Furrion FACW10SA-BL User manual

This quick start guide will help you install and use the device
properly. Forfurther support please visit www.furrion.com/
support.
PRODUCT OVERVIEW
Press to increase the
temperature set-point Press to decrease
temperature set-point
Press to change
the fan speed
Press once to turn on.
Press repeatedly to
select mode
Operation Mode
Fan Speed
Room Temperature or
Error Code
WHAT’S IN THE BOX
Warranty Manual
Warning Card
Quick Start Guide
Warranty Manual
Warning Card
Quick Start Guide
Thermostat x 1
QSG x 1
Warranty Manual x 1
NOTE: Product design and packaging may change without
notice.
INSTALLATION
1. Rotate the thermostat cover counterclockwise and pull out
the base plate.
2. Use the base plate as a template and drill a hole on the
vehicle wall. Extend the four wire cables from the cutout area.
Refer to the cable tag label for each cable definition.
3. Fix the base plate on the wall using 2 self-tapping screws.
NOTE: Make sure the base plate is not covering the hole and
squeezing the thermostat cables.
4. Connect the cables to thermostat.
5. Replace the thermostat to the base plate and rotate
clockwise until it clips into place.
Thermostat Cables
Thermostat Cables
Thermostat
cables
2
34
5
2
34
5
1
Standard Single
Zone Thermostat
Quick Start Guide
Model: FACW10SA-BL
OPERATION
Your Furrion wall thermostat has been preprogrammed with
factory default settings. Review the settings below and adjust to
your comfort level.
Factory Settings
Heating 68°F / 20°C
Cooling 72°F / 22°C
Fan Speed AUTO
Mode COOL
TURN ON/OFF THE THERMOSTAT
To turn on, press and hold the button for 3 seconds to turn on the
thermostat. To turn off, press and hold button for 3 seconds to
turn off the thermostat.
CHANGE THE TEMPERATURE FORMAT
Press both the or buttons for 3 seconds to toggle the
temperature format between Centigrade and Fahrenheit.
NOTE: °F indicates Fahrenheit and °C indicates Centigrade.
CHANGE THE OPERATING MODE
After the thermostat is turn on, press the button repeatedly
to toggle through the COOL, HEAT, FAN and DRY modes. The
activated mode icon and temperature set-point will be displayed on
the LCD. The thermostat will transmit the last selected operation
mode command to the control box after 2 seconds without any
operation.
NOTE: If connected to a Furrion multi-zone control box
(FACC12NA-BL), the furnace and/or heatstrip DIP switches in
the control box must be enabled to activate the following HEAT
mode(s):
●Furnace ON, Heatstrip OFF - Furnace heat only, HEAT F will be
displayed on LCD after selected.

●Heatstrip ON, Furnace OFF - Heatstrip heat only, HEAT H will be
displayed on LCD after selected.
●Furnace ON, Heatstrip ON - Furnace and heatstrip heat, defalut
is furnace heat mode (HEAT F), press the button to toggle
to heatstrip heat mode (HEAT H).
●Furnace OFF, Heatstrip OFF - The heat mode is disabled.
See the “DIP Switch Settings” section in your air conditioner
instruction manual. Only activate the heat mode(s) for the zone
controller intended to operate the heating function.
SET THE TEMPERATURE
The temperature set-point ranges from 60°F~86°F (16°C~30°C).
1. Press button to toggle to your desired mode.
2. Press or button to increase or decrease the
temperature set-point to your comfort level.
NOTE: The temperature set-point is not available in FAN mode.
SET THE FAN SPEED
1. Press the button to toggle to your desired mode.
2. Press the FAN button to select fan speed. The available fan
setting under each mode are as following:
Mode Fan Speed
COOL LOW/HIGH/AUTO
HEAT LOW/HIGH/AUTO/OFF
FAN LOW/HIGH
DRY /
When the AUTO fan mode is selected, the fan will operate in
HIGH or LOW speed automatically by detecting the temperature
difference between the set-point and the room. When the set point
temperature is reached, the fan will turn off after 30 seconds.
NOTE: The fan speed selection is not available in DRY mode.
Furrion Innovation Center & Institute of Technology
●52567 Independence Ct., Elkhart, IN 46514, USA
●Toll free:1-800-789-3341 ●Email: [email protected]
©2007-2020 Furrion Ltd. Furrion® and the Furrion logo are trademarks
licensed for use by Furrion Ltd. and registered in the U.S. and other
countries.
Furrion.com
IG-FHA00031 V1.0
LCD ERROR CODE
The following error code will be displayed on the LCD when the
system detects one of the following faults has occurred.
LCD Error Code
E1 Indoor temperature sensor out of order. System will
shut down.
E2 Evaporator temperature sensor out of order. System
will shut down.
E3 Loss of communication between the thermostat and
control box. System will shut down.
lo Insufficient low level of +12V power supply. System will
shut down.
SPECIFICATIONS
DC Input Power DC 12V
Power Consumption <0.5W
Baud Rate 9600bps
Dimension 3 x 3 x 15/16” (75 x 75 x 22.5mm)
Weight 0.06kg
LCD Viewing angle 12 o’clock