FujiFilm X-T3 User manual

Owner’s Manual
BL00004970-20Z EN

EN_2
Introduction
Thank you for your purchase of this product. Be sure that
you have read this manual and understood its contents be-
fore using the camera. Keep the manual where it will be
read by all who use the product.
For the Latest Information
The latest versions of the manuals are available from:
http://fujifilm-dsc.com/en/manual/
The site can be accessed not only from your
computer but also from smartphones and
tablets.
For information on rmware updates, visit:
http://www.fujifilm.com/support/digital_cameras/software/

EN_3
About This Manual
This manual contains instructions for your FUJIFILM X-T3
digital camera. Be sure you have read and understood its
contents before proceeding.
Symbols and Conventions
The following symbols are used in this manual:
O
Information that should be read to prevent damage to the
product.
N
Additional information that may be helpful when using the
product.
PPages on which related information may be found.
Menus and other text in the displays are shown in bold. Illustrations
are for explanatory purposes only; drawings may be simplied,
while photographs are not necessarily taken with the model of
camera described in this manual.
Terminology
The optional SD, SDHC, and SDXC memory cards the camera uses
to store pictures are referred to as“memory cards”. The electronic
viewnder may be referred to as the “EVF” and the LCD monitor
as the “LCD”.

EN_4
Charging the Battery
The battery is not charged at shipment. Before use, charge
the battery in the supplied battery charger.
O
An NP-W126S rechargeable battery is supplied with the camera.
Charging takes about 150 minutes.
1 Place the battery in the charger.
Place the battery in the supplied bat-
tery charger as shown.
CHARGE
2 Plug the charger in.
Plug the charger into an indoor pow-
er outlet. The charging indicator will
light.
3 Charge the battery.
Remove the battery when charging is complete.

EN_5
Charging the Battery
The Charging Indicator
The charging indicator shows battery charge
status as follows:
Charging indicator
Charging indicator
Battery status
Battery status
Action
Action
Off Battery not inserted. Insert the battery.
Battery fully charged. Remove the battery.
On Battery charging. —
Blinks Battery fault. Unplug the charger and
remove the battery.
O
The supplied AC cord is for use exclusively with the supplied battery
charger. Do not use the supplied charger with other cords or the sup-
plied cord with other devices.
Do not ax labels or other objects to the battery. Failure to observe
this precaution could make it impossible to remove the battery from
the camera.
Do not short the battery terminals. The battery could overheat.
Read the cautions in “The Battery and Power Supply”.
Use only battery chargers designated for use with the battery. Failure
to observe this precaution could result in product malfunction.
Do not remove the labels from the battery or attempt to split or peel
the outer casing.
The battery gradually loses its charge when not in use. Charge the
battery one or two days before use. If the battery fails to hold a charge,
it has reached the end of its charging life and must be replaced.
Unplug the charger when it is not in use.
Remove dirt from the battery terminals with a clean, dry cloth. Failure
to observe this precaution could prevent the battery from charging.
Note that charging times increase at low or high temperatures.

EN_6
Charging the Battery
Charging via Computer
The battery also charges if the camera is connected to a computer. Turn the
camera o, insert the battery, and connect a USB cable as shown, making
sure the connectors are fully inserted.
Battery status is shown by the indicator lamp.
Indicator lamp
Indicator lamp
Battery status
Battery status
On Battery charging
Off Charging complete
Blinks Battery fault
Connect the camera directly to the computer; do not use a USB hub or
keyboard. Charging stops if the computer enters sleep mode; to resume
charging, activate the computer and disconnect and reconnect the USB
cable. Charging may not be supported depending on the model of com-
puter, computer settings, and the computer’s current state.
USB connector(Type-C)

EN_7
Inserting the Battery
After charging the battery, insert the battery in the camera
as described below.
1 Open the battery-chamber cover.
Slide the battery-chamber latch as
shown and open the battery-cham-
ber cover.
O
Do not open the battery-chamber
cover when the camera is on. Fail-
ure to observe this precaution could
damage image les or memory cards.
Do not use excessive force when han-
dling the battery-chamber cover.
2 Insert the battery.
Using the battery to keep the battery
latch pressed to one side, insert the
battery contacts rst in the direction
shown by the arrow. Conrm that
the battery is securely latched.
O
Insert the battery in the orientation
shown. Do not use force or attempt
to insert the battery upside down or
backwards. The battery will slide in
easily in the correct orientation.

EN_8
Inserting the Battery
3 Close the battery-chamber cover.
Close and latch the cover.
O
If the cover does not close, check that
the battery is in the correct orienta-
tion. Do not attempt to force the cov-
er shut.
Removing the Battery
Before removing the battery, turn the camera o and open the battery-cham-
ber cover.
To remove the battery, press the battery latch to
the side, and slide the battery out of the camera
as shown.
O
The battery may become hot when used in high-temperature environ-
ments. Observe caution when removing the battery.

EN9
Inserting Memory Cards
Pictures are stored on memory cards (sold separately).
N
The camera can be used with two cards, one in each of its two slots.
1 Open the memory card slot cover.
Unlatch and open the cover.
O
Do not open the memory card-slot cover when the camera is on.
Failure to observe this precaution could damage image les or
memory cards.
2 Insert the memory card.
Holding the card in the orientation
shown, slide it in until it clicks into
place at the back of the slot. Close
and latch the memory card slot cover.
O
Be sure card is in the correct orientation; do not insert at an angle
or use force.
3 Format the memory card.
O
Format memory cards before rst use, and be sure to reformat all
memory cards after using them in a computer or other device.

EN10
Removing Memory Cards
Before removing memory cards, turn the camera o and open the memory
card slot cover.
Press and release the card to eject it part way (to
prevent the card falling from the slot, press the
center of the card and release it slowly, without
removing your nger from the card). The card
can then be removed by hand.
Using Two Cards
The camera can be used with two cards, one in each of its two
slots. At default settings, photos are saved to the card in the sec-
ond slot only when the card in the rst slot is full. This can be
changed using DSAVE DATA SET-UP> CARD SLOT SETTING
(STILL IMAGE).
Option
Option
Description
Description
Display
Display
SEQUENTIAL
(default)
The card in the second slot is used only when the card in
the first slot is full. If the second slot is selected for DSAVE
DATA SET-UP> SELECT SLOT(xSEQUENTIAL), re-
cording will start on the card in the second slot and switch
to the first slot when the card in the second slot is full.
BACKUP Each picture is recorded twice, once to each card.
RAW / JPEG
As for SEQUENTIAL, except that the RAW copy of pictures
taken with FINE+RAW or NORMAL+RAW selected for
H IMAGE QUALITY SETTING> IMAGE QUALITY will
be saved to the card in the first slot and the JPEG copy to
the card in the second slot.
The card used to store movies can be selected using DSAVE
DATA SET-UP> SELECT SLOT(FSEQUENTIAL).