funtec 112001 User manual

USER MANUAL
ID: 112001
BEACHSPORT FOLDING
GOALS 3 x 2 m

2
ID: 112001
BEACHSPORT FOLDING
GOALS 3 x 2 m

3
ID: 112001
PARTS
Index Description ID Qu (for 1 pair of goals)
1Goal post, left 112-001-L 2 pcs (1 pc/goal)
2Goal post, right 112-001-R 2 pcs (1 pc/goal)
3Rear net holder, left 112-201-L 2 pcs (1 pc/goal)
4Rear net holder, right 112-201-R 2 pcs (1 pc/goal)
5Goal frame crossbar 112-001-2940 2 pcs (1 pc/goal)
6Floor bar 112-204 2 pcs (1 pc/goal)
7Aluminium profi le insert, rectangular, short 112-361-1790 4 pcs (2 pcs/goal)
8Aluminium profi le insert, rectangular, long 112-361-2590 2 pcs (1 pc/goal)
9Aluminium profi le insert, L-shaped 112-360-97 56 pcs (28 pcs/goal)
10 Self-drilling panhead screw, 3,9 x 32 mm 112-311 14 pcs (7 pcs/goal)
11 Countersunk screw, M6 x 14 mm 112-300 8 pcs (4 pcs/goal)
12 Cap nut, self-locking, M6 112-320 8 pcs (4 pcs/goal)
13 Panhead screw, M8 x 50 mm 112-310 8 pcs (4 pcs/goal)
14 Cap nut, self-locking, M8 112-321 8 pcs (4 pcs/goal)
15 Countersunk screw, M10 x 55 mm 112-302 8 pcs (4 pcs/goal)
16 Cap nut, self-locking, M10 112-322 8 pcs (4 pcs/goal)
17 Counterunk screw, M6 x 80 mm 112-301 8 pcs (4 pcs/goal)
18 Aluminium L-profi le, short 112-350 8 pcs (4 pcs/goal)
19 Aluminium L-profi le, long 112-351 8 pcs (4 pcs/goal)
20 Pipe folding pin 111406 8 pcs (4 pcs/goal)

4
PRE-ASSEMBLY
ID: 112001
Security advice
- This product has been developed for use in leisure sports
and at competitions
- This product must be used in accordance with its designa-
ted use which is Beachsoccer and Beachhandball.
- We strongly recommend installing an anti-tilt device to the
fl oor ground frame during use.
- Before using this product make sure that all components
and connecting bolts are safely installed and tightened.
Assembly Instructions
- This product has to be assembled with due care by two
adult persons.
- For this product a level ground is required with the dimensi-
ons of at least 5 x 5 m.
We recommend using a soft underlay to prevent damage to
the painted parts of the goal frame.
- Please take no unneccessary risks while handling the
equipment and be careful when assembling this product.
Maintenance and care
- This product does not require regular maintenance work,
However, please check all components and connecting bolts
are intact and safely tightened before use, at least once
a year. Any damaged parts should be replaced as soon as
possible.
- To clean this product, use water and soap avoiding all types
of solvents or alcohol. Do not use dirty or abrasive cloths.
- Store in a dry place, ideally at a temperature of
5° C to 25° C.
Please team up with a second person. Do not set up alone.

5
ACCESSORIES
Recommended Accessories:
ID: 112008 - 1 pair of 3 x 2 m goal nets
Goal nets for Beachsport folding goals (1 pair)
4 mm netting material, mesh size: 10 cm, suitable for 3 x 2 m
goals, colour: yellow, net depth size at top/bottom:
120 cm/120 cm
ID: 112002 - 1 pair of ground fi xings for 2 goals
Ground fi xings for freestanding goal frames (anti-tilt device),
for 1 pair of goals, each fi xing includes two sand anchors and
a black isilink cord

6
ASSEMBLY
Hex key,
sizes 4, 5 and 6
Wrench,
sizes 10, 13 and 17
Phillips head
screwdriver
Plastic hammer
Required for assembly:
456
10 mm / 13 mm / 17 mm

7
ASSEMBLY

8
ASSEMBLY
Tighten only slightly.
Tighten only slightly.

9
ASSEMBLY

10
GOAL NET INSTALLATION