FUTABA CIU-3 User manual

USB INTERFACE
Instruction Manual
Instruction Manual
USB port
Thank you for purchasing the CIU-3.
The CIU-3 is a USB interface for communications between Link-supported devices (such as a
S.BUS servo , Gyro and ESC) and Windows computer.
Connecting and disconnecting the PC and CIU-3
1M23N31202
Notes
• Please read this manual thoroughly before using your CIU-3.
• Store this manual in a safe place where it can be accessed at any time.
Driver software and Link programs must be installed.
• For communication and setting, Link programs corresponding to each device must be installed.
Install the latest version of Link programs available on the dealer’s website because old Link
programs are incompatible with CIU-3.
Connection
*Make sure that your PC is connected the internet.
*Please update Windows before connecting the CIU-3 to the PC.
*To use the CIU-3, driver software must be installed.
*When using the CIU-3, please disconnect the other USB Serial Port
devices from the USB port on your PC.
1.Turn on the PC power.
2.Connect the CIU-3 to the USB port of the PC.
3.When the CIU-3 is first connected to the PC,
Once the CIU-3 is connected to the PC, down-
load the recommended driver software Using
Windows Vista, the "Found New Hardware
Wizard" window appears on the screen.
Click "Locate and install driver software".
Disconnection
The CIU-3 can be disconnected from PC even
while the Power is on. However, the CIU-3 should
not be disconnected while it is communicating with
a Link-supported device.
• Reproduction of all, or part, of the contents of this manual without prior written permission is prohib-
ited.
• The contents of this manual are subject to change without prior notice.
• The contents of this manual should be complete. ; Please contact us if you find errors or points that
are unclear.
• Futaba will not be responsible for the results of use of devices by the customer.
Specifications
(Specifications and ratings are subject to change without prior notice accompanying technological developments.)
• Interface: USB Rev2.0 compliant
• USB connector: USB Series A connector
• Operating voltage: 5.0V ±0.2V (USB bus power)
• Current drain
(At connection, idle): 5.8 ±1.7mA
*The PC must have a USB port (Type A).
• Operating environment: Temperature -10 〜+45℃
• Dimensions: 18.2 x 56.5 x 9.0 mm
• Weight: 7.5g
• Applicable OS: WindowsVista/7/8/8.1/10
*A PC-LINK adapter (double
extension cord K500) is
supplied with the CIU-3.
Click

Instruction Manual
*Windows is registered trademark of Microsoft Corporation.
Connection method
1.Connect the CIU-3 to the USB port
of the PC.
2.Connect the Link-supported device
to the CIU-3.
3.Connect the batteries by referring
to the Link-supported device
instruction manual.
4.Set the power switch of the Link
device to ON.
5.Communication with the Link pro-
gram is possible.
When using the CIU-3, please disconnect the other USB Serial Port device from
the USB port on your PC.
Example of connection to Link programs supported device
(The figure below is an example of connection to an S-BUS servo.)
Usage Precautions
Do not disassemble the CIU-3. Do not open the CIU-3 case.
Opening the case may damage the PC board. In this case, PC assembly replacement or repair will become
impossible. There is also the danger of fire and electric shock.
Do not expose the CIU-3 to water or other liquids. Do not touch the CIU-3 when you hands are
wet.
Water droplets entering the CIU-3 may cause trouble. There is also the danger of fire and electric shock.
Do not drop or expose the CIU-3 to strong shock.
It may cause trouble.
Do not set anything on top of the CIU-3.
It may cause trouble.
Do not touch the connectors with your hands. Also, do not connect a dusty or dirty connector.
It may cause trouble.
Handle the PC and peripheral devices in accordance with the instruction manual and cautions
and warnings given in the instruction manual of each product.
Connect to PC USB port
PC-LINK adapter
S-BUS servo
Connect to CIU-3
Connect the batteries to
the Link-supported device
Special Markings
For safety's sake, pay special
attention whenever you see
the marks shown here.
Mark Meaning
Procedures which may lead to a dangerous condition or cause death or serious
injury to the user if not carried out properly, or procedures where the probability of
superficial injury or physical damage is high.
Procedures where the possibility of serious injury to the user is small, but there is a
danger of injury, or physical damage, if not carried out properly.
Symbol: :Prohibited
:Mandatory
<When requesting repair>
Reread manual before requesting a repair. If the problem continues, contact your local Futaba dealer. (HCA's Service
Center.)
©FUTABA CORPORATION 2016,04 (1)
FUTABA CORPORATION Phone: [phone], Facsimile: [phone]
1080 Yabutsuka, Chosei-mura, Chosei-gun, Chiba 299-4395, Japan