Fusic FD-110 User manual
FD-110 Installation
Service
Help
Service Help
WWW.FYSIC.NL
NL 073 7506 291
(Lokaal tarief)
BE 03 238 5666
(Lokaal tarief)
(Tarif local)
DE 0180 503 0085
Lokale Festnetzkosten
Hesdo, Australiëlaan 1
5232 BB, ‘s-Hertogenbosch
The Netherlands
WWW.FYSIC.NL
NL 073 7506 291
BE 03 238 5666
DE 0180 503 0085
Hesdo, Australiëlaan 1, 5232 BB,
‘s-Hertogenbosch, The Netherlands
(Lokaal tarief)
(Tarif local)
(Lokaal tarief)
(Lokale Festnetzkosten)
Outdoor-unit:
Indoor-unit:
Important Note:
●If you do not plan to use the device for a long time, such as at a vacation, please remove the
battery from Transmitter, then put them in a safe place.
●Improperly using a battery may cause it to leak and damage nearby items, and can create the
risk of fire and personal injury. Batteries should not be left in an area where the children can
reach them as they may pose a chocking hazard.
●Recycle used batteries following environmental protection practices.
Transmitter Installation:
●Stick the Transmitter on the wall or the door with
double-sided adhesive tape.
Receiver Installation:
●Plug the Receiver into any socket of AC110~240V power.
2
Battery Installation (Transmitter):
Transmitter uses a 3V CR2032 battery (included).
Open the Transmitter (by pushing in the interface located at the bottom with a flat screw driver)
and place the battery. Please be well noted with the correct battery polarity.To replace a new
battery, operate in the same way.
Press lightly the battery
holder at side
CR2032 3V Lithium Battery
Important Note:
●If you do not plan to use the device for a long time, such as at a vacation, please remove the
battery from Transmitter, then put them in a safe place.
●Improperly using a battery may cause it to leak and damage nearby items, and can create the
risk of fire and personal injury. Batteries should not be left in an area where the children can
reach them as they may pose a chocking hazard.
●Recycle used batteries following environmental protection practices.
Transmitter Installation:
●Stick the Transmitter on the wall or the door with
double-sided adhesive tape.
Receiver Installation:
●Plug the Receiver into any socket of AC110~240V power.
2
Battery Installation (Transmitter):
Transmitter uses a 3V CR2032 battery (included).
Open the Transmitter (by pushing in the interface located at the bottom with a flat screw driver)
and place the battery. Please be well noted with the correct battery polarity.To replace a new
battery, operate in the same way.
Press lightly the battery
holder at side
CR2032 3V Lithium Battery
Connecting:
Important Note:
●If you do not plan to use the device for a long time, such as at a vacation, please remove the
battery from Transmitter, then put them in a safe place.
●Improperly using a battery may cause it to leak and damage nearby items, and can create the
risk of fire and personal injury. Batteries should not be left in an area where the children can
reach them as they may pose a chocking hazard.
●Recycle used batteries following environmental protection practices.
Transmitter Installation:
●Stick the Transmitter on the wall or the door with
double-sided adhesive tape.
Receiver Installation:
●Plug the Receiver into any socket of AC110~240V power.
2
Battery Installation (Transmitter):
Transmitter uses a 3V CR2032 battery (included).
Open the Transmitter (by pushing in the interface located at the bottom with a flat screw driver)
and place the battery. Please be well noted with the correct battery polarity.To replace a new
battery, operate in the same way.
Press lightly the battery
holder at side
CR2032 3V Lithium Battery
1
Accessories List:
●1 x Receiver ●1 x Transmitter
●1 x User Manual ●1 x Double-sided adhesive
●1 x 3 volts CR2032 battery for transmitter
Technical Specification:
●Frequency: 433.92MHz+100KHz
●Modulation Type: ASK
●Ring Volume:＞85dB(within 0.5m)
●Channel space: 1 million sets of auto-learning codes
●Receiver bandwidth: ±90KHz
●Reception Sensitivity:＞-105dBm
●Transmitter Power:＜10mW
●Power consumption(Receiver): standby:＜0.3W
●Power consumption(Transmitter): standby:＜5uA working:＜10mA
●Power Supply(Receiver): AC110-240V
●Power Supply(Transmitter): DC 3V (1x CR2032)
●Operating Range:＞150m (in the open air)
Names for Parts:
Instruction Manual
Auto-leaning Code Wireless Door Chime
Model No.: QH-861AK
VOL
MODE
CODE
Important Note:
●If you do not plan to use the device for a long time, such as at a vacation, please remove the
battery from Transmitter, then put them in a safe place.
●Improperly using a battery may cause it to leak and damage nearby items, and can create the
risk of fire and personal injury. Batteries should not be left in an area where the children can
reach them as they may pose a chocking hazard.
●Recycle used batteries following environmental protection practices.
Transmitter Installation:
●Stick the Transmitter on the wall or the door with
double-sided adhesive tape.
Receiver Installation:
●Plug the Receiver into any socket of AC110~240V power.
2
Battery Installation (Transmitter):
Transmitter uses a 3V CR2032 battery (included).
Open the Transmitter (by pushing in the interface located at the bottom with a flat screw driver)
and place the battery. Please be well noted with the correct battery polarity.To replace a new
battery, operate in the same way.
Press lightly the battery
holder at side
CR2032 3V Lithium Battery
1x1x
1x
<10 sec.
Important Note:
●If you do not plan to use the device for a long time, such as at a vacation, please remove the
battery from Transmitter, then put them in a safe place.
●Improperly using a battery may cause it to leak and damage nearby items, and can create the
risk of fire and personal injury. Batteries should not be left in an area where the children can
reach them as they may pose a chocking hazard.
●Recycle used batteries following environmental protection practices.
Transmitter Installation:
●Stick the Transmitter on the wall or the door with
double-sided adhesive tape.
Receiver Installation:
●Plug the Receiver into any socket of AC110~240V power.
2
Battery Installation (Transmitter):
Transmitter uses a 3V CR2032 battery (included).
Open the Transmitter (by pushing in the interface located at the bottom with a flat screw driver)
and place the battery. Please be well noted with the correct battery polarity.To replace a new
battery, operate in the same way.
Press lightly the battery
holder at side
CR2032 3V Lithium Battery
Important Note:
●If you do not plan to use the device for a long time, such as at a vacation, please remove the
battery from Transmitter, then put them in a safe place.
●Improperly using a battery may cause it to leak and damage nearby items, and can create the
risk of fire and personal injury. Batteries should not be left in an area where the children can
reach them as they may pose a chocking hazard.
●Recycle used batteries following environmental protection practices.
Transmitter Installation:
●Stick the Transmitter on the wall or the door with
double-sided adhesive tape.
Receiver Installation:
●Plug the Receiver into any socket of AC110~240V power.
2
Battery Installation (Transmitter):
Transmitter uses a 3V CR2032 battery (included).
Open the Transmitter (by pushing in the interface located at the bottom with a flat screw driver)
and place the battery. Please be well noted with the correct battery polarity.To replace a new
battery, operate in the same way.
Press lightly the battery
holder at side
CR2032 3V Lithium Battery
1
Accessories List:
●1 x Receiver ●1 x Transmitter
●1 x User Manual ●1 x Double-sided adhesive
●1 x 3 volts CR2032 battery for transmitter
Technical Specification:
●Frequency: 433.92MHz+100KHz
●Modulation Type: ASK
●Ring Volume:＞85dB(within 0.5m)
●Channel space: 1 million sets of auto-learning codes
●Receiver bandwidth: ±90KHz
●Reception Sensitivity:＞-105dBm
●Transmitter Power:＜10mW
●Power consumption(Receiver): standby:＜0.3W
●Power consumption(Transmitter): standby:＜5uA working:＜10mA
●Power Supply(Receiver): AC110-240V
●Power Supply(Transmitter): DC 3V (1x CR2032)
●Operating Range:＞150m (in the open air)
Names for Parts:
Instruction Manual
Auto-leaning Code Wireless Door Chime
Model No.: QH-861AK
VOL
MODE
CODE
1x
v1.2
Service
Help
Service Help
WWW.FYSIC.NL
NL 073 7506 291
(Lokaal tarief)
BE 03 238 5666
(Lokaal tarief)
(Tarif local)
DE 0180 503 0085
Lokale Festnetzkosten
Hesdo, Australiëlaan 1
5232 BB, ‘s-Hertogenbosch
The Netherlands
WWW.FYSIC.NL
NL 073 7506 291
BE 03 238 5666
DE 0180 503 0085
Hesdo, Australiëlaan 1, 5232 BB,
‘s-Hertogenbosch, The Netherlands
(Lokaal tarief)
(Tarif local)
(Lokaal tarief)
(Lokale Festnetzkosten)
Frequency: 433MHz ASK
Transmission power: <10mW
EU-CONFORMITEITSVERKLARING
Hierbij verklaar ik, Hesdo, dat het type radioapparatuur FD-110 conform is met Richtlijn 2014/53/EU.
De volledige tekst van de EU-conformiteitsverklaring kan worden geraadpleegd op het volgende
internetadres: http://DOC.hesdo.com/FD-110-DOC.pdf
DECLARATION DE CONFORMITE
Le soussigné, Hesdo, déclare que l’équipement radioélectrique du type FD-110 est conforme à la directive
2014/53/UE. Le texte complet de la déclaration UE de conformité est disponible à l’adresse internet suivante:
http://DOC.hesdo.com/FD-110-DOC.pdf
ÜBEREINSTIMMUNGSERKLÄRUNG
Hiermit erklärt Hesdo, dass der Funkanlagentyp FD-110 der Richtlinie 2014/53/EU entspricht.
Der vollständige Text der EU-Konformitätserklärung ist unter der folgenden Internetadresse verfügbar:
http://DOC.hesdo.com/FD-110-DOC.pdf
EU DECLARATION OF CONFORMITY
Hereby, Hesdo declares that the radio equipment type FD-110 is in compliance with Directive 2014/53/EU.
The full text of the EU declaration of conformity is available at the following internet address:
http://DOC.hesdo.com/FD-110-DOC.pdf
Change melody:
Unregister:
melody-1
~
melody-36 Volume 1...6
Lamp / Ring / Lamp & Ring:
1
Accessories List:
●1 x Receiver ●1 x Transmitter
●1 x User Manual ●1 x Double-sided adhesive
●1 x 3 volts CR2032 battery for transmitter
Technical Specification:
●Frequency: 433.92MHz+100KHz
●Modulation Type: ASK
●Ring Volume:＞85dB(within 0.5m)
●Channel space: 1 million sets of auto-learning codes
●Receiver bandwidth: ±90KHz
●Reception Sensitivity:＞-105dBm
●Transmitter Power:＜10mW
●Power consumption(Receiver): standby:＜0.3W
●Power consumption(Transmitter): standby:＜5uA working:＜10mA
●Power Supply(Receiver): AC110-240V
●Power Supply(Transmitter): DC 3V (1x CR2032)
●Operating Range:＞150m (in the open air)
Names for Parts:
Instruction Manual
Auto-leaning Code Wireless Door Chime
Model No.: QH-861AK
VOL
MODE
CODE
1x
1
Accessories List:
●1 x Receiver ●1 x Transmitter
●1 x User Manual ●1 x Double-sided adhesive
●1 x 3 volts CR2032 battery for transmitter
Technical Specification:
●Frequency: 433.92MHz+100KHz
●Modulation Type: ASK
●Ring Volume:＞85dB(within 0.5m)
●Channel space: 1 million sets of auto-learning codes
●Receiver bandwidth: ±90KHz
●Reception Sensitivity:＞-105dBm
●Transmitter Power:＜10mW
●Power consumption(Receiver): standby:＜0.3W
●Power consumption(Transmitter): standby:＜5uA working:＜10mA
●Power Supply(Receiver): AC110-240V
●Power Supply(Transmitter): DC 3V (1x CR2032)
●Operating Range:＞150m (in the open air)
Names for Parts:
Instruction Manual
Auto-leaning Code Wireless Door Chime
Model No.: QH-861AK
VOL
MODE
CODE
1x
1
Accessories List:
●1 x Receiver ●1 x Transmitter
●1 x User Manual ●1 x Double-sided adhesive
●1 x 3 volts CR2032 battery for transmitter
Technical Specification:
●Frequency: 433.92MHz+100KHz
●Modulation Type: ASK
●Ring Volume:＞85dB(within 0.5m)
●Channel space: 1 million sets of auto-learning codes
●Receiver bandwidth: ±90KHz
●Reception Sensitivity:＞-105dBm
●Transmitter Power:＜10mW
●Power consumption(Receiver): standby:＜0.3W
●Power consumption(Transmitter): standby:＜5uA working:＜10mA
●Power Supply(Receiver): AC110-240V
●Power Supply(Transmitter): DC 3V (1x CR2032)
●Operating Range:＞150m (in the open air)
Names for Parts:
Instruction Manual
Auto-leaning Code Wireless Door Chime
Model No.: QH-861AK
VOL
MODE
CODE
1x
1
Accessories List:
●1 x Receiver ●1 x Transmitter
●1 x User Manual ●1 x Double-sided adhesive
●1 x 3 volts CR2032 battery for transmitter
Technical Specification:
●Frequency: 433.92MHz+100KHz
●Modulation Type: ASK
●Ring Volume:＞85dB(within 0.5m)
●Channel space: 1 million sets of auto-learning codes
●Receiver bandwidth: ±90KHz
●Reception Sensitivity:＞-105dBm
●Transmitter Power:＜10mW
●Power consumption(Receiver): standby:＜0.3W
●Power consumption(Transmitter): standby:＜5uA working:＜10mA
●Power Supply(Receiver): AC110-240V
●Power Supply(Transmitter): DC 3V (1x CR2032)
●Operating Range:＞150m (in the open air)
Names for Parts:
Instruction Manual
Auto-leaning Code Wireless Door Chime
Model No.: QH-861AK
VOL
MODE
CODE
5 sec.
Table of contents
