FujiFilm FinePix S5200 User manual

THE COMPONENTS IDENTIFIED WITH THE MARK “” ON THE SCHEMATIC
DIAGRAM AND IN THE PARTS LIST ARE CRITICAL FOR SAFETY.
PLEASE REPLACE ONLY WITH THE COMPONENTS SPECIFIED ON THE SCHEMATIC
DIAGRAM AND IN THE PARTS LIST.
IF YOU USE PARTS NOT SPECIFIED, IT MAY RESULT IN A FIRE AND AN
ELECTRICAL SHOCK.
FUJI PHOTO FILM CO., LTD. Ref.No.:ZM00608-100
Printed in Japan 2005.09
DIGITAL CAMERA
FinePix S5200/
S5600
US/CA/EU/EG/EE/AS/CH/JP-Model
SERVICE MANUAL
WARNING
BECAUSE THIS PRODUCTIS RoHS LEAD-FREE COMPLIANT, USE THE DESIG-
NATED AFTER-SELES PARTS AND THE DESIGNATED LEAD-FREE SOLDER WHEN
PERFORMING REPAIRS. (Refer to page 3 to page 5)
CAUTION

2
FinePix S5200/S5600 Service Manual
7. CAUTION: FOR CONTINUED
PROTECTION AGAINST FIRE
HAZARD, REPLACE ONLY WITH
SAME TYPE 2.5 AMPERES 125V
FUSE.
ATTENTION: AFIN D'ASSURER
UNE PROTECTION
PERMANENTE CONTRE LES
RISQUES D'INCENDIE,
REMPLACER UNIQUEMENT
PAR UN FUSIBLE DE MEME,
TYPE 2.5 AMPERES, 125 VOLTS.
8. WARNING:
TO REDUCE THE ELECTRIC
SHOCK, BE CAREFUL TO
TOUCH THE PARTS.
WARNING!
HIGH VOLTAGE
SAFETY CHECK-OUT
After correcting the original problem, perform the following
safety check before return the product to the customer.
1. Check the area of your repair for unsoldered or poorly
soldered connections. Check the entire board surface
for solder splasher and bridges.
2. Check the interboard wiring to ensure that no wires are
“pinched” or contact high-wattage resistors.
3. Look for unauthorized replacement parts, particularly
transistors, that were installed during a previous repair.
Point them out to the customer and recommend their
replacement.
4. Look for parts which, though functioning, show obvious
signs of deterioration. Point them out to the customer
and recommend their replacement.
5. Check the B + voltage to see it is at the values
specified.
6. Make leakage - current measurements to determine
that exposed parts are acceptably insulated from the
supply circuit before returning the product to the
customer.
2.5A 125V
2.5A 125V
RISK OF FIRE-
REPLACE FUSE
AS MARKED

3
FinePix S5200/S5600 Service Manual
RoHS lead-free compliance
Because this product is RoHS lead-free compliant, use the designated after-sales parts and the designated lead-free solder
when performing repairs.
<Background & Overview>
With the exception of parts and materials expressly excluded from the RoHS directive (*1), all the internal connections and
component parts and materials used in this product are lead-free compliant (*2) under the European RoHS directive.
*1: Excluded items (list of the main lead-related items)
• Lead included in glass used in fluorescent tubes, electronic components and cathode-ray tubes
• Lead in high-melting-point solder (i.e. tin-lead solder alloys that contain 85% lead or more)
• Lead in ceramic electronic parts (piezo-electronic devices)
• Mercury contained in fluorescent tubes is also excluded.
*2: Definition of lead-free
A lead content ratio of 0.1 wt% or less in the applicable locations (solder, terminals, electronic components, etc.)
<Reference>
RoHS: The name of a directive issued by the European Parliament aimed at restricting the use of
certain designated hazardous substances included in electrical and electronic equipment.
Designated substances (6): Lead, mercury, cadmium, hexavalent chromium, polybrominated biphenyls (PBBs) and
polybrominated diphenyl ether (PBDE)
<Lead-free soldering>
When carrying out repairs, use a designated lead-free solder, bearing in mind the differing work practices for conventional
solder (eutectic) and lead-free solder.


Differences in the soldering work for lead-free and eutectic solder
When the soldering work practices for eutectic solder and lead-free solder are compared, the main differences are as shown
below. In particular, when lead-free solder is used, the solder tends to be less workable than when eutectic solder is used.
Accordingly, the soldering techniques used must take that into account.
Difference
The solder starts melting later.
Poor wetting
Solder feed rate is difficult to control.
Wetting the insides of through holes is especially
difficult.
During repairs (or modifications) removing solder
from inside through holes is difficult.
There is serious carbonization of the soldering iron.
The surface is not glossy.
1
2
3
4
5
6
7
Countermeasure
The initial melting point of lead-free solder is high, so you
have to get used to it.
Move the tip of the soldering iron around to heat the entire
connection to the melting temperature and assist wetting.
Use the solder (wire) diameter and soldering iron that are
best suited to connection being soldered.
First apply solder to the area immediately around the
through hold and then feed the solder into the hole.
Use a suitable wicking wire (with a suitable method and
heating) and a suction tool.
Either put solder onto the soldering iron tip after completing
the work, or turn the iron off frequently.
Learn to recognize the appearance of the surface.

4
FinePix S5200/S5600 Service Manual


Setting temperature during lead-free soldering
• Lead-free solder melting temperature
The melting point of eutectic (Sn-Pb) solder is 183°C, while the melting point of lead-free solder (Sn-Ag-Cu) is 30°C higher
at 220°C.
• Soldering iron tip temperature
The temperature setting for the soldering iron used should be such that the tip of the soldering iron is at the correct
bonding temperature for the connection. This temperature is normally set at around 100°C higher than the melting point of
the solder.
However, the actual temperature should take into account the shape and size of the soldering iron tip, the heat tolerance
of the connection and the workability of that temperature.
• Correct bonding temperature
The correct bonding temperature refers not to the temperature of the heat source, but to the bonding temperature that will
give the best bond strength.


Precautions when soldering with lead-free solder
• Soldering iron maintenance
Because of the high soldering iron temperature in lead-free soldering, there is rapid carbonization of the flux adhering to
the tip of the soldering iron.
(1) Always cover the tip of the soldering iron with solder when it is not being used.
(2) If the tip is black from carbonization, wipe it gently with a paper towel soaked in alcohol until the solder will wet.
• Uniform heating of the board and components
To ensure that the lead-free solder wets the entire surface of the pattern and the lands despite its poor wetting
characteristics, you must move the tip of the soldering iron over a wide area to raise the temperature of the entire
connection.


Soldering iron
A soldering iron with a temperature control is best.

5
FinePix S5200/S5600 Service Manual
lead-free
Wire diameter 0.8mm
Solder type (Displayed symbol)
SnAgCu


Solder wire (thread)
Use the lead-free solders specified below.
Solder type: Sn96.5Ag3Cu0.5 (Displayed symbol: SnAgCu)
Wire diameter: 0.6, 0.8 or 1.0 mm
Sample:


Flux
Conventional flux can be used.


Solder application wires (mesh, wicking wire, etc.)
Conventional application wires can be used.

6
FinePix S5200/S5600 Service Manual
CONTENTS
CONTENTS
1. General .................................................................. 7
1-1. Product specification ........................................................... 7
1-2. Explanation of Terms ......................................................... 11
1-3. Names of External Components ....................................... 12
2. Disassembly ......................................................... 14
2-1. Names of internal Components ......................................... 14
2-2. Removing the CONST REAR ............................................ 15
2-3. Disassembling the CONST REAR .................................... 17
2-4. Removing the MAIN PWB ASSY and ST PWB ASSY ...... 18
2-5. Removing the HOLDER BATTERY ................................... 20
2-6. Removing the LENS CONST ............................................ 21
2-7. Removing the CONST FLASH .......................................... 22
2-8. Disassembling the CONST FRONT .................................. 23
2-9.
Adhesion Position Specifications for Sheet Components ....... 23
3. Schematics........................................................... 25
3-1. Cautions ............................................................................. 25
3-2. Basic Block Names and Functions .................................... 25
3-3. Description of Main Block Functions ................................. 26
3-3-1. Technical Overview ............................................... 26
3-4. Block Diagram ................................................................... 27
3-5. Overall connection Diagram .............................................. 28
3-6. Circuit Diagrams ................................................................ 29
3-6-1. CAMERA BLOCK ................................................. 29
3-6-2. DCDC BLOCK ...................................................... 30
3-6-3. KEY BLOCK ......................................................... 31
3-6-4. KSW BLOCK ........................................................ 32
3-6-5. LCD/EVF BLOCK ................................................. 33
3-6-6. MOTOR BLOCK ................................................... 34
3-6-7. PMAN BLOCK ...................................................... 35
3-6-8. PROCESS BLOCK ............................................... 36
3-6-9. STJACK BLOCK ................................................... 37
3-6-10. AF LED BLOCK .................................................... 39
3-6-11. BL FPC BLOCK .................................................... 39
3-6-12. AUDIO BLOCK ..................................................... 40
3-6-13. CCD FPC BLOCK ................................................. 41
3-6-14. FLASH PLUNGER BLOCK .................................. 41
3-6-15. CN BLOCK ........................................................... 42
3-6-16. FSW BLOCK ......................................................... 42
3-6-17. EMI BLOCK .......................................................... 43
3-6-18. LED FPC BLOCK ................................................. 44
3-6-19. MEDIA BLOCK ..................................................... 44
3-6-20. MSW BLOCK ........................................................ 44
3-6-21. RSW BLOCK ........................................................ 45
3-6-22. USB BLOCK ......................................................... 45
3-6-23. VIDEO BLOCK ..................................................... 46
3-6-24. XE BLOCK ............................................................ 46
3-7. Mounted Parts Diagrams ................................................... 47
3-7-1. AF FPC ASSY ....................................................... 47
3-7-2. BL FPC ASSY ....................................................... 48
3-7-3. CCD FPC ASSY ................................................... 50
3-7-4. ST PWB ASSY ...................................................... 52
3-7-5. FSW PWB ASSY .................................................. 54
3-7-6. MSW PWB ASSY ................................................. 55
3-7-7. RSW PWB ASSY .................................................. 55
3-7-8. KSW PWB ASSY .................................................. 56
3-7-9. MAIN PWB ASSY ................................................. 58
3-7-10. XE PWB ASSY ..................................................... 60
4. Adjustments ......................................................... 61
4-1. Important point Adjustment when Replacing Major Parts ....... 61
4-2. Measuring Instruments Used ............................................ 61
4-3. Use Jig list ......................................................................... 61
4-4. Calibration method of pattern box ..................................... 62
4-5. Adjustment software installation ........................................ 62
4-5-1. Various downloading software decompressions,
preservation methods, and notes ......................... 62
4-5-2. Installation of DSC jig driver ................................. 63
4-5-3. Adjustment software initiation method .................. 63
4-6. Initial Settings of the Adjustment Software ........................ 64
4-7. Starting the Adjustment Software ...................................... 67
4-8. [R] : Flash Memory Reset .................................................. 70
4-9. [L] : LENS Data Input ......................................................... 72
4-10. [F4] : CCD Data Input ........................................................ 74
4-11. [F5] : CAMERA Adjustment ............................................... 76
4-12. [F6] : AF Adjustment .......................................................... 82
4-13. [F1] : Battery Voltage Adjustment ...................................... 85
4-14. [F7] : Flash Adjustment ...................................................... 89
4-15. [F11] : Video Adjustment .................................................... 91
4-16. [F8] : Firmware Download ................................................. 93
4-17. [F12] : End Setting ............................................................. 95
5. Inspection ............................................................. 99
5-1. Required Measuring Equipment ........................................ 99
5-2. Connection of Measuring Equipment ................................ 99
5-3. Inspection and Factory Settings ...................................... 100
6. Parts List ............................................................ 104
6-1. Packing and Accessories ................................................ 104
6-1-1. US-model (FinePix S5200) ................................. 104
6-1-2. CA-model (FinePix S5200) ................................. 105
6-1-3. EU-model (FinePix S5600) ................................. 106
6-1-4. EG-model (FinePix S5600) ................................. 107
6-1-5. EE-model (FinePix S5600) ................................. 108
6-1-6. AS-model (FinePix S5600) ................................. 109
6-1-7. CH-model (FinePix S5600) ................................. 110
6-1-8. JP-model (FinePix S5200) .................................. 111
6-2. Cabi Front Block .............................................................. 112
6-2-1. US/CA/JP-model (FinePix S5200) ..................... 112
6-2-2. EU/EG/EE-model (FinePix S5600) ..................... 113
6-2-3. AS-model (FinePix S5600) ................................. 114
6-2-4. CH-model (FinePix S5600) ................................. 115
6-3. Cabi Rear Block ............................................................... 116
6-3-1. US/CA/EU/EG/EE/AS-model
(FinePix S5200/S5600) ...................................... 116
6-3-2. CH-model (FinePix S5600) ................................. 117
6-3-3. JP-model (FinePix S5200) .................................. 118
6-4. Electrical parts ................................................................. 119
7. Appendix ............................................................ 120
7-1. List of Related Technical Updates Issued ....................... 120

7
1. General
FinePix S5200/S5600 Service Manual
1. General
1-1. Product specification
System
Model Digital camera FinePix S5200 / FinePix S5600
Effective pixels 5.1 million pixels
CCD 1/2.5-inch Super CCD HR
Number of total pixels: 5.22 million pixels
Storage media xD-Picture Card (16/32/64/128/256/512 MB/1 GB)
File format Still image: DCF-compliant
Compressed: Exif ver.2.2 JPEG, DPOF-compatible
Uncompressed: CCD-RAW (RAF)
* Design rule for Camera File System compliant DPOF compatible
Movie: AVI format, Motion JPEG
Audio: WAVE format, Monaural sound
Number of recorded pixels Still image: 2592
× 1944 pixels/2736 × 1824 pixels ( )/
2048
× 1536 pixels/1600 × 1200 pixels/640 × 480pixels
Lens Fujinon 10
× optical zoom lens
F3.2-F3.5
Focal length f=6.3 mm-63 mm
(Equivalent to approx. 38 mm-380 mm on a 35 mm camera)
Digital zoom Approx. 5.7
×
(10 × optical zoom lens is used together: Max. zoom scale: 57 × )
Aperture (Wide-angle) F3.2 to F8 9 steps 1/3 EV steps
Focal range Normal: Wide-angle: approx. 90 cm (3.0 ft.) to infinity (In High-speed shooting mode: approx.
2 m (6.6 ft.) to infinity)
Telephoto: approx. 2 m (6.6 ft.) to infinity (In High-speed shooting mode: approx.
4 m (13.1 ft.) to infinity)
Macro: Wide-angle: approx. 10 cm (3.9 in.) to 2 m (6.6 ft.) (In High-speed shooting mode:
approx. 10 cm (3.9 in.) to 2 m (6.6 ft.))
Telephoto: approx. 90 cm (1.5 ft.) to 2 m (6.6 ft.) (In High-speed shooting mode:
approx. 90 cm (1.5 ft.) to 2 m (6.6 ft.))
Sensitivity AUTO/Equivalent to ISO 64/100/200/400/800/1600
Photometry TTL 64-zones metering Multi, Spot, Average
Exposure control Program AE ( , , , , , , P), Shutter-priority AE,
Aperture-priority AE, Manual exposure
Scene position (Anti-blur), (Natural light), (Portrait), (Landscape), (Night)
Exposure compensation -2 EV to +2 EV in 1/3 EV-step increments
Shutter speed 15 sec. to 1/2000 sec. (depend on Exposure mode)
Continous shooting Top 3-frame: Number of recorded frames: up to 3 frames
(Max. 2 frames/sec.)
Final 3-frame:Number of recorded frames:
last 3 frames before releasing the shutter button
(Max. 2 frames/sec.)
Long-period continuous shooting mode:
Number of recorded frames: up to 40 frames.
(Max. 0.9 frames/sec.)
Auto bracketing ± 1/3 EV, ± 2/3 EV, ± 1 EV
Focus Mode: Single AF/Continuous AF/Manual focus
AF system: TTL contrast-type, AF-assist illuminator
AF frame selection: AF (CENTER), AF (MULTI), AREA AF

8
1. General FinePix S5200/S5600 Service Manual
System
White balance Automatic scene recognition/Preset (Fine, Shade, Fluorescent (Daylight), Fluorescent
(Warm White), Fluorescent (Cool White), Incandescent)/Custom
Self-timer Approx. 10 sec./2 sec.
Flash type Popping the flash up automatically
Effective range (AUTO): Wide-angle: approx. 30 cm-4 m (1.0 ft.-13.1 ft.)
Telephoto: approx. 80 cm-4 m (2.6 ft.-13.1 ft.)
Flash mode Auto, Red-Eye Reduction, Forced Flash, Suppressed Flash,
Slow Synchro, Red-Eye Reduction + Slow Synchro
Viewfinder 0.33 inches, 115,000 pixels electronic viewfinder, Approx. 100 % coverage
LCD monitor 1.8 inches, Aspect ratio: 4:3; approx. 115,000 pixels TFT color LCD monitor,
Approx. 100% coverage
Movie 640
× 480 pixels/320 × 240 pixels ( / )
(30 frames per second with monaural sound)
A series of continuous image can be recorded up to available recording time per xD-
Picture Card. Zoom cannot be used during movie recording.
Photography functions Post shot assist window, High-speed shooting, Best framing,
Frame No. memory
Playback functions Trimming, Image rotate, Automatic playback, Multi-frame playback,
Sorting by date, Histograms (Highlight warning), Voice memo
Other functions PictBridge, Exif print, PRINT Image Matching II, Language (English, Francais, Deutsch,
, Italiano, , ), Time difference, FinePix photo mode ( -mode)
Input/Output Terminals
A/V OUT NTSC/PAL-type (with monaural sound)
(Audio/Visual output)
Digital input/output USB2.0 High-Speed
DC input socket AC-5VX/AC-5VH/AC-5VHS (sold separately)
Quality setting
DPC-16 (16 MB)
DPC-32 (32 MB)
DPC-64 (64 MB)
DPC-128 (128 MB)
DPC-256 (256 MB)
Image data size
Number of recorded pixels
F
2592 1944
2736 1824 2048 1536 1600 1200 640 480 640 480 320 240
N(30 fps) (30 fps)
6
12
25
51
102
2.5 MB
DPC-512/M512 (512 MB)
DPC-M1GB (1 GB)
205
412
12
25
50
102
204
1.3 MB
409
819
12
25
51
103
207
1.3 MB
414
830
19
40
81
162
325
780 KB
651
1305
25
50
101
204
409
630 KB
818
1639
122
247
497
997
1997
130 KB
3993
7995
1
2
5
11
23
11 MB
46
92
13 sec.
27 sec.
55 sec.
111 sec.
223 sec.
7.4 min.
14.9 min.
26 sec.
54 sec.
109 sec.
219 sec.
7.3 min.
14.6 min.
29.3 min.
Standard number of available frames/recording time per xD-Picture Card
The number of available frames, recording time or file size varies slightly depending on the subjects photographed. Note also
that the divergence between standard number of frames and the actual number of frames is greater for
xD-Picture Cards with higher capacities.

9
1. General
FinePix S5200/S5600 Service Manual
Guide to the number of
available frames for battery
operation
Power Supply and Others
Power supply • 4 × AA-size alkaline batteries
• 4
× AA-size Ni-MH (Nickel-Metal Hydride) batteries (sold separately)
According to the CIPA (Camera & Imaging Products Association) standard procedure for
measuring digital still camera battery consumption (extract):
When using alkaline batteries, use the batteries supplied with the camera. You can use
Ni-MH batteries also. The storage media should be xD-Picture Card or Microdrive.
Pictures should be taken at a temperature of +23oC (+73oF), with the LCD monitor turned
on, AF-assist illuminator off, the optical zoom moved from full wide-angle to full telephoto
(or vice-versa) and back again to its original position every 30 seconds, the flash used at
full power every second shot and the camera turned off and then on again once every 10
shots.
• Note: Because the number of available shots varies depending on the capacity of
alkaline batteries or the level of charge in Ni-MH batteries, the figures shown here
for the number of available shots using batteries are not guaranteed.
The number of available shots will also decline at low temperatures.
Camera dimensions 113.5 mm
× 85.0 mm × 112.0 mm/4.4 in. × 3.3 in. × 4.4 in.
(W/H/D) (not including accessories and attachments)
Camera mass (weight) Approx. 370 g/13.1 oz.
(not including accessories, batteries and xD-Picture Card)
Weight for photography Approx. 470 g/16.6 oz. (including batteries and xD-Picture Card)
Operating conditions Temperature: 0oC to +40oC (+32oF to +104oF)
80% humidity or less (no condensation)
Accessories included zAA-size Alkaline Batteries (LR6) (4)
z16 MB, xD-Picture Card (1) Anti-static case (1) included
zShoulder Strap (1)
zLens cap (1)
zA/V cable (1) Approx. 1.2 m (3.9 ft.), plug (2.5 mm dia.) to pin-plug
× 2
zUSB cable (mini-B) (1)
zCD-ROM (1) Software for FinePix CX
zOwner’s Manual (1)
Alkaline batteries Approx. 250 frames Approx. 270 frames
Ni-MH batteries 2500 mAh Approx. 500 frames Approx. 540 frames
Battery Type With LCD monitor ON
With viewfinder (EVF) ON

10
1. General FinePix S5200/S5600 Service Manual
Power Supply and Others
Optional accessories zxD-Picture Card
DPC-16 (16 MB)/DPC-32 (32 MB)/DPC-64 (64 MB)/DPC-128 (128 MB)/
DPC-256 (256 MB)/DPC-512 (512 MB)/DPC-M512 (512 MB)/DPC-M1GB (1 GB)
zAC Power Adapter AC-5VX
zFujifilm Rechargeable Battery 2HR-3UF
zFujifilm Battery Charger with Battery BK-NH2 (With Euro type or UK type plug)
zAC Power Adapter AC-5VH/AC-5VHS
zSoft Case SC-FXS5
zWide Conversion Lens WL-FX9B
zImage Memory Card Reader DPC-R1
• Compatible with Windows 98/98 SE, Windows Me, Windows 2000 Professional,
Windows XP or iMac, Mac OS 8.6 to 9.2.2, Mac OS X (10.1.2 to 10.2.2) and
models that support USB as standard.
• Compatible with xD-Picture Card of 16 MB to 512 MB, and SmartMedia of 3.3 V, 4
MB to 128 MB.
zPC Card Adapter DPC-AD
• Compatible with xD-Picture Card of 16 MB to 512 MB, and SmartMedia of 3.3 V, 2
MB to 128 MB.
zCompactFlash Card Adapter DPC-CF
• Windows 95/98/98 SE/Me/2000 Professional/XP
• Mac OS 8.6 to 9.2/X (10.1.2 to 10.1.5)
zxD-Picture Card USB Drive DPC-UD1
• Compatible with xD-Picture Card of 16 MB to 512 MB
• Windows 98/98 SE/Me/2000 Professional/XP
• Mac OS 9.0 to 9.2.2/X (10.0.4 to 10.2.6)

11
1. General
FinePix S5200/S5600 Service Manual
1-2. Explanation of Terms
Deactivated batteries: Leaving an Ni-MH battery unused in storage for a long period may cause a rise in the level
of substances that inhibit current flow inside the battery and result in a dormant battery. A
battery in this state is referred to as deactivated.
Because current flow is inhibited in a deactivated Ni-MH battery, the battery’s original
level of performance cannot be achieved.
EV: A number denotes Exposure Value. The EV is determined by the brightness of the subject
and sensitivity (speed) of the film or CCD. The number is larger for bright subjects and
smaller for dark subjects. As the brightness of the subject changes, a digital camera
maintains the amount of light hitting the CCD at a constant level by adjusting the aperture
and shutter speed.
When the amount of light striking the CCD doubles, the EV increases by 1. Likewise, when
the light is halved, the EV decreases by 1.
Frame rate (fps): The frame rate refers to the number of images (frames) that are photographed or played
back per second. For example, when 10 frames are continuously photographed in a 1-
second interval, the frame rate is expressed as 10 fps.
For reference, TV images are displayed at 30 fps (NTSC).
JPEG: Joint Photographic Experts Group
A file format used for compressing and saving color images. The higher the compression
rate, the greater the loss of quality in the decompressed (restored) image.
Memory effect: If an Ni-MH battery is repeatedly charged without first being fully discharged, its perfor-
mance may drop below its original level. This is referred to as the “memory effect”.
Motion JPEG: A type of AVI (Audio Video Interleave) file format that handles images and sound as a
single file. Images in the file are recorded in JPEG format. Motion JPEG can be played
back by QuickTime 3.0 or later.
Smear: A phenomenon specific to CCDs whereby white streaks appear on the image when there
is a very strong light source, such as the sun or reflected sunlight, in the photography
screen.
WAVE: A standard format used on Windows systems for saving audio data. WAVE files have the
“.WAV” file extension and the data can be saved in either compressed or uncompressed
format. Uncompressed recording is used on this camera.
WAVE files can be played back on a personal computer using the following software:
Windows: MediaPlayer
Macintosh: QuickTime Player
* QuickTime 3.0 or later
White Balance: Whatever the kind of the light, the human eye adapts to it so that a white object still looks
white. On the other hand, devices such as digital cameras see a white subject as white by
first adjusting the color balance to suit the color of the ambient light around the subject.
This adjustment is called matching the white balance.
Exif Print: Exif Print Format is a newly revised digital camera file format that contains a variety of
shooting information for optimal printing.

12
1. General FinePix S5200/S5600 Service Manual
1-3. Names of External Components
Exposure compensation
button
Focus mode
selector button
Continuous shooting
button
Shutter button
Focus mode
selector lock switch
Mode dial
Still Photography Movie recording
Power switch
Playback mode
Power-OFF
Photography mode
Auto Programmed Auto
Manual
Anti-blur
Aperture-priority Auto
Shutter-priority Auto
Movie
Natural light
Night
Portrait
Landscape
Strap mount
Slot cover
USB socket
DC IN 5V (power input) socket
A/V OUT (Audio / Visual output)
socket
Microphone
Flash
A
F-assist
illuminator
Self-timer lamp
Speaker
xD-Picture Card slot
Lens

13
1. General
FinePix S5200/S5600 Service Manual
W (Wide zoom) button
Photo mode ( ) button
DISP (display) / BAC
K
button
Low light view
button
Battery cove
r
MENU/OK button
T (Tele zoom) button
Strap moun
t
Viewfinder (EVF)
Diopter adjustment dial
EVF/LCD
(monitor selector)
button
Tripod mount
LCD monitor
Indicator lamp
Playback modePhotography mode
/ Erase button
4-direction ( ) button
/ Macro button
/ Flash button

14
2. Disassembly FinePix S5200/S5600 Service Manual
2. Disassembly
2-1. Names of internal Components
CONST FLASH
EVF UNIT CONST
LCD CONST
MAIN PWB ASSY
KSW PWB ASSY
MSW PWB ASSY
FRAME LCD
ST PWB ASSY
MIC ASSY
SPEAKER ASSY
FRAME MAIN
COVER JACK
ASSY CASE F
ASSY CASE R
A
SSY HOLDER BATTRY
LID BATTRY
CONST AF LED
RSW PWB ASSY
ASSY CASE LENS
LENS CONST

15
2. Disassembly
FinePix S5200/S5600 Service Manual
1
2
2
4
3
A
A
2-2. Removing the CONST REAR
(1) Remove the 2 screws (M1.7 x 9.0).
(2) Remove the 3 screws (M1.7 x 3.5).
(3) Apply pressure in the direction indicated by the arrow to
disengage the catches at (A).
(4) Slowly remove the CONST REAR in the direction of the
arrow.

16
2. Disassembly FinePix S5200/S5600 Service Manual
B
5
6
B
Long
Short
SW551
(5) Unlock connector CN451 and then remove the LCD
FPC.
(6) Unlock connector CN801 and then remove the MAIN-
KSW FPC.
Take care that the metal catch (B) on the FRAME LCD
does not touch the MAIN PWB ASSY.
[Assembly]
Re-assemble by reversing the disassembly procedure.
[Notes on assembly]
Fit the CONST REAR into the CASE F with the COVER
CARD open (to prevent damage to SW551).

17
2. Disassembly
FinePix S5200/S5600 Service Manual
6
7
1
2
3
45
8
13
10
14
11
9
12
2-3. Disassembling the CONST REAR
(1) Remove the 5 screws (M1.7 x 4.0).
(2) Remove the FRAME LCD.
(3) Unlock connector CN802 and then remove the KSW-
MSW FFC.
(4) Remove the screw (M1.7 x 4.0).
(5) Push the MSW PWB lock catch in the direction of the
arrow to disengage it.
(6) Remove the MSW PWB in the direction of the arrow.
(7) Remove the 2 screws (M1.7 x 4.0).
(8) Remove the KSW PWB in the direction of the arrow.
(9) Remove the LCD CONST in the direction of the arrow.
(10) Remove the BUTTON REAR in the direction of the
arrow.
(11) Remove the BUTTON ZOOM in the direction of the
arrow.
(12) Remove the screw (M1.7 x 4.0).
(13) Remove the STRAP RIGHT in the direction of the
arrow.
(14) Remove the ASSY CURSOL in the direction of the
arrow.
[Assembly]
Re-assemble by reversing the disassembly procedure.
[Notes on assembly]
When fitting the MSW PWB into the CASE R, set the DIAL
MODE to "AUTO" and set the selector dial on the MSW
PWB to the position shown in the figure before assembly.

18
2. Disassembly FinePix S5200/S5600 Service Manual
2
1
2
1
2
3
4
1
1
5
6
7
B to B
CONNECTOR
2-4. Removing the MAIN PWB ASSY and ST PWB ASSY
(1) Disconnect the 4 harness couplings in the direction of
the arrows.
(2) Remove the 3 FPCs in the direction of the arrows.
(3) Remove the FPC in the direction of the arrow.
(4) Remove the EVF UNIT in the direction of the arrow.
(5) Remove the 3 screws (M1.7 x 2.5).
(6) Unlock connector CN151 and remove the FPC.
(7) Remove the B to B CONNECTOR and remove the
MAIN PWB ASSY in the direction of the arrow.

19
2. Disassembly
FinePix S5200/S5600 Service Manual
11
12
10
9
13
8
15
14
J702
AC
B
(8) Unlock connector CN101 and remove the FPC.
(9) Peel off the TAPE CONDENSER.
Note that touching the main capacitor terminals will
cause an electric shock.
(10) Discharge across the main capacitor terminals.
(11) Press on the upper part of the CN701 connector
catch.
(12) Remove the connector in the direction of the arrow.
(13) Remove connector CN701 in the direction of the
arrow.
(14) Remove the 3 screws (M1.7 x 2.5).
(15) Push the ST PWB ASSY to the right to disengage it
from J702 and then pull it outwards to remove it.
[Assembly]
Re-assemble by reversing the disassembly procedure.
[Notes on assembly]
(1) ST PWB ASSY
Engage the ST PWB ASSY and the CASE F bosses in
the correct positions.
(2) MAIN PWB ASSY
A. Ensure that the wire harnesses for the SPEAKER
ASSY and MIC ASSY also run underneath the FSW
PWB.
B. Align the PLUNGER wire harness with the notch in
the PWB and then run it down and to the left.
C. Take care to ensure that the FLASH wire harness
does not protrude either left or right.

20
2. Disassembly FinePix S5200/S5600 Service Manual
12
2-5. Removing the HOLDER
BATTERY
(1) Remove the screw (M1.7 x 9.0).
(2) Remove the HOLDER BATTERY in the direction of the
arrow.
[Assembly]
Re-assemble by reversing the disassembly procedure.
[Notes on assembly]
When assembling the HOLDER BATTERY, ensure that the
LEVER RELEASE is set to OFF (to prevent damage to
SW902 and SW903).