exposure compensation

Hold down the “”button and turn the

Command dial to select the setting.

: Flash

Release the pop-up flash, hold down the “ ”

button and turn the Command dial to select

the setting.

: Continuous shooting

Hold down the “”button and turn the

Command dial to select the setting.

0Command dial

In Photography mode, turn the Command dial to

select program shift and specify settings such as

the shutter speed and aperture.

0Using the menus

2Select a menu option.

Press the left or right arrow on

the 4-direction button.

3Select a setting.

Press the up or down arrow

on the 4-direction button.

1Display the menu.

Press the “MENU/OK”button.

4Confirm the setting.

Press the “MENU/OK”

button.

0BACK button

Press this button

when you want to

cancel a procedure

mid-way.

ＩＳＯＩＳＯ ２００２００

Ｐ

２５０２５０Ｆ５．６

３３３３

２５０２５０Ｆ５．６

３３３３

ＡＵＴＯＡＵＴＯ

ＯＦＦＯＦＦ

ＡＵＴＯＡＵＴＯ

２５０２５０Ｆ５．６Ｆ５．６

３３３３

ＯＦＦＯＦＦＡＵＴＯＡＵＴＯ

±１／３１／３

ＡＦＡＦＭＯＤＥＯＤＥ

ＣＥＮＴＥＲＣＥＮＴＥＲ

ＡＲＥＡＡＲＥＡ

ＭＵＬＴＩＵＬＴＩ

ＯＦＦＯＦＦＡＵＴＯＡＵＴＯ

±１／３±１／３

ＡＦＡＦＭＯＤＥＯＤＥ

ＣＥＮＴＥＲＣＥＮＴＥＲ

ＡＲＥＡＡＲＥＡ

ＭＵＬＴＩＵＬＴＩ

22 23

Using

the Camera

1Set the Power switch to “q”.

2Set the Mode dial to “B”.

3Set the Focus mode selector switch to “S-AF”.

hFocal range

Wide-angle: Approx. 50 cm (1.6 ft.) to infinity

Telephoto: Approx. 90 cm (3.0 ft.) to infinity

Press the Flash pop-up button to pop up the flash.

●

When the flash is popped up, the image may disappear and

the screen may go dark briefly due to flash charging. At the

same time, the indicator lamp blinks orange.

●

When using the flash in dusty conditions or when it is

snowing, white dots may appear in the image. The flash will

reflect off the dust particles or snowflakes. Try taking the shot

using Suppressed flash mode.

3Each time you press the “EVF/LCD” button, the

display switches between the viewfinder (EVF) and

the monitor (LCD). If the AF frame in the viewfinder

(EVF) is difficult to see, adjust the viewfinder using

the Diopter adjustment dial.

LCD

EVF

Diopter adjustment dial

BASIC OPERATION GUIDE TAKING PICTURES (AUTO MODE)

STILL PHOTOGRAPHY MODE

●

For close-up shots, use the Macro setting (➡P.55).

●

When the “å”, “©”,

“∆” or “˙” message appears, see P.111.

Continued

LCD monitor brightness / Volume adjustment

Holding down the “SHIFT”button and pressing

the “DISP”button displays the menu.Press “a”

or “b”to select an option and press “d”or

“c”to change the setting. Then press the

“MENU/OK”button to confirm the setting.

Note that the volume can only be adjusted in

Playback mode.

Self-timer

Hold down the “SHIFT”button and press the

“AE-L”button to change between 2 sec., 10

sec. and OFF as the self-timer setting.

Photometry / White balance

Holding down the “SHIFT”button and pressing

a button changes the setting on the Command

dial. Release the button to confirm the setting.

Refer to the page listed in the table below for

details of the respective settings.

Self-timer

Photometry

White balance

P. 5 8

P. 6 2

P. 5 9

Hold down the “SHIFT”button

for 1 second or longer

0SHIFT button

Holding down the “SHIFT”button for 1 second or longer displays the “SHIFT CONTROL”guide.

By pressing one of the displayed button combinations, you can quickly and easily access the corresponding

setting.

The functions you can access vary depending on the current mode. The example below shows the

procedure for Photography mode.

ＥＶＦＥＶＦ／ＬＣＤＬＣＤ

ＳＥＬＳＥＬＦ-ＴＩＭＥＲＥＲ

ＷＢ

ＰＨＯＴ

ＯＴＯＭＯＭＥＴＲＹＥＴＲＹ

ＳＨＩＦＴＣＯＮＴＲＯＬＳＨＩＦＴＣＯＮＴＲＯＬ

＋

ＳＨＩＦＴＳＨＩＦＴ

ＤＩＳＰＤＩＳＰ

ＡＥ−ＬＡＥ−Ｌ

ＰＰ

２５０２５０Ｆ５．６

３３３３

ＩＳＯＩＳＯ ２００２００

ＰＰ

２５０２５０Ｆ５．６

３３３３

ＩＳＯＩＳＯ ２００２００

ＡＵＴＯＡＵＴＯ

ＩＳＯＩＳＯ ２００２００

２５０２５０Ｆ５．６

３３３３

Ｐ

ＢＲＩＧＨＴＮＥＳＳＢＲＩＧＨＴＮＥＳＳ

＋−

ＳＥＴＳＥＴＣＡＮＣＥＬＣＡＮＣＥＬ

ＯＫＯＫ

BACKBACK

OFF

（No icon）

The EVF/LCD selection is retained even when the

camera is turned off or the Mode dial setting is

changed.

24 25

Using

the Camera

TAKING PICTURES (AUTO MODE)

STILL PHOTOGRAPHY MODE

4Brace your elbows against your sides and hold the

camera with both hands. Position the thumb of your

right hand so that it is handy for using the zoom.

●

The image will be blurred if the camera moves when taking

the picture (camera shake). Use a tripod to avoid camera

shake, particularly for shots in dark locations when the flash

is set to Suppressed flash mode.

●

There may be some uneven brightness at the lower edge of

the LCD monitor. This is normal and does not affect the

image.

Take care to hold the camera so that your fingers

or the strap do not cover the lens, flash or flash

control sensor. If the lens, flash or flash control

sensor is blocked by your fingers or the camera

strap, you may not get the correct brightness

(exposure) for your shot.

●

Check that the lens is clean. If it is dirty, clean the lens as

informed on P.107.

◆Using the FZ ring to adjust the zoom ◆

When the Focusing mode is set to S-AF or C-AF, the

FZ ring can be used instead of the Zoom button to

change the zoom setting.

Turn the FZ ring clockwise to zoom in and

counterclockwise to zoom out. A “zoom bar” appears

on the screen during zooming.

telephotowide-

angle

FZ ring

To zoom in on your subject, press “T” (telephoto)

button. To widen the angle of your shot, press “W”

(wide-angle) button. At that same time, the “zoom

bar” appears on the screen.

hOptical zoom focal length (35 mm camera

equivalent)

Approx. 35 mm-210 mm

Max. zoom scale: 6×

ＡＵＴＯＡＵＴＯ

２５０２５０Ｆ５．６

３３３３

Zoom bar

●

Zooming pauses briefly when it changes between optical

zoom and digital zoom (➡P.28). Press the same Zoom button

again to change Zoom modes.

Press the Shutter button down halfway. When a

short double-beep is heard, the camera focuses on

your subject. At that point, the AF frame on the

screen becomes smaller and the camera sets the

shutter speed and aperture (the indicator lamp

(green) stops blinking and remains lit).

●

The image shown on the screen before taking the picture

may differ in its brightness, color, etc. from the image actually

recorded. Playback the recorded image to check it (➡P.29).

●

If the camera does not emit a short double-beep and “{”

appears on the screen, the camera cannot focus.

●

Pressing the Shutter button down halfway, the image on the

screen freezes temporarily. However, this image is not the

recorded image.

●

If “{” appears on the screen (e.g. the shot is too dark for

the camera to focus), try standing about 2 m (6.6 ft.) from the

subject to take the picture.

8Bebeep

２５０２５０Ｆ５．６

Click

Press the Shutter button down fully without

releasing it. When a clicking noise is heard, the

camera records the image.

●

There is a slight delay between the Shutter button being

pressed and the picture being taken. Playback the shot to

check the image.

●

When pressing the Shutter button down fully in one motion,

the picture is taken without the AF frame changing.

●

Taking the picture, the indicator lamp lights orange (shooting

disabled). The indicator lamp then changes to green to

indicate that the next picture can be taken.

●

The indicator lamp blinks orange while the flash is charging.

The monitor may go dark briefly. This is normal.

●

See P.111-112 for information on the warning displays.

Frame the shot so that the subject fills the entire AF

(Auto Focus) frame.

●

If the subject is not in the AF frame, use AF/AE lock to take

the picture (➡P.27).

ＡＵＴＯＡＵＴＯ

３３３３

◆Support for a cable release ◆

●

Do not apply excessive force to a cable release that is

attached to the camera, as this could damage the camera.

A mechanical cable release can be used with this

camera.

Camera shake can be prevented by using a tripod

(sold separately) and cable release (sold separately).

Compatible cable releases:

ISO 6053:1979-compliant cable releases

Release socket

AF frame

26 27

Using

the Camera

Click

In a shot like the image on the left, the subjects are

not in the AF frame. If the picture is taken at this

point, the subjects will not be in focus.

USING AF/AE LOCKINDICATOR LAMP DISPLAY

３３３３

ＡＵＴＯＡＵＴＯ

Move the camera slightly so that one of the

subjects is in the AF frame.

Press the Shutter button down halfway. When a

short double-beep is heard, the camera focuses on

your subject. At that point, the AF frame on the

screen becomes smaller and the camera sets the

shutter speed and aperture. (The indicator lamp

(green) changes from blinking to lit.)

３３３３

ＡＵＴＯＡＵＴＯ

Bebeep

２５０２５０Ｆ５．６

Continue to hold the Shutter button down halfway

(AF/AE lock). Move the camera back to the original

image and then fully press down on the Shutter

button.

●

You can reapply the AF/AE lock as many times as you like

before releasing the shutter.

●

The AF/AE lock operates in all Photography modes and can

be used to ensure excellent results.

２５０２５０Ｆ５．６

◆AF/AE lock ◆

On the FinePix S20 Pro, when you press the Shutter button down half way, the focus and exposure

settings are locked (AF/AE lock). If you want to focus on a subject that is off to one side of the image or

set the exposure before you compose the final shot, lock the AF and AE settings then compose and

take your picture.

hWhen you cannot focus and AF/AE lock does not give the correct exposure

Position the AF frame over the main subject and apply the AE lock (➡P.54). Then position the AF

frame over another subject at roughly the same distance, press the Shutter button down halfway,

recompose the shot and then take the picture.

TAKING PICTURES (AUTO MODE)

STILL PHOTOGRAPHY MODE

NUMBER OF AVAILABLE FRAMES

ＡＵＴＯＡＵＴＯ

２５０２５０Ｆ５．６

３３３３

The number of available frames appears on the

screen.

●

See P.32 for information on changing the quality setting.

●

The default quality “y” set at shipment is 1.

■Standard number of frames per media

This is the standard number shown for a new media formatted on the camera. The larger the capacity of the media, the

greater the difference between the standard number and the actual number of frames displayed.

Also, because the amount of data recorded varies depending on the subject, the number of frames may not decrease or may

decrease by 2 when a frame is taken. Consequently, the actual number of frames may be more or less than what is

displayed.

◆Subjects not suitable for autofocus ◆

Though the FinePix S20 Pro uses an autofocus mechanism, it may have trouble focusing with the

following subjects and situations:

hVery shiny subjects such as a mirror or car

body

hSubjects photographed through glass

hSubjects that do not reflect well, such as hair

or fur

hSubjects with no substance, such as smoke or

flames

hWhen the subject is dark

hSubjects moving at high speed

hWhen there is very little contrast between the

subject and the background (such as white

walls or subjects dressed in the same color as

the background)

hWhen there is a high-contrast subject other

than the main subject at or near the center of

the image and that subject is closer to or

further from the camera than the main subject

(as when taking a picture of someone against

a background with contrasting colors)

For subjects of this type, use AF/AE lock (➡P.27).

Display Status

Lit green Ready to shoot.

Blinking green AF/AE in progress, camera shake warning or AF warning (Ready to shoot).

Blinking green and

orange alternately

Recording to media (Ready to shoot).

Lit orange Recording to media (Not ready).

Blinking orange Charging the flash (flash will not fire).

Flashing green

(1-second intervals)

Camera in Power save mode (➡P.86).

Blinking red iMedia Warnings

No card inserted, card not formatted, incorrect format, card full, media error.

iLens operation error.

✽Detailed warning messages appear on the screen (➡P.111-112).

Quality 5F5N

Number of recorded pixels

2832 ×2128

DPC-16 (16 MB) 5

171

2048 ×1536

162

325

1600 ×1200

101

204

409

1280 ×960

137

275

550

2832 ×2128

DPC-32 (32 MB)

DPC-64 (64 MB)

DPC-128 (128 MB)

DPC-256 (256 MB)

172 343 651 818 1101 39DPC-512 (512 MB)

117 234 445 559 752 26Microdrive 340 MB

353 698 1313 1642 2190 80Microdrive 1 GB

１００−０００１１００−０００１

２／１０１０／２００／２００４１２：５６ＰＭ１２：５６ＰＭ

28 29

Using

the Camera

VIEWING THE IMAGES (PLAYBACK)

PLAYBACK MODE

Single-frame playback

1Set the Power switch to “w”.

2Press “c” to scan forward through the images

and “d” to scan backwards.

●

Setting the Power switch to “w”, the last image is played back.

●

If the lens is extended during playback, the lens retracts as a

protective measure if the camera is not used for 6 seconds.

Fast-forwarding through the images

To scan quickly through the images by holding

down “d” or “c” for 1 second during playback.

Multi-frame playback

In Playback mode, the display shown on the screen

changes each time you press the “DISP” button.

Press the “DISP” button until the multi-frame

playback screen (9 frames) appears.

1Press “a”, “b”, “d” or “c” to move the cursor

(orange frame) to the frame you want to select.

Pressing “a” or “b” repeatedly changes to the

next page.

2Press the “DISP” button again to make the current

image bigger.

●

A bar is displayed to the location of the current image on the

media.

１００−００１５１００−００１５

Text displayed

No text displayed

Multi-frame playback

◆Still Images that can be viewed on the FinePix S20 Pro ◆

You can use this camera to play back still images recorded on a FinePix S20 Pro and still images

(excluding some uncompressed images) that were recorded on a FUJIFILM digital camera that

supports xD-Picture cards or Microdrives.

0102

Playback frame number

TAKING PICTURES (AUTO MODE)

STILL PHOTOGRAPHY MODE

USING THE ZOOM (OPTICAL ZOOM / DIGITAL ZOOM)

Press the Zoom buttons to zoom in and out.

The FZ ring can also be used to control the zoom

(➡P.24).

The digital zoom can be used with the “3”, “2”

and “1” quality settings.

When zooming changes between optical and digital,

the position of the “■” indicator stops. Pressing the

same Zoom button again starts the “■” indicator

moving again.

●

The digital zoom cannot be used with the “5” quality setting.

●

See P.32 for information on changing the quality setting.

●

If the shot goes out of focus during zooming, hold the Shutter

button down halfway to refocus the shot.

BEST FRAMING

Select the framing guide in the Still photography

mode. The screen display changes each time you

press the “DISP” button. Press the “DISP” button

until “Framing Guideline” appears.

Optical zoom

Digital zoom

Zoom bar display

ＴＷ

The position of the “”indicator on

the zoom bar shows the zooming status.

The area to the right of the separator

indicates digital zooming, while the area

to the left indicates optical zooming.

hOptical zoom focal lengths✽

Approx. 35 mm-210 mm, max. zoom scale: 6×

hDigital zoom focal lengths✽

3: Approx. 210 mm-290 mm,

max. zoom scale: Approx. 1.4×

2: Approx. 210 mm-372 mm,

max. zoom scale: 1.77×

1: Approx. 210 mm-465 mm,

max. zoom scale: Approx. 2.2×

✽35 mm camera equivalents

Text displayed

Framing guideline displayed

No text displayed

Scene

ＡＵＴＯＡＵＴＯ

３３３３

Use this frame with the main subject positioned at the intersection

of two lines or align one of the horizontal lines with the horizon.

This frame allows you to compose your own shots while

remaining aware of the subject's size and the balance of the shot.

●

The framing guideline is not recorded on the image.

●

The lines in the scene frame divide the recorded pixels into 3 roughly equal

parts horizontally and vertically. When the image is printed, the resulting

print may be shifted slightly from the scene frame.

telephotowide-

angle

FZ ring

◆Important ◆

Always use AF/AE lock when composing a shot.

The image may not be focused correctly if you do

not use AE/AF lock.

Zoom button

FZ ring

ＥＲＡＳＥＯＫ？ＥＲＡＳＥＯＫ？

ＹＥＳＹＥＳＣＡＮＣＥＬＣＡＮＣＥＬ

ＯＫＯＫ

BACKBACK

ＦＲＦＲＡＭＡＭＥ

１００−０００９１００−０００９

ＢＡＣＫＢＡＣＫ

ＥＲＡＳＥＥＲＡＳＥ

ＦＲＦＲＡＭＥ

ＡＬＬＦＲ

ＡＬＬＦＲＡＭＡＭＥＳＥＳ

ＢＡＣＫＢＡＣＫ

ＥＲＡＳＥＥＲＡＳＥ

ＦＲＦＲＡＭＡＭＥ

ＡＬＬＦＲ

ＡＬＬＦＲＡＭＡＭＥＳＥＳ

30 31

Using

the Camera

ERASING IMAGES (ERASE FRAME)

PLAYBACK MODE

1Set the Power switch to “w”.

1Press the “MENU/OK” button during playback to

display the menu.

2Press “d” or “c” to select “o” ERASE.

1Press “a” or “b” to select “FRAME”.

2Press the “MENU/OK” button to confirm the

selection.

See P.71 for information on “ALL FRAMES”.

41Press “d” or “c” to select a frame (file) to be

erased.

2Press the “MENU/OK” button to erase a displayed

frame (file).

To erase another frame (file), repeat steps 1and 2.

0102

VIEWING THE IMAGES (PLAYBACK)

PLAYBACK MODE

Playback zoom

Pressing the Zoom button during single-frame

playback zooms (enlarges) the still image. At

that point, a zoom bar appears.

hZoom scales

5F, N 2832 ×2128 pixel images: Max. 18×

32048 ×1536 pixel images: Max. 13×

21600 ×1200 pixel images: Max. 10×

11280 ×960 pixel images: Max. 8×

●

Do not use multi-frame playback during playback

zoom.

Panning

Pressing “a”, “b”, “d” or “c” to display

another part of the image.

Trimming

Check the size of the saved image and press the

“MENU/OK” button. The cropped image is added

as a separate file in the final frame.

Press the “MENU/OK” button

to crop the image.

Single-frame playback

Press the “BACK” button to

cancel playback zoom.

1M1M

ＲＥＣＯＫ？ＲＥＣＯＫ？

ＲＥＣＲＥＣＣＡＮＣＥＬＣＡＮＣＥＬ

ＯＫＯＫ

ＢＡＣＫＢＡＣＫ

ＴＲＩＴＲＩＭＭＩＮＧＭＩＮＧ

Zoom bar

The size of the saved image varies depending on

the zoom scale. If the saved image size is less

than “1”, “ΩTRIMMING” disappears and

cannot be saved the image trimmed. For CCD-

RAW files, “ΩTRIMMING” is not displayed

and trimmed images cannot be saved.

■Image Sizes

3Best for A5 to A4 size prints

2Best for A6 to A5 size prints

1Best for A6 size prints

ＴＲＩＴＲＩＭＭＩＮＧＭＩＮＧ

ＯＫＯＫ

Zoom bar

ＴＲＩＴＲＩＭＭＩＮＧＭＩＮＧ

ＯＫＯＫ

●

Pressing the “MENU/OK” button repeatedly erases

consecutive frame (files). Take care not to erase a frame

(files) by mistake.

●

Press “a” or “b” to select “ BACK” and press “MENU/OK”

button to return to single-frame playback.

●

Press the “BACK” button to cancel erasing single frame.

Note that erased images cannot be recovered.

Please copy important frames (files) to avoid

loosing them to your computer or another media.

32 33

Advanced

Features

11Set the Power switch to “q”.

2Set the Mode dial to Still photography mode.

3Press the Photo mode (p) button.

●

In “r” Movie mode, do not set the “S” (sensitivity) setting.

11Set the Power switch to “q”.

2Set the Mode dial to Still photography mode or

Movie mode.

3Press the Photo mode (p) button.

21Press “d” or “c” to select the “y” quality setting

and then press “a” or “b” to change the setting.

2Press the “MENU/OK” button to confirm the

setting.

Choose from 5 settings. Using the table below as a

guide, select the setting that best suits the aims.

●

The numbers to the right of each setting show the number of

available frames.

●

When changing the quality setting, the number of available

frames also changes (➡P.26).

Quality settings in Still photography mode

ＡＵＴＯＡＵＴＯ

ＱＱＵＡＬＩＴＹＵＡＬＩＴＹ

１９１９

３３ＦＲ３３ＦＲＡＭＡＭＥＳＥＳ

１０１０

２５２５

ＳＴＤＳＴＤ

Ｎ

The movie sizes are “%” and “$”.

hMovie size

%640 ×480 pixels (for better quality)

$320 ×240 pixels (to record longer movies)

hFrame rate

30 frames per second (fixed)

See P.117 for information on the frame rate.

Quality settings in Movie mode

ＱＵＱＵＡＬＩＴＹＡＬＩＴＹ

６４０ｘ４８０６４０ｘ４８０

３２３２０ｘ０ｘ２４２４０

0102

QUALITY MODE (NUMBER OF RECORDED PIXELS)

pPHOTO MODE STILL PHOTOGRAPHY/MOVIE

3Advanced

Features

Quality mode

Printing at A4 size or printing part of the image cropped at A5 or A6 size.

5N (2832 ×2128)

Printing at A4 size or printing part of the image cropped at A5 or A6 size.

For better image quality, select “5F”.

5F (2832 ×2128)

Printing at A4 or A5 size or printing part of the image cropped at A6 size.

3(2048 × 1536)

Printing at A5 or A6 size.

2(1600 × 1200)

Printing at A6 size.

1(1280 × 960)

Sample Uses

The quality setting is retained even when the

camera is turned off or the Mode dial is changed.

Sensitivity is retained even when the camera is

turned off or the Mode dial is changed.

SSENSITIVITY

pPHOTO MODE STILL PHOTOGRAPHY

ＡＵＴＯＡＵＴＯ

ＩＳＯＩＳＯ

ＳＴＤＳＴＤ

４００４００

ＡＵＴＯＡＵＴＯ

８００８００

１６００１６００

21Press “d” or “c” to select the “S” setting and

then press “a” or “b” to change the setting.

2Press the “MENU/OK” button to confirm the

setting.

hSettings

B: AUTO (160 to 800) / 400 / 800 / 1600

?, N, M, <and >: 200 / 400 / 800 / 1600

●

When setting CCD-RAW (➡P.88), only the “200” and “400”

sensitivity settings can be selected.

●

While selecting a higher sensitivity setting will allow you to

take pictures in darker locations, it will also increase the

amount of speckling in your images. Streaking may also be

visible in shots of scenes such as the night sky.

Choose the sensitivity setting that best suits the conditions.

0102

２００２００

ＩＳＯＩＳＯ

ＳＴＤＳＴＤ

４００４００

２００２００

８００８００

１６００１６００

////

ＰＰ

３３３３

２５０２５０Ｆ５．６Ｆ５．６

ＩＳＯＩＳＯ ４００４００

Selecting AUTO as the sensitivity setting, the

camera selects the best sensitivity setting for the

subject brightness.

The AUTO sensitivity setting can be selected in the

“B” Photography modes.

3When the sensitivity is set to “200”, “400”, “800” or

“1600” the selected sensitivity setting appears on

the screen.

34 35

Advanced

Features

JFinePix COLOR

pPHOTO MODE STILL PHOTOGRAPHY

SSENSITIVITY

pPHOTO MODE STILL PHOTOGRAPHY

◆Quality setting in High-sensitivity mode ◆

If you try to select a quality setting (➡P.32) other than “1” when the camera is set to High-sensitivity

mode, “&” appears blinking and the quality cannot be changed.

ＳＴＤＳＴＤ

ＡＵＴＯＡＵＴＯ

ＳＴＡＮＤＡＲＤＳＴＡＮＤＡＲＤ

ＣＨＲＣＨＲＯＭＯＭＥ

Ｂ＆

Ｂ＆Ｗ

ＣＯＬＯＲＣＯＬＯＲ

●

In “r” Movie mode, do not set the “J” FinePix COLOR

setting.

11Set the Power switch to “q”.

2Set the Mode dial to Still photography mode.

3Press the Photo mode (p) button.

21Press “d” or “c” to select the “J” FinePix

COLOR setting and then press “a” or “b” to

change the setting.

2Press the “MENU/OK” button to confirm the

setting.

0102

The FinePix COLOR setting is retained even when

the camera is off or the Mode dial is changed.

●

p-CHROME may have little visible effect with some subjects,

such as close-up shots of people (portraits).

●

Because the effects on the image differ depending on the

scene being shot in p-CHROME mode, take pictures in

standard mode as well as this mode. Note that you may not

be able to see any difference on the screen.

●

For shots taken in p-CHROME mode or p-B&W mode,

automatic quality adjustment will be suppressed on Exif Print

compliant printers.

When setting p-CHROME or p-B&W, the icon

appears on the screen.

p-CHROME:

p-B&W:

The contrast and color saturation are set to standard. Use this mode for normal

photography.

p-STANDARD (STD)

The contrast and color saturation are set to high. This feature is effective for taking more

vivid shots of subjects such as scenery (blue sky and greenery) and flowers.

p-CHROME (CHR)

This setting converts the colors in the photographed image to black and white.

p-B&W (B&W)

ＰＰ

３３３３

２５０２５０Ｆ５．６Ｆ５．６

ＩＳＯＩＳＯ ４００４００

High-sensitivity photography (1600)

When a high-sensitivity (1600) is selected, the

quality is set to “1” (the “®” appears).

●

The digital zoom cannot be used in high-sensitivity photography.

●

The high-sensitivity photography cannot be selected when

setting CCD-RAW (➡P.88).

●

When you specify a high sensitivity, the amount of noise

(interference) in the image shown on the screen before the

picture is taken increases. However, this is normal.

ＱＵＡＬＩＴＹＱＵＡＬＩＴＹ

Ｐ

３３３３

２５０２５０Ｆ５．６Ｆ５．６

ＩＳＯＩＳＯ１６００１６００

High-sensitivity photography is retained even when

the camera is off or the Mode dial is changed.

36 37

Advanced

Features

EXPOSURE (SHUTTER SPEED AND APERTURE)

STILL PHOTOGRAPHY FUNCTIONS

Closed Open

When shooting a moving subject, you can either “freeze the motion” or “capture the sense of

movement” by adjusting the shutter speed.

Freezes the motion of the

subject.

Photographs the traces left

by the subject's movement.

By adjusting the aperture, you can change the depth of focus (depth of field).

The area in front of and

behind the subject is also

in focus in the shot.

The background is out of

focus.

Fast Slow

Shutter speed

Aperture

FOCUSING (DISTANCE)

STILL PHOTOGRAPHY FUNCTIONS

Exposure refers to the light that hits the CCD or the total amount of captured light and determines

the brightness of the image.

The exposure is determined by the combination of aperture and shutter speed. In AE (automatic

exposure), the camera determines the correct exposure, allowing for factors such as the brightness

of the subject and the sensitivity setting.

The graph at left shows the way the aperture and shutter speed settings can

be changed while maintaining the same exposure level.

hWhen the aperture is decreased by one step, the shutter speed also

decreases by one step (the dot moves upper left).

hWhen the aperture is increased by one step, the shutter speed also

increases by one step (the dot moves lower right).

hCombinations that result in the shutter speed or aperture being outside the

available range of settings cannot be selected (white dots).

hIn the “N”, “M” and “<” photography modes, it is easy to select different

settings along this line.

hSelecting settings that run parallel to this line by adjusting the brightness of

the photographed image is referred to as exposure compensation.

OpenClosed (Aperture)

Slow (Shutter speed) Fast

◆When you cannot get the correct exposure ◆

AE lock: Determines and fixes the exposure at a target level. Use the following procedure to take a

picture using AE lock:

Press the “AE-L” button (sets and locks the

exposure). ➡Press the Shutter button down

halfway (sets and fixes the focus). ➡Press

the Shutter button down fully (takes the

picture).

Exposure compensation:

This function uses the exposure level set by

the AE function as a reference (0) and then brightens (+) or darkens (–) the image. By

selecting Auto bracketing, you can shoot 3 frames, one underexposed (–), one at the

reference exposure (0) and one overexposed (+).

(–) (0) (+)

Main subject

The distance from the subject to the camera is referred to as the shooting distance.

When the shooting distance is set correctly and the image appears sharp, the image is focused.

■Three focusing methods

There are mechanisms for focusing: (1) Single AF (S-AF); (2) Continuous AF (C-AF); and (3)

Manual focus (MF).

S-AF: Use S-AF for normal photography. In this mode, the camera focuses each time the Shutter

button is pressed down halfway.

✽2 Turning Macro mode ON/OFF

Wide angle:

50 cm (1.6 ft.) to infinity

Telephoto:

90 cm (3.0 ft.) to infinity

10 cm-80 cm

(3.9 in.-2.6 ft.)

1 cm-20 cm

(0.4 in.-7.9 in.)

Macro OFF Macro ON Super Macro ON

C-AF: Use C-AF when photographing moving subjects. When this mode is set, the camera

focuses continuously on the subject in the center of the screen. See P.49 for details.

MF: The focus is adjusted by turning the focusing ring manually. See P.48 for details.

◆The AF sensor ◆

The FinePix S20 Pro uses an external AF sensor (external-light passive phase difference AF)

that features faster AF operation than previous models. The external AF sensor does not

function when Macro mode, Super macro mode, the digital zoom, AREA or C-AF focusing is

used or when “ADAPTER-YES” is selected. It may take longer to focus if the external AF sensor

is soiled (➡P.113).

■Causes of focusing errors and the solutions

The subject is not suited to AF. Use AF lock (Focus mode: AF (CENTER))✽1 or MF.

The subject is not in the AF frame. Use AF lock (Focus mode: AF (CENTER))✽1 or MF.

The subject is outside the shooting range. Turn Macro mode on or off (✽2).

The subject is moving too quickly. Use MF (pre-setting the shooting distance for a shot )

Cause Solution

✽1 Taking pictures using AF lock

Recompose the shot and take the picture.Capture the subject

◆Subjects not suitable for auto focus ◆

hVery shiny subjects such as a mirror or car

body

hSubjects photographed through glass

hSubjects that do not reflect well, such as hair

or fur

hSubjects with no substance, such as smoke

or flames

hWhen the subject is dark

hSubjects moving at high speed

hWhen there is very little contrast between the

subject and the background (such as white

walls or subjects dressed in the same color as

the background)

hWhen there is a high-contrast subject other

than the main subject at or near the center of

the image and that subject is closer to or

further from the camera than the main subject

(as when taking a picture of someone against

a background with contrasting colors)

Main subject

38 39

Advanced

Features

TAKING PICTURES — SELECTING THE CAMERA SETTINGS

STILL PHOTOGRAPHY FUNCTIONS

Consider the scene you are photographing and the sort of image you want to

achieve when you specify the camera settings. A general guide is given below.

1Select the Photography mode (➡P.40-44, 67-68).

BSpecifies all settings other than Quality, Sensitivity and FinePix COLOR

on the camera.

?Selects the best Scene Position setting (mPortrait, ,Landscape,

.Sports or /Night scene) for the scene being shot.

N/M/<Changes the aperture or shutter speed setting so that the action is

frozen, so that the flow of the motion is conveyed, or so that the

background is out of focus.

>Adjusts all the camera settings yourself.

rShoots a movie.

2Specify the photography settings (➡P.45-55).

dFlash Uses for shots in dark locations or for backlit subjects,

etc.

eMacro/ Super macro Uses for close-up shots.

EAE lock Fixes the exposure settings.

Exposure compensation

Uses the AE exposure as a reference value of 0, this

function brightens (+) or darkens (–) the shot.

fContinuous shooting Uses to take a series of continuous shots or to use

auto bracketing (with exposure compensation).

3Take the pictures (check the exposure and focus ➡adjust

the shot composition ➡press the Shutter button down fully).

★

You can use the menus for more detailed settings (➡P.32-35, 57-66).

The table below provides a number of sample settings. Use the settings effectively.

To achieve this result Sample settings

To express the motion of the subject Set the Mode dial to “M” and select a slow shutter speed. (Use a

tripod to avoid camera shake.)

To freeze the subject's movement Set the Mode dial to “M” and select a fast shutter speed.

To make the subject stand out by having the background

out of focus Set the Mode dial to “<” and select a wide aperture setting.

To get a very large depth of focus Set the Mode dial to “<” and select a narrow aperture setting.

To prevent the image having a red or blue cast due to

the light source

Change the “White balance” setting in the photography menu.

To avoid missing snapshot opportunities Take pictures in AUTO mode (see “Using the Camera”).

To prevent the subject from being overexposed or

underexposed and to show the substance and textures

of the subject clearly.

Use exposure compensation.

Select (+) if the background is pale and (–) if the background is

dark.

When shutter speed and aperture adjustments alone do not give the correct exposure.

When the image is too bright

Lower the Ssensitivity setting.

Use an ND filter (Sold separately).

When the image is too dark

Raise the Ssensitivity setting.

Use flash or the brightness adjustment

function.

dFlash

eMacro/ Super macro

EAE lock

Continuous

shooting

xAuto flash mode YES YES NO YES NO NO NO NO NO NO

YES YES NO NO NO YES YES YES YES NO

YES YES NO YES NO YES YES YES YES NO

NO YES NO NO YES YES NO YES NO NO

YES

NO NO NO YES

YES

DExposure compensation NO NO YES YES YES NO NO

YES YES YES YES YES YES NO

NO NO YES YES YES YES NO

YES YES YES YES YES YES NO

YES NO NO NO NO NO NO

bRed-eye reduction

dForced flash

NO YES NO NO YES YES NO YES NO NO

cSlow synchro

Red-eye reduction+ slow synchro

fTop 10-frame

Focus mode (S-AF/MF/C-AF)

jAuto bracketing

kFinal 10-frame

hLong-period (up to 40 frames)

Portrait

Landscape

Sports

Night scene

NM<>

Photography mode

Function

■List of functions available in each mode

✽The flash cannot be used for Continuous shooting and Super Macro.

✽Long-period continuous shooting and high-sensitivity photography cannot be used together.

✽1 The factory default quality for Movie mode is 640 ×480 pixels.

✽2 AUTO can only be set in “B” mode.

✽High-sensitivity photography cannot be used together with Long-period continuous shooting.

✽AREA cannot be used together with continuous AF (C-AF).

Photography

*Self-timer

AWhite balance

AF mode

´MULTI

CENTER

˜AREA

YESOFF

AUTO

CENTER

±1/3EV

NORMAL

YES YES YES YES YES NO

NO NO YES YES YES YES NO

jBracketing

MULTI NO NO YES YES YES YES NO

‘Photometry

GSharpness

OFF

NO NO YES YES YES YES NO

TMultiple exposure

zFlash brightness

adjustment

OFF

NO NO YES YES YES YES NO

∞External flash

Factory

Defaults ?NM<>

■List of menu options available in each mode

FinePix

Photo mode

AUTO

✽2

p-STANDARD

YES

YES YES YES YES YES

YES

✽1

NOYES YES YES YES YES

YES YES YES YES YES YES NO

yQUALITY

SISO

JFinePix COLOR

Other manuals for FinePix S20 Pro

Table of contents

Other FujiFilm Digital Camera manuals

FujiFilm

FujiFilm FinePix A345 User manual

FujiFilm

FujiFilm X-T3 Owner's manual

FujiFilm

FujiFilm FinePix REAL 3D W1 User manual

FujiFilm

FujiFilm FinePix S1 Pro Quick start guide

FujiFilm

FujiFilm FINEPIX F80EXR User manual

FujiFilm

FujiFilm 2400 User manual

FujiFilm

FujiFilm FinePix A345 User manual

FujiFilm

FujiFilm FinePix 3800 User manual

FujiFilm

FujiFilm X-H2 Installation guide

FujiFilm

FujiFilm Finepix S2000HD User manual

FujiFilm

FujiFilm INSTAX MINI 90 NOIR User manual

FujiFilm

FujiFilm FINEPIX F EXR User manual

FujiFilm

FujiFilm X-A3 User manual

FujiFilm

FujiFilm Finepix AV10 User manual

FujiFilm

FujiFilm FinePix50i User manual

FujiFilm

FujiFilm FinePix A120 User manual

FujiFilm

FujiFilm Finepix S700 User manual

FujiFilm

FujiFilm FinePixA204 User manual

FujiFilm

FujiFilm 16642939 User manual

FujiFilm

FujiFilm FINEPIX S7000 User manual

FujiFilm

FujiFilm Finepix S200 EXR Installation guide

FujiFilm

FujiFilm FinePix S8000FD User manual

FujiFilm

FujiFilm FinePix F410 User manual

FujiFilm

FujiFilm FinePix M603 User manual

Popular Digital Camera manuals by other brands

Sony

Sony Cyber-shot DSC-S2100 instruction manual

Sony

Sony DSC-WX60 instruction manual

GE POWER Pro series X5 Manuel d'utilisation

Argus

Argus Argus DC-5190 user manual

Nikon

Nikon COOLPIX 56200 quick start guide

Better Light

Better Light SuperModels Super 6K-HS Specifications

HP P650 user manual

Megxon

Megxon E301 user manual

D-Link

D-Link DCS-8350LH user manual

Intellisystem

Intellisystem IT I320SIR quick start guide

Leica

Leica SL instructions

Panasonic

Panasonic LUMIX DMC-G7H Basic owner's manual

Bosch

Bosch AUTODOME 7100i user manual

Ricoh

Ricoh RDC-6000 Operation manual

Argus

Argus DC1512 Specifications

Autoscope

Autoscope Image Sensing IntelliSight user manual

GE ACTIVE series G5WP Manual de usuario

Minolta

Minolta Dimge EX Specification sheet

FujiFilm FinePix S20 Pro User manual

Popular Digital Camera manuals by other brands