Furrion FACW10ESSA-BL User manual

This quick start guide will help you install and use the
device properly. Forfurther support please visit
www.furrion.com/support.
PRODUCT OVERVIEW
Press to increase the
temperature set-point Press to decrease
temperature set-point
Press to change
the fan speed
Press once to turn on.
Press repeatedly to
select mode
Operation Mode
Fan Speed
Room Temperature or
Error Code
WHAT’S IN THE BOX
Warranty Manual
Warning Card
Quick Start Guide
Warranty Manual
Warning Card
Quick Start Guide
Thermostat x 1
QSG x 1
Warranty Manual x 1
NOTE: Product design and packaging may change without
notice.
INSTALLATION
WARNING: Risk of electric shock. Always verify that the
electrical power to the circuit has been disconnected
before performing the installation procedures.
Thermostat Location
This thermostat is a regulating device which senses the
room real-time temperature and performs actions to
maintain the temperature near a desired set-point. For
accurate temperature control, the following considerations
should be taken into account:
1. Mount the thermostat on an interior wall, approximately
5 ft. (1.5m) above the floor. Install in a location with good
air circulation and avoid damp areas.
2. Avoid to install the thermostat in areas that are
exposed to temperature variances, such as direct
sunlight, near windows and doors, above or below
supply vents. Do not install the thermostat in locations
near heat sources like televisions, lamps, or fireplaces.
Wiring and Mounting the Thermostat
1. Rotate the thermostat cover counterclockwise and pull
out the base plate.
2. Use the base plate as a template and drill a hole on
the vehicle wall. Extend the four wire cables from the
cutout area. Refer to the cable tag label for each cable
definition.
3. Mount the thermostat base on the wall using screws
included with the thermostat.
NOTE: Make sure the base is not covering the hole and
squeezing the thermostat cables. Take care in case of
damaging the temperature sensor.
4. Connect the cables to thermostat.
5. Replace the thermostat to the base and rotate
clockwise until it snaps into place.
Thermostat Cables
Thermostat Cables
Thermostat
cables
2
34
5
2
43
5
1
STANDARD SINGLE ZONE
WALL THERMOSTAT
MODEL: FACWESSABL
QUICK START GUIDE
For further support and to download the air
conditioner user manual please scan the QR
code or visit: https://furrion.com/pages/
downloads-climate

See the “DIP Switch Settings” section in your air
conditioner instruction manual. Only activate the heat
mode(s) for the zone controller intended to operate the
heating function.
Set the Temperature
The temperature set-point ranges from 60°F~86°F
(16°C~30°C).
1. Press the button to switch to desired mode.
2. Press or button to increase or decrease the
temperature set-point to your comfort level.
NOTE: The temperature set-point is not available in FAN mode.
Set the Fan Speed
1. Press the button to switch to your desired mode.
2. Press the FAN button to select the fan speed. The
available fan setting under each mode are as following:
Mode Fan Speed
Cool Low/High/Auto
Heat Low/High/Auto/Off
Fan Low/High
Dry /
When Auto mode is selected, the fan will operate in High or Low
speed automatically by detecting the temperature difference
between the set-point and the room. When the set-point
temperature is reached, the fan will turn off after 30 seconds.
LCD ERROR CODE
The following error code will be displayed on the LCD when
the system detects one of the following faults has occurred.
LCD Error Code
E1 Control box indoor temperature sensor out of order.
System will shut down.
E2 Evaporator temperature sensor out of order. System will
shut down.
E3 Loss of communication between the thermostat and
control box. System will shut down.
E6 Thermostat indoor temperature sensor out of order.
System will shut down.
lo Insufficient low level of +12V power supply. System will
shut down.
SPECIFICATIONS
DC Input Power DC 12V
Power Consumption <0.5W
Baud Rate 9600bps
Dimension 3 x 3 x ⁄” (75 x 75 x 22.5mm)
Weight 2.12oz. / 60g
LCD Viewing angle 12 o’clock
OPERATION
Your Furrion wall thermostat has been preprogrammed
with factory default settings. Review the settings below and
adjust to your comfort level.
Factory Settings
Heating 68°F / 20°C
Cooling 72°F / 22°C
Fan Speed AUTO
Mode COOL
Turn On/Off the Thermostat
To turn on, press and hold the button for 3 seconds to
turn on the thermostat. To turn off, press and hold button
for 3 seconds to turn off the thermostat.
Change the Temperature Format
Press both the or buttons for 3 seconds to toggle the
temperature format between Centigrade and Fahrenheit.
NOTE: °F indicates Fahrenheit and °C indicates
Centigrade.
Change the Operating Mode
After the thermostat has been turned on, press the
button to toggle through COOL, HEAT, FAN and DRY
modes. The activated mode icon and temperature set-point
will be displayed on the LCD. The mode will be selected
automatically after 2 seconds without any operation.
NOTE: If connected to a Furrion multi-zone control box
(FACC12ZA-BL or FACC12HA-BL), the furnace and/or
heatstrip DIP switches in the air conditioner control box
must be enabled:
–Furnace ON, Heatstrip OFF - Furnace heat only, HEAT
Fwill be displayed on LCD after selected.
–Heatstrip ON, Furnace OFF - Heatstrip heat only, HEAT
Hwill be displayed on LCD after selected.
–Furnace ON, Heatstrip ON - Furnace and heatstrip
heat, default is furnace heat mode (HEAT F), press the
button to switch to heatstrip heat mode (HEAT H).
–Furnace OFF, Heatstrip OFF - The heat mode is
disabled.
Furrion Innovation Center & Institute of Technology
●52567 Independence Ct., Elkhart, IN 46514, USA
●Toll free:1-800-789-3341 ●Email: [e-mail]
©2007-2021 Furrion Ltd. Furrion® and the Furrion logo are trademarks
licensed for use by Furrion Ltd. and registered in the U.S. and other
countries.
For Patent Info: www.furrion.com/pages/patents
FURRION.COM
IG-FHA00033 V1.0