INSTALLATION GUIDE: WIRELESS LUXOR LINKING
Learn more about FX Luminaire products. Visit fxl.com or call Technical Service at 1-760-591-7383. FX-331 12/21
https://fxl.help/luxor
PRIMARY LUXOR CONTROLLER
1. Using the Wireless Linking Module assigned to Chassis Number 0 (Primary), insert the wireless linking
cable through the ⁄" (22 mm) hole on bottom of the Luxor Controller enclosure.
2. Slide the supplied nut over the wire to secure the Wireless Linking Module in place.
3. Plug the Wireless Linking Module into one of the linking ports.
4. For remote mount installations, thread the Wireless Linking Module into the supplied mount. Secure
with screws.
SATELITTE LUXOR CONTROLLERS
1. Using the Wireless Linking Module assigned to the desired Chassis Number 1–10 (for the Luxor Satellite
Controllers), insert the wireless linking cable through the ⁄" (22 mm) hole on the bottom of the Luxor
Controller enclosure.
2. Slide the supplied nut over the wire to secure the Wireless Linking Module in place.
3. Plug the Wireless Linking Module into one of the linking ports.
4. For remote mount installations, thread the Wireless Linking Module into the supplied mount. Secure
with screws.
Note: The maximum cable distance between the primary Luxor Controller and the farthest satellite
controller is 3,000' (914 m) line of sight.
AB
DETAIL
A
SCALE 1 : 2
DETAIL
B
SCALE 1 : 2
E0000
AAA
7/22/2012
REV
ECO REVISION DESCRIPTION
DRFT
DATE
N/A
MATERIAL:
PRODUCT:
DRAWN
BY:
11/10/2021
SIZE:
B
THIRD ANGLE PROJ.
.XX = ±.01
.XXX = ±.005
.XXXX = ±.0005
SHEET 1 OF 1
Hunter Industries
Engineering
1940 Diamond St.
San Marcos, CA 92078
±1°
ANGLES:
N/A
wireless linking
module
LINKMOD
1:8
DO NOT SCALE DRAWING
ALL DIMENSIONS ARE IN INCHES
SURFACE FINISH:
UNLESS OTHERWISE SPECIFIED:
PRINT
DATE:
REV.
DRAWING NO.
SCALE:
Material
Spec:
Color:
TITLE:REL.
DATE:
DIMENSIONAL
TOLERANCES:
CONFIDENTIAL AND PROPRIETARY
THIS DRAWING/DOCUMENT CONTAINS TRADE SECRET INFORMATION OF HUNTER INDUSTRIES, INC. USE, PUBLICATION, AND/OR
DISCLOSURE OF THIS INFORMATION TO THIRD PARTIES ARE ALL PROHIBITED EXCEPT AS EXPRESSLY AUTHORIZED IN ADVANCE BY HUNTER.
NO PATENT LICENSE IS GRANTED TO ANY INVENTIONS DESCRIBED AND/OR ILLUSTRATED HEREIN. ©COPYRIGHT HUNTER INDUSTRIES, INC.
B1 FORMAT REVISION 1 / 11 / 2018
DENOTES CRITICAL INSPECTION POINTS
DENOTES FUNCTIONALLY CRITICAL POINTS
Controller Mount
Remote Mount
E0000
AAA
7/22/2012
REV
ECO REVISION DESCRIPTION
DRFT
DATE
APVD
N/A
MATERIAL:
PRODUCT:
DRAWN
BY:
11/10/2021
SIZE:
A
THIRD ANGLE PROJ.
.XX = ±.01
.XXX = ±.005
.XXXX = ±.0005
SHEET 1 OF 1
Hunter Industries
Engineering
1940 Diamond St.
San Marcos, CA 92078
±1°
ANGLES:
N/A
wireless linking
module
LINKMOD
1:2
DO NOT SCALE DRAWING
ALL DIMENSIONS ARE IN INCHES
SURFACE FINISH:
UNLESS OTHERWISE SPECIFIED:
PRINT
DATE:
REV.
DRAWING NO.
SCALE:
DESIGNER:
CHECKED
BY:
TITLE:REL.
DATE:
DIMENSIONAL
TOLERANCES:
THIS DRAWING/DOCUMENT CONTAINS TRADE SECRET INFORMATION OF HUNTER INDUSTRIES, INC. USE, PUBLICATION, AND/OR
DISCLOSURE OF THIS INFORMATION TO THIRD PARTIES ARE ALL PROHIBITED EXCEPT AS EXPRESSLY AUTHORIZED IN ADVANCE BY HUNTER.
NO PATENT LICENSE IS GRANTED TO ANY INVENTIONS DESCRIBED AND/OR ILLUSTRATED HEREIN. ©COPYRIGHT HUNTER INDUSTRIES, INC.
CONFIDENTIAL AND PROPRIETARY
B1FORMAT REVISION 08/27/12
DENOTESFUNCTIONALLY CRITICAL POINTS
DENOTESCRITICAL INSPECTION POINTS
Regulatory and Legal Information
This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses
and can radiate radio frequency energy, and if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will
not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the
followingmeasures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that
to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
The user is cautioned that changes/modifications not approved by the
responsible party could void the user’s authority to operate the equipment.
To satisfy FCC RF Exposure requirements for mobile and base station
transmission devices, a separation distance of 20 cm or more should
be maintained between the antenna of this device and persons during
operation. To ensure compliance, operation at a closer distance is not
recommended. The antenna(s) used for this transmitter must not
be co-located or operating in conjunction with any other antenna or
transmitter. Under Industry Canada regulations, this radio transmitter
may only operate using an antenna of a type and maximum (or lesser)
gain approved for the transmitter by Industry Canada. To reduce potential
radio interference to other users, the antenna type and its gain should be
chosen so that the equivalent isotropically radiated power (e.i.r.p.) is not
more than that necessary for successful communication.
Wi-Fi Legal Information
Conformément à la réglementation d’Industrie Canada, le présent émetteur
radio peut fonctionner avec une antenne d’un type et d’un gain maximal
(ou inférieur) approuvé pour l’émetteur par Industrie Canada. Dans le but de
réduire les risques de brouillage radioélectrique à l’intention des autres
utilisateurs, il faut choisir le type d’antenne et son gain de sorte que la
puissance isotrope rayonnée équivalente (p.i.r.e.) ne dépasse pas l’intensité
nécessaire à l’établissement d’une communication satisfaisante.
This device contains license-exempt transmitter(s)/receiver(s) that comply
with Innovation, Science and Economic Development Canada’s license-
exempt RSS(s). Operation is subject to the following two conditions:
1. This device may not cause interference.
2. This device must accept any interference, includinginterference that may
cause undesired operation of the device.
L’émetteur/récepteur exempt de licence contenu dans le présent
appareil est conforme aux CNR d’Innovation, Sciences et Développement
économique Canada applicables aux appareils radio exempts de licence.
L’exploitation est autorisée aux deux conditions suivantes :
1. L’appareil ne doit pas produire de brouillage;
2. L’appareil doit accepter tout brouillage radioélectrique subi, même si le
brouillage est susceptible d’en compromettre le fonctionnement.
To ensure compliance with FCC and ISED RF exposure requirements this
device must be installed to provide a minimum of 20 cm betweenthe device
and people.
Pour garantir la conformité aux exigences d'exposition RF de la FCC et
d'ISED Canada, cet appareil doit être installé de manière à laisser un
minimum de 20 cm entre l'appareil et les personnes.
INSTALLING WIRELESS LINKING MODULES
