Furzone 40800 User manual
40800
POWER BANK
Charging the Battery Pack
● Always charge the Battery Pack indoor under environment temperature: 0~35℃,
relative humidity: 65±20%. Never charge it the rain or in wet conditions.
● Charge for 4 hours at least before you use the Lithium Battery Pack for the first time.
If you do not charge it before using it, the battery pack’s charging capacity may decrease.
● Put mains wall socket and plug charger adapter into socket.
● Switch battery pack to on position.
● Switch off wall socket and disconnect battery pack and charger adapter.
● Do not leave the battery pack overnight on charge.
Battery Pack Operation
● Switch clipper and battery pack off .
● Push connector from clipper to battery pack socket.
● Ensure blades are secure, lightly tensioned and oiled.
● Ensure air vents are free of hair.
● Switch battery pack on.
● Switch clipper on, adjust tension and clip.
Maintenance
●Always fully charge the battery after clipping, or prior to storing the battery pack for
longer periods of time.
●When not in use, it is recommended to charge the battery at least every 6 months.
●While using the battery, stay away from heat source and high pressure, don't let children
play the battery. Do not drop or beat the Battery Packs.
●Store the battery pack in a warm and dry location at a temperature between 5℃ to 35℃.
●Never Attempt to alter or open the Battery Pack or Charger. There are no customer
serviceable parts inside.
●Do not regularly use the battery pack for a few minutes at a time.
• Before use , please carefully read the user manual and outer label of the battery.
TROUBLESHOOTING (BATTERY PACK)
Failure
No Power
Battery pack low
No power after
charging
Cause Action
Check start button has been depressed
Charge battery pack
Discharge battery fully by running clipper.
Until it stops. Do not attach blades during
this operation. Allow 15 minutes to cool
battery pack. Charge battery pack for 4
hours and try again. If battery is low, repeat
the above once or twice.
LED Indicator Lights
Push the “on” button switch, LED display remaining power.
The blue LED light will turn on when the mains adaptor in plugged into the
battery pack socket, and the battery pack is in the “on” position.
Slow flashing LED light: while in charging.
Soild Blue light: Indicated that the unit is full charged.
TECHNICAL SPECIFICATION BATTERY PACK CHARGING
BATTERY PACK OPERATION
To charge the battery pack plug the
mains charging cable cable into the
socket marked DV IN 9V-12V/3A.
The blue battery capacity LED
indicator lights will increase
as the battery charges and
decrease as battery discharges
(100%,75%,40%,10%)
1. Before plugging the clipper into the battery pack.
It is important to connect the correct clipper lead to the
correct power output point on the battery pack.
Note: Use only the adapter supplied for charging the battery pack.
Do not use any other charger.
3. Switch on clipper. If you do not switch on the clipper the battery pack will
automatically switch itself off after approximately 6 seconds.
Note: 614D and 610D clippers cannot be operated at the same time.
Always replace the rubber caps when the socket/s are not in use.
2. Start the battery pack by pressing
the start button here.
Capacity
Running Time
Charging Input
Cells
Power Display
Dimensions
Weight
12000 mAh
12V/2A: 7.5 - 9 hours (e.g. when using 610D clipper)
15V/4A: 4 - 5 hours (e.g. when using 614D clipper)
12 volts 3 Amps
Li-ion Rechargeable Battery
4 x LED lights indicating power levels (100%,75%,40%,10%)
LxWxH: 150x75x42mm / 150x75x60mm (incl. clip)
550g
610D clipper 614D clipper
For the 610D connect the clipper
lead to the 12V socket and slide
the switch to the left hand
position of DC OUT 12V/2A.
For the 614D connect the clipper
lead to the 15V socket and slide
the switch to the left hand
position of DC OUT 15V/3A.
