FXLuminaire A-NK6 Instruction sheet

INSTALL NOTE: A-NK6
LANDSCAPE & ARCHITECTURAL LIGHTING | Learn more. Visit fxl.com
1. Caution and Safety Instructions
• Qualied personnel must install product in a
manner consistent with its intended use and in
compliance with the National Electrical Code,
Canadian Electrical Code, and/or all Local and
Provincial Codes.
• Follow all product label information and
installation instructions.
• Qualied personnel must perform all servicing of
this product.
• Turn o power at the fuse or circuit breaker before
installation or servicing.
• The use of damaged components may cause an
unsafe condition and void the product warranty.
• Do not block light emanating from the product in
whole or part.
• Never operate the xture with a missing or
damaged lens. The lens must be cleaned on a
regular basis.
• The entire xture may become extremely hot.
Do not touch the hot lens or xture body. Do not
touch the light source at any time.
• Keep all gaskets and sealing surfaces clean during
installation and servicing; failure to do so may lead
to premature failure of the product.
67
IP
2. Product Information
• Suitable for mounting within 4' (1.2 m) of the ground
• Vapor barrier must be suitable for 194°F (90°C)
• For use in non-re-rated installations only
• Not for use in environmental air-handling spaces
3YJ8

INSTALL NOTE: A-NK6
LANDSCAPE & ARCHITECTURAL LIGHTING | Learn more. Visit fxl.com
2. Product Information (cont.)
10" (254 mm)
9.4" (239 mm)
9.3" (235 mm)
6.3" (160 mm)
3.8" (96 mm)
⁄"-14 NPT knockout (x3)
5.3" (135 mm)
Tools Needed:
• ⁄" Allen key (installation)
• #3 Phillips screwdriver (installation)
• #1 & #2 Phillips screwdriver (servicing)
Standard Voltage (SV) Universal Voltage (UV) High Voltage (HV)
Input Power 120V 110V to 277V 220V to 240V
Dimming Phase 0-10V N/A
Number of Wires 3 5 3
Black, White, Green Black, White, Green,
Purple, Gray Brown, Blue, Green/Yellow
Power Requirements

INSTALL NOTE: A-NK6
LANDSCAPE & ARCHITECTURAL LIGHTING | Learn more. Visit fxl.com
3. Product Installation
1. Install construction sleeve (“sleeve”) inside
the wall using provided L-brackets, mounting
to structural supports (e.g., 2"x4" (50 mm x
100 mm) framing studs). For lighting in the
downward direction, ensure the arrow in the
sleeve is pointing upward.
Wiring Chart (North America)
Wiring Chart (International)
BlackLine/Hot/Switching
WhiteCommon
Green (via stud or
green lead)
Ground
Gray*0-10V (-)
Purple*0-10V (+)
FIXTUREFIXTURE
BUILDINGBUILDING
*For use with 0-10V driver only
*For use with 0-10V driver only
Front View
3/4 View
①
BrownLine/Hot/Switching
BlueCommon
Green/YellowGround
Black*0-10V (-)
Grey*0-10V (+)

INSTALL NOTE: A-NK6
LANDSCAPE & ARCHITECTURAL LIGHTING | Learn more. Visit fxl.com
3. Product Installation (cont.)
2. Run conduit and/or wiring (code dependent)
to the ideal “knockout(s)” in the construction
sleeve.
3. Use a tool of choice to forcefully remove the
knockout.
4. Connect the conduit/wire runs to the sleeve
with couplings of choice (⁄"-14 NPT).
5. Attach the sleeve cover to protect the interior
during wall nishing using included fasteners.
6. Remove the sleeve cover to resume installation.
7. Connect wiring from housing assembly to the
incoming power lines using the wiring diagram
(see previous section) and approved wire
connectors.
8. Insert the complete housing assembly into the
construction sleeve.
9. Place the housing inside the sleeve and fasten
the screws through the center slots on the le
and right sides. Before fully tightening, rotate
the housing according to the level for ideal
installation.

FX-296-IN 4/20
INSTALL NOTE: A-NK6
LANDSCAPE & ARCHITECTURAL LIGHTING | Learn more. Visit fxl.com
3. Product Installation (cont.)
5. Warranty
STATEMENT OF LIMITED WARRANTY
Hunter Industries Incorporated (“Hunter”) warrants FX Luminaire Line-Voltage Series lighting products to be free of defects in
materials or workmanship under normal use for a period of ve (5) years from the date of invoice. If a defect in a FX Luminaire product
is discovered during the applicable warranty period, Hunter will repair or replace, at its option, the product or the defective part. This
limited warranty does not extend to repairs, adjustments, or replacement of FX Luminaire products or parts resulting from misuse,
negligence, alteration, modication, tampering, or improper installation and/or maintenance of the product. This warranty extends
only to the original installer of the product. If a defect arises in a FX Luminaire product or part during the warranty period, contact the
local authorized manufacturer’s representative. Hunter’s obligation to repair or replace its products as set forth above is the sole and
exclusive warranty set forth by Hunter. There are no other warranties, expressed or implied, including warranties of merchantability
and tness for a particular purpose. Hunter will not be liable to distributor or any other party in strict liability, tort, contract, or any other
manner for damages caused or claimed to be caused as a result of any design or defect in FX Luminaire products, or for any special,
incidental, consequential, or exemplary damages or any nature, including without limitation lost business or prots. Notwithstanding
the foregoing, if for any reason Hunter is found to be liable, in no event shall Hunter’s liability exceed the price of the product which gives
rise to the claim, loss, or damage.
If you have any questions concerning the warranty or its application, please write to:
Customer Service Department
FX Luminaire
1940 Diamond Street
San Marcos, CA 92078 USA
10. Use the included fasteners to attach the
faceplate to the housing.