FUVISION S30 User manual

OUTDOOR WIRELESS SOLAR CAMERA
USER MANUAL
MODEL：S30

QUICK GUIDE
FOR S30
STEP1.
When you first get the camera, please charge the camera for 10 hours by
2A/5V or 12 hours by 1A/5V adaptor, there is no charge status LED showing
on the camera. You can only check the battery status from the UBOX APP
after you finish the subsequent set up process.
STEP2.
Download UBOX APP from APP store or Google play.
STEP3.
Register an account in UBOX app.
a.Open the app and register your account with your Email address and it
is recommended to verify your account from email so that you can retrieve
password of your UBOX account in case.
b.Set a password for your account and make note to remember it
c.Click Allow or Agree on all access when you set up your account and
camera.
d.Finish the register process according to the voice prompt or User manual
booklet.
NOTE:
The required fields are country and state on Add address page which locate
your correct region server for a proper notifications and full functions of your
camera.

STEP4.
Please check and make sure your phone connected well your router 2.4G
Wi-Fi firstly.
Note:
a.Please let your phone to forget your 5G Wi-Fi password to avoid phone
pick up your 5g Wi-Fi as priority automatically.
b.Please make sure your router Wi-Fi password correct and camera, phone,
router are in the same Wi-Fi connection.
STEP5.
Please turn on your camera and you will hear the voice prompt “The camera
is now ready to begin pairing” and Camera Blue LED blinks the same time,
which means the camera is ready and waiting for pair up.
STEP6.
Pair up your camera according to the user manual. Use camera to scan the
QR code which generated by the app on your phone.

STEP7.
When you get into the Connect to Wi-Fi page, if your phone connected well
with your router 2.4g Wi-Fi as Step 4 stated, your Wi-Fi name should pop-up
automatically here.
Otherwise, you'll need to recheck your router Wi-Fi connection again.
If you Wi-Fi name didn't pop-up automatically, please check below and tick
the location permission from your phone setting for UBOX APP.
TROUBLE SHOOTING FOR PAIR UP:
1. lf the camera LED doesn't blink blue,which means the camera is not in
ready to pair condition.
1.1 Please power on the camera and hold on the reset button for 4-5 seconds
and release it when you hear "system reset" to reset your camera to default.
2. When your camera always blinks and won't go into next step，which means
your camera didn't pick up your QR code information or didn't pick up your
Wi-Fi correctly
2.1 Please make sure your phone is connected with your 2.4G Wi-Fi.
2.2 Please let your phone to forget your 5G Wi-Fi connection from your Phone
Wi-Fi list.
2.3 Please try to avoid your phone screen too light or too dark so that camera
can read the QR code clearly without reflecting light.
2.4 Put your phone, camera and router within 1.5ft to get a strong Wi-Fi signal
strength.
2.5 lf you use sound wave pair up,please make sure your phone volume is
turned up and your router lD + password no more than 32 digits.
3. Pair up failed after you got 100% process finished or Camera LED stays
blue or red,which means your camera can not recognize or timeout to obtain
your router lP.

MORE TIPS FOR YOUR REFERENCE:
1. Micro sd card is an option to store more videos but not a must if you plan
to use UBOX cloud service. Install micro sd card only when you power off
the camera.Camera doesn't support plug&play.
2. The camera is defaulted as SD(720P) for a smooth transmission,you can
click it to change to HD (1080P) for high resolution.Or set HD(1080p) as
default from common settings.
3.1 Put your phone, camera and router within 1.5ft to get a strong Wi-Fi signal
strength.
3.2 Please enable your router SSID and DHCP function so that your router can
send out Wi-Fi signal and allocate dynamic lP address to avoid conflict
with your other wireless devices for one static IP address.
3.3 Reboot your router to reallocate your lP address and refresh your
network.4) Reset the camera and change to sound wave pair up method
for a try.
4. Camera always prompt up with" incorrect password"
4.1 You may switch upper case to input your special character wrongly.
4.2 Recommend you to change a Wi-Fi password for your router with 8-12
digits(numbers+letters)without special character to avoid input errors.
LED indicators trouble shooting:
Camera LED blinks blue: Camera is ready for pairing Camera LED stays
blue: Camera paired successfully
Camera LED Blinks red once and stay solid blue: Camera detected motion
Camera NO LED after pairing successfully: Camera is in standby mode
Camera LED stays red: Camera didn't pick up Wi-Fi correctly
Camera LED always blinks red: Camera hardware defective
Click here to chose the resolution
to HD(1080P) OR SD(720P)

DETAILED APP INSTRUCTIONS
Enter to select your family or smart device location
Turn on/off the push notification.
Settings: Sharing, Cloud storage,Delete the device..
Press to enter the preview section.
Press to add a smart device
Smart device basic settings
Could set "Storage management, Flip screen,
Environmental model,PIR detection, Sleep time,
Power frequency, LED indicator，Device name"
Could check the information of "Device name,
Device ID,Model,FW version,Manufacturer,
Check for the FW updates.."
Start Cloud service Pan tilt control

SPECIAL NOTES!
1. The device is equipped with a rechargeable lithium battery. The battery life will be affected by
the device wake-up time and the number of wake-ups. Therefore, the PIR sensor alarm
detection function is used in an environment with a Iot of people. It is recommended to tum off
or set the device to low sensitivity to reduce device wake-up and call times extend battery life.
When the battery is low, please charge the battery immediately.
2. Keep the device in range of your router.Make sure the device is placed close to the Wi-Fi router.
If there has to be thick or insulated objects between the device and the Wi-Fi router, which may
lead to weak Wi-Fi signal, please make sure the Wi-Fi signal is in good level before you start
using the device.
3. It is a delicate device with low power consumption design. Every time the device is awakened
and will work for few seconds After that, the device will enter standby mode to save power. You
can set the work time in the app settings.
4. Because the mainland China does not receive Google's system push messages, you need to
open the app's self-starting function in your phone to receive push messages.
5. This device provides one month of free cloud storage services. If you need to continue using
value-added services after the trial period expires, you need to purchase them in the app.
Check "my account"name and change password;
Check and purchase the Cloud storage;
Check and add my friends list and permission;
Set the default voice and resolution for the
devices;
Press to add a smart device
Choose the desired date to check all videos
from the cloud.
Click the "Calendar"icon on the right top corner,
then choose the date to playback
the voices from cloud storage.
Check and purchase the Al Cloud Facial
Recognition;

CUSTOMER CARE EMAIL:[email protected]