Fujitsu WI610 User manual

Contents English - 1
EnglishContents
Wirelessmouse ....................................................................... 3
System requirements . . . . . ........................................................... 3
Safetyinformation ................................................................... 3
CEmarking ......................................................................... 3
Limitedworldwidewarranty .......................................................... 3
Connecting the receiver and the mouse . . . . ............................................ 4
Connecting the receiver . . . . . . ........................................................... 4
Preparing the mouse and establishing the wireless connection . ............................. 5
Usingthemouse ....................................................................... 6
Installingthesoftware ................................................................... 7
Thebuttonsonthemouse ............................................................... 8
LED ................................................................................... 9
Settingthescanningsensitivity ........................................................... 9
Switchingthemouseonandoff .......................................................... 10
Stateofchargeofthebatteryinthemouse ................................................ 10
Mobiletransport ........................................................................ 11
Using the mouse wheel .................................................................. 11
Workingenvironments ................................................................. 12
Cleaning ............................................................................... 12
Storingthebattery ...................................................................... 12
Troubleshootingandtips .............................................................. 13
The mouse is not detected or does not function . . . ........................................ 13
Connection problems with mouse . ....................................................... 13
Technicaldata ......................................................................... 14
Environmentalconditions ................................................................ 14
Fujitsu Technology Solutions 17

2 - English Contents
18 Fujitsu Technology Solutions

Wireless mouse English - 3
Wireless mouse
The wireless mouse works with digital radio technology and without the need for disruptive cables.
You can use the mouse on any computer that has a free USB port which
meets the system requirements specified below.
The sections below describe how to set up the mouse ready for use.
System requirements
• Computer with Windows 7 or Windows Vista
• At least one free USB port
• CD/DVD drive for installing the software
Safety information
Please observe the safety information supplied.
Use only type AA batteries for the mouse.
CE marking
The shipped version of this device complies with the requirements of the EC
directives 2004/108/EC "Electromagnetic compatibility", 2006/95/EC "Low
voltage directive" and 2009/125/EC "Ecodesign directive".
Limited worldwide warranty
Fujitsu Technology Solutions provides a warranty for this device. This warranty can be asserted
worldwide wherever Fujitsu Technology Solutions maintains a service office or an authorised service
partner of Fujitsu Technology Solutions is present. Such claims can be made to the extent to
which the service concerned is available in the particular country. Please contact one of our help
desks for details of the availability of the services and the response time, or visit our website at
"http://ts.fujitsu.com/service" before you make any warranty claims in the particular country.
Fujitsu Technology Solutions 19

4 - English Connecting the receiver and the mouse
Connecting the receiver and the mouse
►Switch on your PC.
Connecting the receiver
The receiver is housed directly in the mouse.
2
1
►Open the cover of the battery compartment
on the top of the mouse by pressing the
button (1) and remove the cover.
►Remove the receiver from the mouse in
the direction of the arrow (2).
►Replace the cover on the battery
compartment.
►Connect the receiver to a spare USB
port on the computer and follow the
on-screen instructions.
20 Fujitsu Technology Solutions

Connecting the receiver and the mouseEnglish - 5
Preparing the mouse and establishing the
wireless connection
Before you can use your new mouse, you must make the following preparations.
When inserting the battery, follow the safety notes and the chapter "Technical data",
Page 14 - English.UseonlyAAty
pe batteries. Switch off the mouse when it is
not used for longer periods. This extends the service life of the battery.
The mouse requires one AA battery.
1
►Open the cover of the battery compartment
on the top of the mouse by pressing the
button (1) and remove the cover.
►Insert the battery into the battery
compartment. The illustration in the battery
compartment shows how to insert the
battery in the correct orientation.
►Close the battery compartment.
OFF ON
►Set the switch on the bottom of
themouseto"On".
The wireless connection between the mouse and the receiver is established
automatically and you can start using the mouse immediately.
Fujitsu Technology Solutions 21

6 - English Using the mouse
Using the mouse
If the software is not installed, you cannot use all mouse functions.
22 Fujitsu Technology Solutions

Using the mouse English - 7
Installing the software
The supplied software must be installed in order to be able to configure the programmable
keys on the mouse and use its full range of functions.
►Insert the supplied software CD in the CD/DVD drive for the PC.
The CD will start automatically.
►If the CD does not start automatically, double click on the file Setup.exe in
the CD folder in Windows Explorer.
►Follow the instructions on the screen.
The installed software allows you to call up the following configuration menu either via the
installed programme group or via the mouse icon created in the task bar.
Fujitsu Technology Solutions 23

8 - English Using the mouse
The buttons on the mouse
5
1
4
2
3
Mouse button
Assignment without
software
Default assignment
with installed software
Optional with installed
software
Right mouse button Function as right mouse button -
Left mouse button Function as left mouse button -
DPI button Increase/decrease the resolution
(scanning sensitivity)
-
1 (centre button)Function as centre button Freely programmable
1 (centre button)
turn mouse wheel
forwards
Scroll up -
1 (centre button)
turn mouse wheel
backwards
Scroll down -
2(forwardsbutton) Depending on the active application, you can use
this button to navigate forwards or scroll forwards
Freely programmable
3 (backwards button) Depending on the active application, you
can use this button to navigate backwards
or scroll backwards
Freely programmable
4(mousew
heel
towards left)
No function (under
Windows Vista /
Windows 7: screen
content is shifted to the
left)
Screen content is
shifted to the left
Freely programmable
5 (mouse wheel
towards right)
No function (under
Windows Vista /
Windows 7: screen
content is shifted to the
right)
Screen content is
shifted to the right
Freely programmable
24 Fujitsu Technology Solutions

Using the mouse English - 9
LED
The LED provides information on the state of charge/operating status and on the scanning sensitivity.
Status indicators Description
The LED lights up red Power-on indicator
• The mouse is operative.
The LED flashes red
State of charge indicator as the mouse is being switched on
Duringtheswitch-onproc
ess of the mouse, the LED flashes depending on
the state of charge of the battery.
• The LED flashes 1x: The battery is nearly discharged.
• The LED flashes up to 5x: The battery is fully charged.
State of charge indicator in mouse operating mode
During operation, the LED flashes red if the state of charge of the battery
in the mouse becomes lower (see chapter "State of charge of the battery
in the mouse", Page 10 - English).
DPI indicator
While the resolution (DPI) is being adjusted, the LED flashes depending
on the level set (see chapter "Setting the scanning sensitivity", Page 9 -
English).
Setting the scanning sensitivity
DPI
LED
The mouse supports a resolution (scanning
sensitivity) of 1000, 1500 and 2000 dpi.
The default setting is 1500 dpi.
►To switch the scanning sensitivity from one
level to the next highest level, press the DPI
button once in each case.
After the highest level of 2000 dpi has
been reached, the next press of the DPI
button begins again with the lowest level
of 1000 dpi.
The higher the scanning sensitivity, the
faster the mouse reacts.
The LED flashes with the individual levels as follows:
• 1000 to 1500 dpi: flashes 2x red
• 1500 to 2000 dpi: flashes 3x red
• 2000 to 1000 dpi: flashes 1x red
Fujitsu Technology Solutions 25

10 - English Using the mouse
Switching the mouse on and off
If you are not intending to use the mouse for a long time, you can switch it off to save power.
Set the switch on the bottom of the mouse to "Off".
If you wish to resume work with the mouse, do not forget to switch it on again.
Stateofchargeoftheba
ttery in the mouse
Please note that the battery status indicator can no longer light if the
battery is completely discharged.
LED
If the charge of the battery in the mouse
becomes low, the LED on the mouse flashes
red.
►Replace the battery in the near future.
26 Fujitsu Technology Solutions

Using the mouse English - 11
Mobile transport
The receiver can be housed directly in the mouse.
►Slide the receiver into the opening in the
mouse casing, in the direction of the arrow.
►To remove the receiver, withdraw it
upwards with the fingers.
Using the mouse wheel
In addition to two buttons, the mouse also has a wheel that can be used as follows:
►Press the on the wheel to use the third mouse button.
►Turn the wheel forwards or backwards to scroll, for example in documents or on Internet pages.
Depending on your operating system, you may be able to move the screen content horizontally:
►Press the wheel to the left or right.
Fujitsu Technology Solutions 27

12 - English Working environments
Working environments
During signal transmission, interference can be caused by other radio
devices which use the same frequency range.
• The mouse can be used on nearly all surfaces. To ensure optimum
performance, it is recommended that the mouse be used on a relatively
light-coloured but non-reflective surface.
• The mouse switches to energy-saving mode if it is not used for a certain period of time.
Move the mouse or press one of the mouse buttons to "wake up" the mouse again.
Cleaning
Switch off all equipment concerned.
Do not use any cleaning agents that contain abrasives or which may dissolve plastic.
Ensure that no liquid enters the inside of the device.
The casing surfaces may be cleaned with a dry cloth. If particularly dirty, use a cloth
that has been moistened in mild domestic detergent and then carefully wrung out,
you can also clean the keyboard using disinfectant wipes.
Storing the battery
Ifyoudonotwa
nt to use your mouse for a considerable period of time, remove the
battery and store it in a dry place at room temperature.
28 Fujitsu Technology Solutions

Troubleshooting and tips English - 13
Troubleshooting and tips
If a fault occurs, try to eliminate it with the measures described in this chapter.
If you cannot resolve the fault, contact your local sales office or computer dealer.
If you need to exchange the device, please note that you must return it to your dealer
in its original packaging and also a produce proof of purchase (receipt). Keep your
receipt and the original packaging in a safe place after purchase.
The mouse is not detected or does not function
►Check that the mouse is switched on (on/off switch on bottom of mouse)
►Check that the mouse battery is properly inserted.
►Disconnect the receiver from the computer and reconnect it.
►If the table top is made of glass or of a reflective material, this can interfere with the mouse
sensor. In this case use an ordinary mouse pad or move to a more favourable desk.
►The receiver may be too far from the mouse.
►Check whether the USB port on your computer is correctly configured.
►Restart your computer.
Connection problems with mouse
The connection can be disturbed by other radio devices in the surrounding
area that use the same radio frequency.
►Insert the receiver into another USB port of your computer.
On systems with a USB 3.0 port, connection problems may occur
because of technical reasons.
►Do not connect the receiver to a USB port which is very close to a USB 3.0 port which has
a USB 3.0 end device connected (e.g. immediately adjacent USB ports).
►Where appropriate, use a USB extension cable to increase the separation.
Fujitsu Technology Solutions 29

14 - English Technical data
Technical data
Safety regulations complied with EN 60950
Interface Compatible with USB 2.0 and 1.1
Frequency band 2.4 GHz
Modulation GFSK
Number of channels 77
Report rate max. 125
Mouse
• Power supply
• Current consumption (on white
paper)
•Batterylife
• Resolution
• 1x AA alkaline battery, 1,5 V
• Active mode: 7,5 mA,
sleep mode: 2,29 mA - 0,11 mA
• about 6 months for normal office use
• 1000 dpi / 1500 dpi / 2000 dpi
(selectable via the DPI button of the mouse)
Receiver
• Power supply
• Power consumption
• USB mode: 5 V
• Active mode: < 40 mA, sleep mode: 2,5 mA
Environmental conditions
Operating temperature 0 °C – 40 °C
Mouse/Keyboard range Up to 10 m (depending on ambient interference)
30 Fujitsu Technology Solutions

Federal Communications Commission (FCC) Notice:
Changes or modifications not expressly approved by the party
responsible for compliance could void the user's authority to operate the equipment
NOTE: THE MANUFACTURER IS NOT RESPONSIBLE FOR ANY RADIO OR TV INTERFERENCE
CAUSED BY UNAUTHORIZED MODIFICATIONS TO THIS EQUIPMENT. SUCH MODIFICATIONS
COULD VOID THE USER’S AUTHORITY TO OPERATE THE EQUIPMENT.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates, uses
and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by one or more of the
following measures:
-- Reorient or relocate the receiving antenna.
-- Increase the separation between the equipment and receiver.
-- Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected.
-- Consult the dealer or an experienced radio/TV technician for help.
This device complies with Part 15 of the FCC Rules. Operation
is subject to the following two conditions: (1) this device may not cause harmful interference, and (2)
this device must accept any interference received, including interference that may cause undesired
operation.
FCC Notice English-13
Fujitsu Technology Solutions 31