Future light PHS-150 User manual

©Copyright
Nachdruck verboten!
Reproduction prohibited!
Réproduction interdit!
Prohibida toda reproducción.
Für weiteren Gebrauch aufbewahren!
Keep this manual for future needs!
Gardez ce mode d’emploi pour des
utilisations ultérieures!
Guarde este manual para posteriores usos.
BEDIENUNGSANLEITUNG
USER MANUAL
MODE D'EMPLOI
MANUAL DEL USUARIO
PHS-150
Moving-Head

51838155_V_1_1.DOC
2/104
MULTI-LANGUAGE-INSTRUCTIONS
Inhaltsverzeichnis
Table of contents
Sommaire
Contenido
EINFÜHRUNG................................................................................................................................................... 4
SICHERHEITSHINWEISE................................................................................................................................. 4
BESTIMMUNGSGEMÄßE VERWENDUNG..................................................................................................... 6
GERÄTEBESCHREIBUNG .............................................................................................................................. 7
Features ......................................................................................................................................................... 7
Geräteübersicht.............................................................................................................................................. 8
INSTALLATION .............................................................................................................................................. 11
Lampeninstallation/Lampenwechsel............................................................................................................ 11
Lampenjustierung......................................................................................................................................... 12
Einsetzen/Austauschen von Gobos............................................................................................................. 12
Projektormontage......................................................................................................................................... 13
Anschluss an den DMX-512 Controller / Verbindung Projektor - Projektor................................................. 15
Anschluss ans Netz...................................................................................................................................... 16
BEDIENUNG ................................................................................................................................................... 17
Stand Alone-Betrieb..................................................................................................................................... 17
DMX-gesteuerter Betrieb ............................................................................................................................. 17
Adressierung des Projektors........................................................................................................................ 17
DMX-Protokoll .............................................................................................................................................. 18
Control Board............................................................................................................................................... 20
Hauptfunktionen........................................................................................................................................... 21
Fehlermeldungen ......................................................................................................................................... 27
REINIGUNG UND WARTUNG........................................................................................................................ 28
Sicherungswechsel ...................................................................................................................................... 28
TECHNISCHE DATEN.................................................................................................................................... 29
INTRODUCTION ............................................................................................................................................. 30
SAFETY INSTRUCTIONS .............................................................................................................................. 30
OPERATING DETERMINATIONS.................................................................................................................. 32
DESCRIPTION OF THE DEVICE ................................................................................................................... 33
Features ....................................................................................................................................................... 33
Overview ...................................................................................................................................................... 34
INSTALLATION .............................................................................................................................................. 37
Installing/Replacing the lamp ....................................................................................................................... 37
Lamp adjustment.......................................................................................................................................... 38
Inserting/Exchanging gobos......................................................................................................................... 38
Rigging ......................................................................................................................................................... 39
DMX-512 connection / connection between fixtures.................................................................................... 41
Connection with the mains........................................................................................................................... 41
OPERATION ................................................................................................................................................... 42
Stand Alone operation.................................................................................................................................. 42
DMX-controlled operation ............................................................................................................................ 42
Addressing ................................................................................................................................................... 42
DMX-protocol ............................................................................................................................................... 43
Control Board............................................................................................................................................... 45
Main functions .............................................................................................................................................. 46
Error Messages............................................................................................................................................ 52
CLEANING AND MAINTENANCE ................................................................................................................. 52
Replacing the fuse ....................................................................................................................................... 53
TECHNICAL SPECIFICATIONS..................................................................................................................... 54

51838155_V_1_1.DOC
3/104
INTRODUCTION ............................................................................................................................................. 55
INSTRUCTIONS DE SÉCURITÉ .................................................................................................................... 55
EMPLOI SELON LES PRESCRIPTIONS....................................................................................................... 57
DESCRIPTION DE L'APPAREIL.................................................................................................................... 58
Features ....................................................................................................................................................... 58
Aperçue des parties ..................................................................................................................................... 59
INSTALLATION .............................................................................................................................................. 61
Installer/Remplacer la lampe ....................................................................................................................... 61
Ajustage de la lampe.................................................................................................................................... 62
Introduire/échanger gobos ........................................................................................................................... 63
Montage du projecteur ................................................................................................................................. 63
Connexions au contrôleur DMX-512 / raccord projecteur - projecteur ........................................................ 65
Alimentation ................................................................................................................................................. 66
MANIEMENT ................................................................................................................................................... 67
Opération Stand Alone................................................................................................................................. 67
Contrôle par DMX ........................................................................................................................................ 67
Codage du projecteur................................................................................................................................... 67
Protocôle DMX............................................................................................................................................. 68
Control Board............................................................................................................................................... 70
Fonctions principales ................................................................................................................................... 71
Avis d'erreur et d'information ....................................................................................................................... 77
NETTOYAGE ET MAINTENANCE................................................................................................................. 77
Remplacer le fusible..................................................................................................................................... 78
CARACTÉRISTIQUES TECHNIQUES........................................................................................................... 79
INTRODUCCIÓN............................................................................................................................................. 80
INSTRUCCIONES DE SEGURIDAD .............................................................................................................. 80
INSTRUCCIONES DE MANEJO .................................................................................................................... 82
DESCRIPCIÓN DEL APARATO..................................................................................................................... 83
Features ....................................................................................................................................................... 83
Descripción de las partes............................................................................................................................. 84
INSTALACIÓN ................................................................................................................................................ 86
Instalar/Reemplazar la lámpara ................................................................................................................... 86
Ajuste de la lámpara .................................................................................................................................... 87
Insertar/reemplazar gobos ........................................................................................................................... 88
Montaje del proyector................................................................................................................................... 88
Conexión al controlador DMX / conexión proyector - proyector .................................................................. 90
Alimentación................................................................................................................................................. 91
OPERACIÓN ................................................................................................................................................... 91
Operación Stand Alone................................................................................................................................ 91
Control por DMX .......................................................................................................................................... 92
Direccionamiento del proyector ................................................................................................................... 92
Protócolo DMX............................................................................................................................................. 93
Control Board............................................................................................................................................... 95
Funciones principales .................................................................................................................................. 96
Avisos de error ........................................................................................................................................... 101
LIMPIEZA Y MANTENIMIENTO ................................................................................................................... 102
Reemplazar el fusible................................................................................................................................. 103
ESPECIFICACIONES TÉCNICAS................................................................................................................ 104
Das neueste Update dieser Bedienungsanleitung finden Sie im Internet unter:
You can find the latest update of this user manual in the Internet under:
Vous pouvez trouvez la dernière version de ce mode d'emploi dans l'Internet sous:
Vd. puede encontrar la versión más reciente de este manual en el Internet bajo:
www.futurelight.com

51838155_V_1_1.DOC
30/104
USER MANUAL
PHS-150
Pro-Head-Spot
CAUTION!
Keep this device away from rain and moisture!
Unplug mains lead before opening the housing!
For your own safety, please read this user manual carefully before you initial start-up.
Every person involved with the installation, operation and maintenance of this device has to
- be qualilfied
- follow the instructions of this manual
- consider this manual to be part of the total product
- keep this manual for the entire service life of the product
- pass this manual on to every further owner or user of the product
- download the ultimate version of the user manual from the Internet
INTRODUCTION
Thank you for having chosen a FUTURELIGHT PHS-150. You will see you have acquired a powerful and
versatile device.
Unpack your PHS-150.
SAFETY INSTRUCTIONS
CAUTION!
Be careful with your operations. With a dangerous voltage you can suffer a dangerous
electric shock when touching the wires!
This device has left our premises in absolutely perfect condition. In order to maintain this condition and to
ensure a safe operation, it is absolutely necessary for the user to follow the safety instructions and warning
notes written in this user manual.
Important:
Damages caused by the disregard of this user manual are not subject to warranty. The dealer
will not accept liability for any resulting defects or problems.

51838155_V_1_1.DOC
31/104
If the device has been exposed to drastic temperature fluctuation (e.g. after transportation), do not switch it
on immediately. The arising condensation water might damage your device. Leave the device switched off
until it has reached room temperature.
Please make sure that there are no obvious transport damages. Should you notice any damages on the A/C
connection cable or on the casing, do not take the device into operation and immediately consult your local
dealer.
This device falls under protection-class I. The power plug must only be plugged into a protection class I
outlet. The voltage and frequency must exactly be the same as stated on the device. Wrong voltages or
power outlets can lead to the destruction of the device and to mortal electrical shock.
Always plug in the power plug last. The power plug must always be inserted without force. Make sure that
the plug is tightly connected with the outlet.
Never let the power-cord come into contact with other cables! Handle the power-cord and all connections
with the mains with particular caution! Never touch them with wet hands, as this could lead to mortal
electrical shock.
Never modify, bend, strain mechanically, put pressure on, pull or heat up the power cord. Never operate next
to sources of heat or cold. Disregard can lead to power cord damages, fire or mortal electrical shock.
The cable insert or the female part in the device must never be strained. There must always be sufficient
cable to the device. Otherwise, the cable may be damaged which may lead to mortal damage.
Make sure that the power-cord is never crimped or damaged by sharp edges. Check the device and the
power-cord from time to time.
If extension cords are used, make sure that the core diameter is sufficient for the required power
consumption of the device. All warnings concerning the power cords are also valid for possible extension
cords.
Always disconnect from the mains, when the device is not in use or before cleaning it. Only handle the
power-cord by the plug. Never pull out the plug by tugging the power-cord. Otherwise, the cable or plug can
be damaged leading to mortal electrical shock. If the power plug or the power switch is not accessible, the
device must be disconnected via the mains.
If the power plug or the device is dusty, the device must be taken out of operation, disconnected and then be
cleaned with a dry cloth. Dust can reduce the insulation which may lead to mortal electrical shock. More
severe dirt in and at the device should only be removed by a specialist.
There must never enter any liquid into power outlets, extension cords or any holes in the housing of the
device. If you suppose that also a minimal amount of liquid may have entered the device, it must immediately
be disconnected. This is also valid, if the device was exposed to high humidity. Also if the device is still
running, the device must be checked by a specialist if the liquid has reduced any insulation. Reduced
insulation can cause mortal electrical shock.
There must never be any objects entering into the device. This is especially valid for metal parts. If any metal
parts like staples or coarse metal chips enter into the device, the device must be taken out of operation and
disconnected immediately. Malfunction or short-circuits caused by metal parts may cause mortal injuries.
During the initial start-up some smoke or smell may arise. This is a normal process and does not necessarily
mean that the device is defective.
Danger of burning! Never install the device on a highly flammable surfaces (e.g. fair carpet)!
Caution: During the operation, the housing becomes very hot.
Do not switch the device on and off in short intervals as this would reduce the lamp’s life.

51838155_V_1_1.DOC
32/104
HEALTH HAZARD!
Never look directly into the light source, as sensitive persons may suffer an
epileptic shock (especially meant for epileptics)!
Keep away children and amateurs!
Never leave this device running unattended.
OPERATING DETERMINATIONS
This device is a moving-head spot for creating decorative effects. This product is only allowed to be operated
with an alternating current of 220-250 V, 50 Hz and was designed for indoor use only.
This device is designed for professional use, e.g. on stages, in discotheques, theatres etc.
Lighting effects are not designed for permanent operation. Consistent operation breaks will ensure that the
device will serve you for a long time without defects.
Do not shake the device. Avoid brute force when installing or operating the device.
Never lift the fixture by holding it at the projector-head, as the mechanics may be damaged. Always hold the
fixture at the transport handles.
When choosing the installation-spot, please make sure that the device is not exposed to extreme heat,
moisture or dust. There should not be any cables lying around. Please make sure that the unit cannot be
touched or bumped. You endanger your own and the safety of others!
This device must never be operated or stockpiled in sourroundings where splash water, rain, moisture or fog
may harm the device. Moisture or very high humidity can reduce the insulation and lead to mortal electrical
shocks. When using smoke machines, make sure that the device is never exposed to the direct smoke jet
and is installed in a distance of 0.5 meters between smoke machine and device. The room must only be
saturated with an amount of smoke that the visibility will always be more than 10 meters.
The ambient temperature must always be between -5° C and +45° C. Keep away from direct insulation
(particularly in cars) and heaters.
The relative humidity must not exceed 50 % with an ambient temperature of 45° C.
This device must only be operated in an altitude between -20 and 2000 m over NN.
Never use the device during thunderstorms. Over voltage could destroy the device. Always disconnect the
device during thunderstorms.
The symbol
---m
determines the minimum distance from lighted objects. The minimum distance
between light-output and the illuminated surface must be more than this value.
The device must only be installed on a non-flammable surface. In order to safeguard sufficient ventilation,
leave 50 cm of free space around the device. Please note that heat-sensitive objects may be deformed or
damaged by the emitted heat.
Make sure that the area below the installation place is blocked when rigging, derigging or servicing the
fixture.
For overhead use (mounting height >100 cm), always fix the fixture with an appropriate safety-rope. Fix the
safety-rope at the correct fixation points only. The safety-rope must never be fixed at the transport handles!
Only operate the fixture after having checked that the housing is firmly closed and all screws are tightly
fastened.

51838155_V_1_1.DOC
33/104
The lamp must never be ignited if the objective-lens or any housing-cover is open, as discharge lamps may
explose and emit a high ultraviolet radiation, which may cause burns.
The maximum ambient temperature ta= 45° C must never be exceeded.
Operate the device only after having familiarized with its functions. Do not permit operation by persons not
qualified for operating the device. Most damages are the result of unprofessional operation!
Please use the original packaging if the device is to be transported.
Please consider that unauthorized modifications on the device are forbidden due to safety reasons!
Never remove the serial barcode from the device as this would make the guarantee void.
If this device will be operated in any way different to the one described in this manual, the product may suffer
damages and the guarantee becomes void. Furthermore, any other operation may lead to dangers like short-
circuit, burns, electric shock, lamp explosion, crash etc.
DESCRIPTION OF THE DEVICE
Features
Medium-Moving-Head
DMX-controlled operation or stand alone operation with Master/Slave-function • 48 preprogrammed scenes
in Program Run for stand alone operation • Number of scenes in Program Run can be changed individually •
The scenes in Program Run can be modified via the Control Board or via an external controller and loaded
into the memory • 8 built-in programs can be called up via DMX-controller • Sound-controlled via built-in
microphone • 8 brilliant, dichroic colours plus white • Switchable colour change (mode 1: only full colours,
mode 2: colour-change at every position) • Rainbow-effect with adjustable speed in both directions • Gobo-
wheel with 6 rotating gobos plus open • All gobos can be interchanged • With gobo-shake function • Exact
positioning via 16 bit Pan/Tilt movement resolution • Manual focus • Strobe-effect with 1-10 flashes per
second • Mechanic dimmer • Positioning within 540° Pan and 265° Tilt • 10 DMX-channels • Control-Board
with 4-digit display and foil-keyboard for adjusting the DMX-starting address, Pan/Tilt-Reverse, Program,
Reset, lamp on/off • For bright 150 W discharge lamp • DMX-control via every standard DMX-controller •
Suitable FUTURELIGHT controllers: CP-528 controller, CP-256/32 Controller

51838155_V_1_1.DOC
34/104
Overview
(1) Projector head
(2) Objective-lens
(3) Yoke
(4) Base
(5) Control Board
(6) Ventilation fan
(7) Housing screws
(8) Mode/Enter-button
(9) Down-button
(10) Up-button
(11) Display

51838155_V_1_1.DOC
35/104
(12) DMX-Out socket
(13) DMX-In socket
(14) Carrying handle
(15) Fuseholder
(16) Power supply
(17) Lamp system

51838155_V_1_1.DOC
36/104
(18) Feet
(19) Fixation holes adapter plate
(20) Safety-rope holes

51838155_V_1_1.DOC
37/104
INSTALLATION
Installing/Replacing the lamp
DANGER TO LIFE!
Only install the lamp with the device switched off!
Unplug from mains before!
For the installation, you need one CDM 150 lamp.
The lamp must only be changed when wearing appropriate protective clothing (protection glasses, protection
gloves, helmet with sight, leather apron).
The lamp has to be replaced when it is damaged
or deformed due to the heat!
CAUTION!
The lamp life given by the manufacturer must never be exceeded. This is why you need to take notes on the
operational time of the lamp and replace the lamp in time.
Keep exchanged lamp in a protective container and remove accordingly.
During the operation, the lamp reaches temperatures of up to 600° C.
Before replacing the lamp, unplug mains lead and let the lamp cool down (approx. 10 minutes).
During the installation do not touch the glass-bulbs bare-handed! Please follow the lamp manufacturer's
notes!
Do not install lamps with a higher wattage! Lamps with a higher wattage generate temperatures the device
was not designed for. Damages caused by non-observance are not subject to warranty.
Procedure:
Step 1: Unscrew the fixation screws A and B of the lamp system and carefully remove it from the
housing.
Step 2: If replacing the lamp, remove the old lamp from the lamp holder.
Step 3: Insert the lamp into the lamp holder.
Step 4: Replace the lamp system in the housing and tighten the fixation screws.
Step 5: Adjust the lamp as described under lamp adjustment.
Do not operate this device with opened cover!

51838155_V_1_1.DOC
38/104
Lamp adjustment
The lampholder is aligned at the factory. Due to
differences between lamps, fine adjustment may
improve light performance.
Strike the lamp, open the shutter, set the dimmer
intensity onto 100 % and direct the light towards a flat
surface (wall). Center the hot-spot (the brightest part
of the beam) using the 3 adjustment screws "1, 2, 3”.
Turn one screw at a time to drag the hot-spot
diagonally across the projected image. If you cannot
detect a hot-spot, adjust the lamp until the light is
even.
To reduce a hot-spot, pull the lamp in by turning all
three screws "1, 2, 3” clockwise ¼-turn at a time until
the light is evenly distributed.
If the light is brighter around the edge than it is in the
center, or if light output is low, the lamp is too far back
in the reflector. "Push” the lamp out by turning the
screws "1, 2, 3” counterclockwise ¼-turn at a time the
light is bright and evenly distributed.
Inserting/Exchanging gobos
DANGER!
Install the gobos with the device switched off only.
Unplug from mains before!
If you wish to use other forms and patterns as the standard-gobos, or if gobos are to be exchanged, please
follow the instructions below:
CAUTION!
Never unscrew the screws of the rotating gobo
as the ball bearing will otherwise be opened!
Remove the fixation-ring with an appropriate tool. Remove the gobo and insert the new gobo. Press the
fixation-ring together and insert it in front of the gobo.
When installing metal gobos, please make sure that the mirror-inverted side points away from the lamp.
When installing glass-gobos, please make sure that the coated side points to the lamp.

51838155_V_1_1.DOC
39/104
Rigging
DANGER TO LIFE!
Please consider the EN 60598-2-17 and the respective national norms during the
installation! The installation must only be carried out by an authorized dealer!
The installation of the projector has to be built and constructed in a way that it can hold 10 times the weight
for 1 hour without any harming deformation.
The installation must always be secured with a secondary safety attachment, e.g. an appropriate catch net.
This secondary safety attachment must be constructed in a way that no part of the installation can fall down
if the main attachment fails.
When rigging, derigging or servicing the fixture staying in the area below the installation place, on bridges,
under high working places and other endangered areas is forbidden.
The operator has to make sure that safety-relating and machine-technical installations are approved by an
expert before taking into operation for the first time and after changes before taking into operation another
time.
The operator has to make sure that safety-relating and machine-technical installations are approved by an
expert after every four year in the course of an acceptance test.
The operator has to make sure that safety-relating and machine-technical installations are approved by a
skilled person once a year.
Procedure:
The projector should be installed outside areas where persons may walk by or be seated.
IMPORTANT! OVERHEAD RIGGING REQUIRES EXTENSIVE EXPERIENCE, including (but not limited to)
calculating working load limits, installation material being used, and periodic safety inspection of all
installation material and the projector. If you lack these qualifications, do not attempt the installation yourself,
but instead use a professional structural rigger. Improper installation can result in bodily injury and.or
damage to property.
The projector has to be installed out of the reach of people.
If the projector shall be lowered from the ceiling or high joists, professional trussing systems have to be
used. The projector must never be fixed swinging freely in the room.
Caution: Projectors may cause severe injuries when crashing down! If you have doubts concerning the
safety of a possible installation, do NOT install the projector!
Before rigging make sure that the installation area can hold a minimum point load of 10 times the projector's
weight.
DANGER OF FIRE!
When installing the device, make sure there is no highly-inflammable
material (decoration articles, etc.) within a distance of min. 0.5 m.
CAUTION!
Use 2 appropriate clamps to rig the fixture on the truss.
Follow the instructions mentioned at the bottom of the base.
Make sure that the device is fixed properly! Ensure that
the structure (truss) to which you are attaching the fixtures is secure.

51838155_V_1_1.DOC
40/104
The Moving-Head can be placed directly on
the stage floor or rigged in any orientation on
a truss without altering its operation characte-
ristics (see the drawing).
The fixture’s base enables to be mounted in
two ways.
For overhead use (mounting height >100 cm),
always install a safety-rope that can hold at
least 12 times the weight of the fixture. You
must only use safety-ropes with quick links
with screw cap. Pull the safety-rope through
the hole on the bottom of the base and over
the trussing system etc. Insert the end in the
quick link and tighten the fixation screw.
The maximum drop distance must never
exceed 20 cm.
A safety rope which already hold the strain of
a crash or which is defective must not be used
again.
DANGER TO LIFE!
Before taking into operation for the first time, the installation has to be approved by an expert!
Installation via the adapter plate
Screw both clamps via a M12 screw and nut onto the respective holes in the adapter plate.
The clamps may either be installed horizontally or vertically.
Insert the four quick-lock fasteners of the adapter plate into the respective holes on the bottom of the device.
Tighten the quick-lock fasteners fully clockwise.

51838155_V_1_1.DOC
41/104
DMX-512 connection / connection between fixtures
Projector 1
Starting address 1
Projector 2
Starting address 11
Projector 3
Starting address 21
DMX-512 Controller
120 Ohms
The wires must not come into contact with each other, otherwise
the fixtures will not work at all, or will not work properly.
Only use a stereo shielded cable and 3-pin XLR-plugs and connectors in order to connect the controller with
the fixture or one fixture with another.
Occupation of the XLR-connection:
If you are using controllers with this occupation, you can connect the DMX-output of the controller directly
with the DMX-input of the first fixture in the DMX-chain. If you wish to connect DMX-controllers with other
XLR-outputs, you need to use adapter-cables.
Building a serial DMX-chain:
Connect the DMX-output of the first fixture in the DMX-chain with the DMX-input of the next fixture. Always
connect one output with the input of the next fixture until all fixtures are connected.
Caution: At the last fixture, the DMX-cable has to be terminated with a terminator. Solder a 120 Ωresistor
between Signal (–) and Signal (+) into a 3-pin XLR-plug and plug it in the DMX-output of the last fixture.
Connection with the mains
Connect the device to the mains with the enclosed power supply cable.

51838155_V_1_1.DOC
42/104
The occupation of the connection-cables is as follows:
Cable Pin International
Brown Live L
Blue Neutral N
Yellow/Green Earth
The earth has to be connected!
If the device will be directly connected with the local power supply network, a disconnection switch with a
minimum opening of 3 mm at every pole has to be included in the permanent electrical installation.
Lighting effects must not be connected to dimming-packs.
OPERATION
After you connected the effect to the mains, the PHS-150 starts running. During the Reset, the motors are
trimmed and the device is ready for use afterwards.
Stand Alone operation
In the Stand Alone mode, the PHS-150 can be used without controller.
Disconnect the PHS-150 from the controller and call the internal program.
1.Press [ENTER] for 3 seconds to enter the main menu "MODE" (display flashing)
2.Press [ENTER] and select “RUN” by pressing [UP] button.
3.Press [ENTER] and select “AUTO” by pressing [UP] button.
4.Press [ENTER] and select “ALONE” by pressing [UP] button.
5.Press [ENTER] for confirmation.
6.Press [EXIT/DN] until the display shows “AU-A”.
Please refer to the instructions under Control Board, Main functions, menus Run and Edit.
DMX-controlled operation
You can control the projectors individually via your DMX-controller. Every DMX-channel has a different
occupation with different features. The individual channels and their features are listed under DMX-protocol.
Addressing
The Control Board allows you to assign the DMX starting address, which is defined as the first channel from
which the PHS-150 will respond to the controller.
If you set, for example, the address to channel 11, the PHS-150 will use the channel 11 to 20 for control.
Please, be sure that you don’t have any overlapping channels in order to control each PHS-150 correctly and
independently from any other fixture on the DMX-chain.
If several PHS-150 are addressed similarly, they will work synchronically.
Press the Up/Down-buttons for setting the desired starting address. Now you can start operating the PHS-
150 via your lighting controller.
Note:
The modes of DMX 512 data and lamp are shown via the display:
1. After switching on, the device will automatically detect whether DMX 512 data is received or not. If the
data is received, the the display will show "A.001" with the actually set address. If there is no data received
at the DMX-input, the display will flash "A001" with the actually set address.
This situation can occur if:

51838155_V_1_1.DOC
43/104
- the 3 PIN XLR plug (cable with DMX signal from controller) is not connected with the input of the device.
- the controller is switched off or defective, if the cable or connector is defective or the signal wires are swap
in the input connector.
Note:
It’s necessary to insert the XLR termination plug (with 120 Ohm) in the last lighting in the link in order to
ensure proper transmission on the DMX data link.
2. If the lamp is on, the the display will show "A00.1" with the actually set address. If the lamp is off, the the
display will show "A001" with the actually set address.
DMX-protocol
Control channel 1 - Horizontal movement (Pan)
Push slider up in order to move the head horizontally (PAN).
Gradual head adjustment from one end of the slider to the other (0-255, 128-center). The head can be
stopped at any position you wish.
Control channel 2 - Vertical movement (Tilt)
Push slider up in order to move the head vertically (TILT).
Gradual head adjustment from one end of the slider to the other (0-255, 128-center). The head can be
stopped at any position you wish.
Control channel 3 - Pan/Tilt-speed
DMX-value Feature
0-4 Maximum speed
5-225 Decreasing speed
226-235 Blackout with Pan/Tilt-movement
236-245 Blackout with colour/gobo-change
246-255 No function
Control channel 4 - Colour-wheel
Linear colour change following the movement of the slider. In this way you can stop the colour-wheel in any
position.
DMX-value Feature
0-13 Open / white
14-27 Orange
28-41 Blue
42-55 Green
56-69 Yellow
70-83 Red
84-97 Pink
98-111 Cyan
112-127 Magenta
128-187 Forwards rainbow effect with decreasing speed
188-193 No rotation
194-255 Backwards rainbow effect with increasing speed

51838155_V_1_1.DOC
44/104
Control channel 5 - Rotating gobo-wheel, gobo shake
DMX-value Feature
0-9 Open
10-19 Gobo 1
20-29 Gobo 2
30-39 Gobo 3
40-49 Gobo 4
50-59 Gobo 5
60-69 Gobo 6
70-89 Gobo 1 shake with increasing speed
90-109 Gobo 2 shake with increasing speed
110-129 Gobo 3 shake with increasing speed
130-149 Gobo 4 shake with increasing speed
150-169 Gobo 5 shake with increasing speed
170-189 Gobo 6 shake with increasing speed
190-255 Cont. gobo-wheel rotation with increasing speed
Control channel 6 - Rotating gobo index, gobo rotation
DMX-value Feature
0-127 Gobo indexing
128-187 Forwards gobo rotation with decreasing speed
188-193 No rotation
194-255 Backwards gobo rotation with increasing speed
Control channel 7 - Shutter, strobe
DMX-value Feature
0-31 Shutter closed
32-63 Dimmer control 0-100 %
64-95 Strobe-effect with increasing speed (max. 10 flashes/sec.)
96-127 No function (shutter open)
128-159 Pulse-effect in sequences
160-191 No function (shutter open)
192-223 Random strobe-effect with increasing speed
224-255 No function (shutter open)
Control channel 8 - Switching the lamp, Reset, internal programs
DMX-value Feature
0-15 Normal colour-change, search position via shortest distance
16-31 Normal colour-change, search position clockwise
32-47 Colour-change at every position, search position via shortest distance
48-63 Colour-change at every position, search position clockwise
64-79 Lamp on
80-95 Reset
96-111 Internal program 1
112-127 Internal program 2
128-143 Internal program 3
144-159 Internal program 4
160-175 Internal program 5
176-191 Internal program 6
192-207 Internal program 7
208-223 Internal program 8
224-239 Lamp off
240-255 No function
Control channel 9 - Pan-movement with 16 Bit-resolution
Control channel 10 - Tilt-movement with 16 Bit-resolution

51838155_V_1_1.DOC
45/104
Control Board
The Control Board offers several features: you can simply set the starting address, switch on and off the
lamp, run the pre-programmed program or make a reset.
The main menu is accessed by pressing the Enter-button for 3 seconds until the display starts flashing.
Browse through the menu by pressing the Up-button. Press the Enter-button in order to select the desired
menu. You can change the selection by pressing the Up-button. Confirm every selection by pressing the
Enter-button. You can leave every mode by pressing the Exit-button. The functions provided are described in
the following sections.
Default settings shaded.
Main
menu Sub menu Extension Display Function
VALU A001~A511 (AXX) DMX address setting
SLAV ON/OFF (SLAV) Slave setting
ADDR EBOC ON/OFF Change DMX address via
external controller
AUTO ALON (AU-A) Automatic Program Run
in Stand Alone
MAST (AU-M) Automatic Program Run
as Master
SOUN ALON (SO-A) Sound-controlled Program Run
in Stand Alone
RUN
MAST (SO-M) Sound-controlled Program Run
as Master
VALU D-00 ~ D-30 (DXX)
D-00
Display the DMX 512 value of
each channel
RDIS ON/OFF Reverse display
0MODE
DISP
CLDI ON/OFF Shut off LED display
OPEN ON/OFF Lamp on/off
ONLI ON/OFF Lamp on/off via controller
1LAMP
DELA D–00 ~ D-59, D-15 Delay lamp on
RPAN ON/OFF Pan Reverse
RTIL ON/OFF Tilt Reverse
16BI ON/OFF Switch 16 bit/8 bit
REST ON/OFF Reset
LODA ON/OFF Restore factory settings
2 SET
VER V-1.0~V-9.9 Software version
LADJ ON/OFF Lamp adjustment
3ADJU TEST T–01 ~ T–30 Test function of each channel
MATI 0000~9999 (hours) Fixture running time
LATI 0000~9999 (hours) Lamp running time
CLMT ON/OFF Service-function
4TIME
CLLT ON/OFF Clear lamp time
STEP S–01 ~ S–48 Steps of Program Run
C01 ~ C30 01XX (00~FF)
30XX (00~FF)
Edit the channels of each scene
TIME (sec.) T – – X (1~9) Time for each scene
5EDIT SC01
~
SC48 CNIN ON/OFF Edit program via controller

51838155_V_1_1.DOC
46/104
Main functions
- Main menu 0
♦Press [ENTER] for 3 seconds to enter the main menu "MODE" (display
flashing)
♦Press [ENTER] and select "ADDR", “RUN” or "DISP" by pressing [UP]
button.
♦Press [ENTER] for selecting the desired sub menu.
- DMX address setting, Slave setting
- DMX address setting
With this function, you can adjust the desired DMX-address via the Control Board.
♦Select “VALU“ by pressing [UP] button.
♦Press [ENTER], adjust the DMX address by pressing [UP] or [DN].
♦Press [ENTER] to confirm.
♦Press [EXIT/DN] in order return to main menu.
- Slave setting
With this function, you can define the device as slave.
♦Select “SLAV” by pressing [UP] button.
♦Press [ENTER], the display shows “ON” or “OFF”.
♦Press [UP] to select “ON” if you wish to enable this function or “OFF” if you don’t.
♦Press [ENTER] to confirm.
♦Press [EXIT/DN] in order to return to the main menu.
- DMX address setting via controller
With this function, you can adjust the desired DMX-address via an external controller.
♦Select “EBOC“ by pressing [UP] button.
♦Press [ENTER], the display shows “ON” or “OFF”.
♦Press [UP] to select “ON” if you wish to enable this function or “OFF” if you don’t.
♦Press [ENTER] to confirm.
♦Press [EXIT/DN] in order to return to the main menu.
♦On the controller, set the DMX-value of channel 1 to "7".
♦Set the DMX-value of channel 2 to "7"or "8". When set to "7" you can adjust the starting address
between 1 and 255. When set to "8" you can adjust the starting address between 256 and 511.
♦Set the DMX-value of channel 3 to the desired starting address. If you want to set the starting
address to 57, set channel 1 to "7", channel 2 to "7" and channel 3 to "57". If you want to set the
starting address to 420, set channel 1 to "7", channel 2 to "8" and channel 3 to "164" (256+164=420).
♦Wait for approx. 20 seconds and the unit will carry out a reset. After that, the new starting address is
set.
Run
- Program Run, Master setting
With the function "RUN", you can run the internal program. You can set the number of steps under Step.
You can edit the individual scenes under Edit. You can run the individual scenes either automatically
(AUTO), i.e. with the adjusted Step-Time or sound-controlled (SOUN). The selection "ALON" means
Stand Alone-mode and "MAST" that the device is defined as master.