Fujitsu LifeBook S-61 Series User manual

T e c h n i c a l P r o c e d u r e
LifeBook S-61xx
Disassembly Procedure
1. To begin the disassembly proce-
dure, make sure the unit is powered
off. Remove the battery.
4. Remove two screws securing the
cover to the hard disk drive. Detach
the drive’s data cable and lift it out
of its compartment.
3. Remove two screws securing the
memory module cover. Lift off the
cover, unlock the module, and
remove it.
2. Slide the CD/DVD drive out from
its bay.

2
7. Detach the speakers’ cable and lift
off the cover. 8. Tilt up the keyboard so as to
unlock and remove its data cable.
Lift it off.
9. Detach the antennae cable and
modem cable from the wireless
LAN module. Unlock the module
and remove it.
10. Detach the LCD’s power and data
cables at the upper left.
5. Remove a total of 14 case screws.
6. Pry jup the hinge cover. Unlock
and remove the cable to the status
LCD.

3
13. Remove seven screws securing
the top cover.
11. Remove two hinge screws at at
the rear.
12. Remove two hinge screws at the
upper corners. Lift off the LCD.
14. Unlock and release the touchpad
cable.
15. Pry around the edges to separate
the top cover and then lift it off. 16. Remove four screws securing the
heat sink. Detach the hard disk
drive cable.

19. Lift off the modem cable and port.
17. Remove two hex nuts on either
side of the VGA port. Lift off
the heat sink.
22. Remove three screw caps and
the screws underneath to dis-
assemble the LCD.
21.Remove two screws securing
the cooling fan. Turn the board
over. Detach the fan’s power
cable and lift the fan off.
20. Maneuver the motherboard out of
the lower cover.
18. Then lift off the connecting board.
4

5
25. Lift up the LCD panel to access
and detach its cable to the invert-
er. The inverter can be lifted
from the rear cover.
24. Remove two screws securing the
locking clip and two at the lower
corners.
23. Pry around the edges of the frame
to separate it from the rear cover.
26. Detach the antennae cable.
Remove a screw securing the
antennae and lift it off the rear
cover.

Te c h n i c a l P r o c e d u r e
LifeBook S-61xx
Assembly Procedure
1. Replace the antennae and secure it.
Attach its cable. 2. Position the inverter in the rear
cover. Attach the LCD’s cable to
the inverter and then tilt the panel
into the cover.
3. Secure the panel and its latch with
four screws.
4. Press the frame onto the rear cover
and secure it with three screws.
6

7
7. Position the modem port and cable.
5. Connect the cooling fan’s power
cable. Turn the board over and
secure the fan with two screws. 6. Maneuver the motherboard into the
lower cover.
8. Position the connecting board in
the lower cover.
9. Lower the heat sink onto the lower
assembly. Replace two hex nuts at
the VGA port and secure the
heatsink with four screws.
10. Connect the hard disk drive cable.

8
12. Insert and lock the touchpad
cable.
11. Press the upper cover onto the
assembly. Secure the cover with
seven screws.
13. Position the LCD onto the lower
assembly. Secure the hinges with
two screws at the top and two at
the rear.
14. Connect the LCD’s data and
power cables.
15. Insert the wireless LAN card and
connect the modem and antennae
cables.
16. Insert and lock the keyboard’s flex
cable. Tilt down the keyboard and
position it.

9
20. Place the hard disk drive into its
compartment and connect its data
cable. Replace its cover and
secure it with two screws.
18. Connect the speakers’ cable. Press
the cover securely into place.
19. Replace the 14 case screws.
21. Insert and lock the memory mod-
ule. Secure its cover with two
screws.
22. Slide the CD/DVD drive into its
bay.
17. Position the hinge cover. so that
you can insert and lock the cable
to the status LCD.

10
23. Lower the battery into its com-
partment and press to lock it.