Gage Bilt GB734V User manual

GB734V
INSTALLATION TOOL
GAGE BILT
MADE IN U.S.A.
GAGE BILT Inc.
44766 Centre Court [phone]
Clinton Twp. MI 48038 [phone] Fax
e-mail: soluti[email protected] / www.gagebilt.com
GAGE BILT TOOLS ARE AVAILABLE WORLDWIDE
E-MAIL US FOR A DISTRIBUTOR NEAR YOU.

2 REV. 8/13
SPECIFICATIONS
Hand Held Weight - 6.25 lbs.
Air pressure req'd - 90-100 p.s.i.
Air consumption - .16 SCF/cycle (4.53 L/cycle)
Hydraulic fluid - Automatic Transmission Fluid,
Dexron® III, or equivalent.
Setting stroke - 1.090"
Rated pull load - 3,000 lbs.
Noise level - 81.5 dB (A)
Vibration - Tested-No hazards found.
TABLE OF CONTENTS
Description Page
Warnings...................................................................................................................................3
Description, Operation and Maintenance...............................................................................4
Filling and Bleeding ...............................................................................................................5
Troubleshooting .......................................................................................................................6
Overhaul, Disassembly and Parts List ...............................................................................7-8
DEXRON® III Oil Safety Data .......................................................................................................9
Nose Assembly Selection Chart ...........................................................................................10
EU Conformity and Warranty ................................................................................................11
1.94 Ø
(49.0mm)
1.36 Ø
(34.5mm)
1.50
(38.1mm)
6.42
(163.0mm)
2.80
(71.2mm)
12.07
(306.5mm)
2.25
(57.2mm)
6.17
(156.7mm)
4.88 Ø
(124mm)
.88 Ø
(22.2mm)
12.81
(325.5mm)
4.78
(121.5mm)
2.60 Ø
(66mm)

3 REV. 8/13
WARNING
Do not pull fastener unless it is placed in an
assembly, pin will eject forcibly when pintail breaks
off. Severe personal injury may result.
WARNING
Do not operate without Stat-O-Seal (S572) and cap
screw (402482). Pressurized hydraulic fluid may
cause severe personal injury.
WARNING
When operating, repairing or overhauling tool, wear
approved eye protection. Do not look in front of
nose assembly or rear of tool when installing
fastener.
WARNING
Always disconnect tool from power before
performing any maintenance to any tool or nose
assembly. Ensure that all connections are proper
and there are no visible leaks from tool or hoses
before connecting to power.
WARNING
Do not operate if deflector, bottle, catcher bag or
vacuum tube is removed or damaged, broken
pintails may eject forcibly from rear of tool. Severe
personal injury may result.
CAUTION
Ensure that nose assembly and tip are properly
matched for the fastener being installed.
CAUTION
Keep Nose Assemblies clean and free of chips and
debris.
WARNING
Be sure there is adequate clearance for tool and
operator's hands before proceeding. Keep fingers
clear of any moving parts. Keep fingers clear from
fasteners and installed materials. Severe personal
injury may result.
WARNING
It is required to use hearing protection. A test was
carried out in a simulated work environment where
the background level was 73.2 DBA. In this
condition the max level was 81.5 DBA. Therefore, it
is required where prolonged use, hearing
protection be used.
CAUTION
Do not use beyond the design intent.
WARNING
Tool must be maintained in a safe working
condition at all times and examined on a regular
daily basis for damage or wear. Any repair should
be done by qualified personnel trained on Gage Bilt
procedures.
SAFETY WARNINGS
WARNING
Where prolonged use is foreseen, it is
recommended a tool balancer be used. Check
suspension device to ensure that it is secure.
WARNING
Do no use tool in explosive atmosphere.
CAUTION
Tool is not to be used as a hammer.
WARNING
Risk of crushing exists if nose assembly is not
attached.
NOTE:
PLEASE READ THIS MANUAL BEFORE SERVICING OR USING THIS TOOL.
REVIEW ALL WARNINGS AND CAUTIONS TO PREVENT
SEVERE PERSONAL INJURY OR DAMAGE THE TOOL.
WARNING
It is recommended tool be operated 50 out of every
60 minutes, where prolonged use is expected.
WARNING
Shock:
It is recommended operator wear a suitable glove
during operation where prolonged use is expected.
WARNING
Air pressure not to exceed 100 psi., except where noted.

4 REV. 8/13
Daily cleaning and lubrication of nose assembly will
greatly reduce downtime and increase life of
components. Using sewing machine oil, or an
equivalent cleaner/lubricant, follow instructions
below.
1. Disconnect tool vacuum line (if equipped).
2. Point nose assembly into oil as shown.
3. Cycle tool 8-10 times and wipe dry.
TORQUE SPECIFICATIONS
Button Head Cap Screws (402479) = 40 inch lbs.
Packing Plug (744118) = 45 foot lbs.
Flexlock Nut (400559) = 40 inch lbs.
End Cap (734111-1) = 45 foot lbs.
Button Head Cap Screws (402482) = 35-40 inch lbs. (Do NOT over-tighten)
DESCRIPTION
WARNING: THE BALANCE OF THIS TOOL IS DESIGNED FOR HORIZONTAL USE AND IS NOT SUITED FOR ANY
OTHER APPLICATIONS. GAGE BILT WILL BE PLEASED TO ADVISE FOR YOUR SPECIFIC
APPLICATION.
The GB734V is a pneumatic-hydraulic tool designed specifically for the efficient installation of a wide range of
blind rivets. It weighs 6.25 lbs. and can be operated in any position with one hand. It has a 1.090" rivet setting
stroke and a rated pull load of 3000 pounds with 90 psi air pressure at the air inlet.
The GB734V riveter operates on a wide range of air pressure, with 90 to 100 psi providing the maximum
efficiency. At 90 psi air pressure, the GB734V does not exceed 81.5 db (A) and consumes 3 cfm at 20 cycles a
minute.
The air inlet is provided with 1/4-18 female pipe threads to accept the users air hose fitting.
UNLESS ORDERED RIVET SPECIFIC (I.E. GB734V/6P), THE STANDARD GB734V IS FURNISHED WITH NOSE
ASSEMBLY 8N-743A-24V AND WITH SPARE NOSE TIP 10204 TO CONVERT TO 6N-743A-24V NOSE
ASSEMBLY. ALL OTHER NOSE TIPS MUST BE ORDERED SEPARATELY. WHEN ORDERING TOOL RIVET
SPECIFIC, PLEASE CONTACT GAGE BILT FOR MORE INFORMATION. (See page 10 for nose assembly
recommendations.)
MAINTENANCE
WARNING: EXCESSIVE CONTACT WITH HYDRAULIC FLUID AND LUBRICANTS SHOULD BE AVOIDED.
WARNING: MAINTENANCE PERSONNEL MUST READ AND UNDERSTAND ALL WARNINGS AND CAUTIONS.
The performance of any tool depends upon good maintenance practices. Following these minimall
requirements for service and care will extend the life of your tool.
*Only use an air supply set at 90-100 psi. equipped with a filter-regulator to prevent wear.
*The tool will eventually lose some hydraulic oil. Keep the hydraulic system full and free of air by
using the air bleeder (704153) on a regular basis.
*Proper care by operator is necessary in maintaining full productivity and reducing downtime. Read all
applicable tool manuals and nose assembly data sheets prior to operating tools.
*Keep nose assemblies, especially jaws, clean and free of chips and debris. Lube jaws and collet surfaces
that jaws ride on with light machine oil.
*For a complete overhaul, tool kit GB740TK is recommended.
CLEANING AND LUBRICATING PROCEDURE
Image may not reflect actual tool

5 REV. 8/13
TROUBLESHOOTING
Providing all maintenance conditions have been met, follow this systematic approach to diagnosis.
1. MORE THAN ONE PULL IS REQUIRED TO BREAK RIVET.
a) Tool needs to be bled. (See filling and bleeding instructions.)
b) Spring has fatigued, replace.
c) Jaws are stripped or packed with chips. Clean or replace.
d) Incorrect nose tip.
2. SLOW OR PARTIAL OPERATION WHEN THE TRIGGER IS DEPRESSED
a) Head Piston Rings (A-289) and (401112) could be worn or damaged. Replace.
b) Piston Rod Rings (S908) and (A-201) could be worn or damaged. Replace.
c) Muffler (744143) or filter inside spool (743142) may be plugged with dirt. Clean thoroughly and back-blow with compressed air.
d) Hole in metering screw in valve spool (743142) may be blocked or damaged. Hole diameter should be .028". Clear and size or
replace.
3. NO OPERATION WHEN TRIGGER IS DEPRESSED
a) Tool seized due to mechanical failure or damaged parts.
4. OIL LEAKAGE
a) DO NOT OPERATE WITH OIL LEAKING FROM TOOL. HIGH PRESSURE OIL MAY CAUSE SEVERE PERSONAL INJURY.
b) Any oil leaking externally should be traced to its source. An o'ring or seal that leaks should be replaced.
5. AIR BYPASS FROM VALVE HOUSING
a) If the spring (744144) breaks or dislodges, air will flow freely through the muffler (744143). Replace or reset. Valve spring
installation tool (744151) is recommended.
b) Check o'rings on valve sleeve (743144), valve spool (743142), and valve plug (744142). If worn or damaged, replace. Valve
sleeve removal tool (744152) is recommended.
6. FASTENER STEM JAMMED IN NOSE ASSEMBLY
a) Nose assembly components require service. DISCONNECT AIR FROM TOOL, remove the nose from the tool and disassemble.
Replace worn or broken parts. Clean the surface the jaws ride on.
b) Stems lodged side by side in the follower. Disassemble, remove stems, and reassemble.
c) Incorrect follower.
7. PINTAIL IS NOT BEING VACCUMED THROUGH.
a) Check vacuum pressure using vacuum gage 703567 (sold separately).
Note: Offset nose assemblies must be check by removing the vacuum line from the nose assembly.
b) Press gage against the vacuum line or nose assembly to create seal.
Optimum vacuum pressure at nose assembly must be between 15-22 in.Hg
FILLING & BLEEDING PROCEDURE:
WARNING DO NOT CYCLE TOOL WITHOUT AIR BLEEDER, OR THE SCREW AND STAT-O-SEAL, INSTALLED IN TOOL HEAD.
SEVERE PERSONAL INJURY MAY RESULT.
CAUTION BEFORE FILLING HANDLE, AIR PISTON SHOULD BE ALL THE WAY DOWN.
`* FILLING & BLEEDING VIDEO AVAILABLE AT: www.gagebilt.com/bleeding.htm
To replace a small amount of oil in the tool, attach the air bleeder and connect tool to air line. Cycle a number of times.
Disconnect air, remove the air bleeder, and reinstall the cap screw. This will insure the removal of any air from the hydraulic
system and its replacement with fluid.
Should it become necessary to completely refill the tool (such as would be required after tool has been dismantled and
reassembled), take the following steps after depressing trigger AND DISCONNECTING THE AIR SUPPLY:
1. Remove head assembly from handle assembly. Slowly push piston completely forward.
2. Fill handle and oil passage on top of handle with automatic transmission fluid, Dexron III or equivalent. When looking
at the top of the handle, the oil passage is the hole that is counterbored for S832 o'ring.
3. Replace head assembly with care, insuring gasket (704129) and o'ring (S832) are properly installed. Tighten cap
screws (402479) uniformly to prevent leakage around gasket.
4. Remove screw (402482) and stat-o-seal (S572) install bleeder bottle (704153) and connect tool to air line, cycle
ten to twenty times to fully circulate fluid through hydraulic system.
5. DISCONNECT AIR FROM TOOL. Remove bleeder bottle (704153) install screw (402482) and stat-o-seal (S572).
Reconnect air and cycle tool 10 more times. Check tool stroke, if stroke doesn’t check .900" min. (See figures below)
.050
1.140

6 REV. 8/13
OVERHAUL
The disassembly and re-assembly procedure can be accomplished by utilizing the following instructions and drawings.
Use extreme care during disassembly and re-assembly not to mar or nick any smooth surface that comes in contact
with seals. Before installing seals, always apply a good lubricant, such as Lubriplate®, to the surfaces. It is
recommended that tool kit (GB740TK) be used to facilitate overhaul. A complete overhaul can be achieved by the use of
Service Kit 734004 which contains a complete set of o'rings, back-up rings, screws, washers and gasket.
WARNING: DEPRESS TRIGGER AND DISCONNECT FROM AIR WITH HEAD PISTON IN THE REAR POSITION BEFORE
OVERHAUL. SEVERE PERSONAL INJURY MAY OCCUR IF AIR HOSE IS NOT DISCONNECTED. USE CAUTION
WHEN FORCING PISTON ROD ASSEMBLY DOWNWARD WITH HEAD CYLINDER ASSEMBLY REMOVED,
HYDRAULIC FLUID WILL EJECT FORCIBLY FROM HANDLE.
704214
STEM CATCHER BAG
704149
PISTON ROD WRENCH
704151
POWER CYLINDER TOOL
704152
SEAL GUIDE
704150
PACKING PLUG WRENCH
704153
BLEEDER BOTTLE
744151
VALVE SPRING
INSTALLATION TOOL
744152
VALVE SLEEVE
REMOVAL TOOL
S1178
VALVE EXTRACTOR
(704214 CATCHER BAG SHOWN ABOVE IS SOLD SEPARATELY)
Part No. Description
704149 Piston Rod Wrench
704150 Packing Plug Wrench
704151 Power Cylinder Tool
704152 Seal Guide
704153 Bleeder Bottle
S1178 Valve Extractor
744151 Valve Spring Installation Tool
744152 Valve Sleeve Removal Tool
GB740TK Service Tool Kit Includes:
HOW TO CLEAN VACUUM REGULATOR
1. Remove vacuum regulator 703515 from hose.
2. Remove (4) S.H.C.S. from front of regulator and disassemble.
3. Clean both pieces in clean mineral spirits and blow dry.
4. Reassemble and connect hoses.
Note: The vacuum regulator may visually appear clean, but still may be contaminated with a thin film, there-
fore, the steps above should be performed to assure best performance.

7 REV. 8/13
HEAD
Remove nose assembly and adapter from tool before attempting disassembly of head assembly.
WARNING: DISPOSE OF HYDRAULIC FLUID IN ACCORDANCE WITH ALL ENVIRONMENTAL LAWS AND REGULATIONS
APPLICABLE TO YOUR AREA.
Remove end cap (734111-1). Push against threaded end of head piston (734107) to slide it out of head
cylinder (734102). Be careful not to damage threads or cause burrs on polished piston rod surface.
The re-assembly sequence is the opposite of disassembly. (See Filling and Bleeding instructions.) Apply
Loctite® #242 and torque the button head cap screws (402479) uniformly to 40 inch lbs. to prevent leakage
around the gasket.
S572 - STAT-O-SEAL
400790 - O'RING
402482 - BUTTON HEAD CAP SCREW
734107 - PISTON
401089 - BACK-UP RING
S834 - O'RING
A-289 - O'RING
401112 - BACK-UP RING
S829 - O'RING
734111-1 - END CAP
S834 - O'RING
734102
HEAD CYLINDER ASSEMBLY
703509 - TUBING (10 FT.)
A-216 - FITTING
A-506 - TEE
A-503
ADAPTER
703589- TUBING (10 FT.)
700440 - FITTING
703515 - VACUUM REGULATOR
703537 - FITTING ASSEMBLY
703506 - BOTTLE, BUSHING
AND CAP ASSEMBLY
(TO 703537 & 700440)
A-216
(TO HANDLE)
A-508 - ADAPTER
703518 - MUFFLER
B
A
(TO A-216 (2)

8 REV. 8/13
HANDLE
To inspect air cylinder bore, remove base cover (744124). Any further disassembly will require removal of the head cylinder (734102)
first. For complete disassembly, start by removing base cover (744124). Next, holding tool upright, remove four button-head cap
screws (402479). Lift head cylinder (734102) from handle (744129) and set aside o'ring (S832) and gasket (704129). Empty all
hydraulic fluid into a container. Place piston rod wrench (704149) down into top of power cylinder (743131), into the hex of piston rod
assy. (744136). While holding this wrench, remove flexlock nut (400559) using a 7/16" socket wrench. Still holding piston rod
wrench, remove air piston (744121) using packing plug wrench (704150), by turning counterclockwise. When air piston is completely
free from piston rod, tap or push on the piston rod wrench to eject air piston from bottom of handle. After removal of air piston, slide
piston rod (744136) back up to the end of its travel. Using packing plug wrench (704150) remove packing plug (744118). With
packing plug removed, power cylinder (743131) can be removed by pushing on power cylinder tool (704151) when inserted into top of
power cylinder.
To reassemble the handle, reverse the above procedure, being certain that all o'rings are properly lubricated before installation.
Torque packing plug (744118) to 45 foot lbs. Attach the seal guide (704152) to the piston rod (744136) and tap the piston rod through
the packing plug (744118). Attach air piston (744121) and flexlock nut (400559) torque flexlock nut to 40 inch lbs. With the piston rod
in the down position, fill oil passage on top of handle with automatic transmission fluid, Dexron III or equivalent, when looking at top
of handle the oil passage is the hole that has a counterbore for (S832) o'ring. Replace gasket (704129) and o'ring (S832), just prior to
replacing head cylinder (734102). (See Filling & Bleeding instructions.)
AIR VALVE
WARNING: DISCONNECT TOOL FROM ITS AIR SOURCE BEFORE DISASSEMBLY.
To disassemble, first disconnect tool from its air source. Remove pin (744149) and muffler (744143). Insert valve extractor (S1178)
into end of valve plug (744142) and pull it out. Using the same procedure, pull out spool (743142). NOTE: It should never be
necessary to remove valve sleeve (744134) unless the ports in the sleeve are plugged from contaminated air. If ports are plugged,
use needle nose pliers to grasp end of spring (744144), turning clockwise and pulling to dislodge from groove in casting. NOTE:
744151 valve spring tool will facilitate the proper installation of the spring (744144), valve sleeve (743144) can be pulled out using
valve sleeve removal tool 744152.
704130 - TRIGGER
704129 - GASKET
S832 - O'RING
A-249 - SWIVEL
744129 - HANDLE
743131 - POWER
403805 - O'RING
S892 - O'RING
S908 - BACK-UP RING
A-201 - O'RING
744136
744149 - PIN
744143 - MUFFLER
400785 - O'RING
744142 - VALVE PLUG
400785 - O'RING
743142 - VALVE SPOOL
400779 - O'RING
744144 - SPRING
743144 - VALVE
400784 - O'RING
A-287 - O'RING
S115 - BACK-UP RING
A-271 - O'RING
744118 - PACKING PLUG
S115 - BACK-UP RING
A-287 - O'RING
S909 - BACK-UP RING
401462 - QUAD RING
S909 - BACK-UP RING
744121 - AIR PISTON
400559 - FLEXLOCK NUT
S12 - O'RING
744124 - BASE COVER
S885 - RETAINING RING
ASSEMBLY
CYLINDER
PISTON ROD ASSEMBLY
(INCLUDES S908 AND A-201)
HEAD CAP SCREW (4)
402479 - BUTTON
SLEEVE
ASSEMBLY
ASSEMBLY

9 REV. 8/13
FIRST AID
Skin: Wash thoroughly with soap and water as soon as possible. Casual contact requires no
immediate attention. If irritation develops, consult a physician.
Ingestion: Seek medical attention immediately. DO NOT INDUCE VOMITING.
Eyes: Flush with copious amounts of water. If irritation develops, consult a physician.
Inhalation: No significant adverse health effects are expected to occur on short term exposure.
Remove from contaminated area. Apply artificial respiration if needed. If unconscious,
consult a physician.
FIRE
Suitable extinguishing media: CO2 dry powder, foam or water fog. DO NOT use water jets.
ENVIRONMENT
Waste disposal: In accordance with all environmental laws and regulations applicable to your area.
Spillage: Prevent entry into drains, sewers and water course. Soak up with diatomaceous earth or
other inert material. Store in appropriate container for disposal.
HANDLING
Eye protection required. Protective gloves recommended. Chemically resistant boots and apron
recommended. Use in well ventilated area.
COMBUSTIBILITY
Slightly combustible when heated above flash point. Will release flammable vapor which can burn in
open or be explosive in confined spaces if exposed to source of ignition.
PROPERTIES
Specific Gravity 0.863
Weight per gallon 7.18
Open flash point >200°C (392°F)
DEXRON® III OIL SAFETY DATA

10 REV. 8/13
XX-703-18V
XX-734A-20V
XX-743A-24V
SEE CHART
SEE CHART
SEE CHART
10757
ANVIL HOLDER
20518
COLLET SEE CHART 405371
SPRING
70820
NUT
SEE
CHART
10935
ANVIL HOLDER
10951
ANVIL HOLDER
28819
COLLET
20867
COLLET
SEE
CHART
SEE
CHART
400777
O'RING
SEE
CHART
405371
SPRING
70820
NUT
50626
SPRING
70820
NUT
SEE
CHART
RIVET DIA. NOSE ASSEMBLY NOSE TIP JAW FOLLOWER DESIGNATION
3/16 AV6-743A-24V
1
10141 30849 703416 AV6
3/16 6C-743A-24V
1
10141-1 30849 703416 6C
BULB-TITE® (STRUCTURAL) RIVET 1/4 BT08-743A-24V
1
10391 30849 703416 BT08
3/16 6KT-743A-24V
1
10263 30849 703416 6KT
1/4 8KT-743A-24V
1
10262 30849 703416 8KT
MA CHINE SCREW RIV ET 5MM MS5M-743A-24V
1
10332 30849 703416 5MM
4MM 5N-703-18V
2 --- MB06
5MM 6N-743A-24V
1
10204 30849 703416 6N
3/16 MB06-734A-20V
2,3
-- - MB06
1/4 MB08-734A-20V
2,3
-- - MB08
3/32 3N-703-18V
2
-- - 3N
1/8 4N-703-18V
2
-- - 4N
5/32 5N-703-18V
2
-- - 5N
3/16 6N-743A-24V
1
10204 30849 703416 6N
1/4 8N-743A-24V
1
10211 30849 703416 8N
3/32 3CEA-703-18V
2
--- 3CEA
1/8 4CEA-703-18V
2
--- 4CEA
5/32 5CEA-703-18V
2 --- 5CEA
3/16 6CEA-743A-24V
1
13473 30849 703416 6CEA
3/32 3CES-703-18V
2 --- 3CES
1/8 4CES-703-18V
2
--- 4CES
5/32 5CES-703-18V
2
--- 5CES
3/16 6CES-743A-24V
1
13477 30849 703416 6CES
1/4 8CES-743A-24V
1
13469 30849 703416 8CES
3/16 6P-743A-24V
1
10167 30849 703416 5SS
1/4 8P-743A-24V
1
10166 30849 703416 6SS
3/16 6T-743A-24V
1
10209 30849 703416 6T
1/4 8T-743A-24V
1
10286 30849 703416 8T
TLR® RIV ET 1/4 8TLR-743A-24V
1
10246 30849 703416 8TLR
3/16 PH6-734A-20V
2,3
-- - PH6
1/4 PH8-734A-20V
2,3
-- - PH8
1) YOU CAN CHANGE THE 743A-24 NOSE ASSEMBLY (INCLUDED WITH TOOL) TO INSTALL OTHER FASTENERS BY PURCHASING
2) NOSE ASSEMBLIES WITH A 734A AND 703-18 DESIGNATION, I.E. 5N-703-18V, MUST BE ORDERED A S COMPLETE NOSE A SSEMBLY .
3) NOSE ASSEMBLIES WITH A 734A DESIGNATION, I.E. PH6-734A-20V, ARE FOR SERRATED STEM RIVETS ONLY. IF YOU ARE PULlING BOTH SMOOTH A ND
SERRATED STEM RIVETS YOU MUST ORDER THE NOSE ASSEMBLY WITH A 743 DESIGNATION, I.E. MGL06-743A-24V.
EXTENDS FROM THE TOOL I.E. -20 = 2.0 INCHES
PROTRUDING HEA
D
SERRA TED STEM
STRUCTURA L RIV ET
NOTE: THE L A ST 2 DIGITS OF THE NOSE A SSEMB L Y REPRESENTS THE L ENGTH THE NOS E
NOSE TIP SHOWN AND USING APPROPRIATE FOLLOWER SHOWN.
T RIV ET®
A V EX ®, KLA M P- TIT E®, T LR® A N D M ONOB OLT® A R E REGIST ERED T RA D EM A R KS OF A V D EL U K LIM IT ED. B U LB -T ITE® IS A R EGISTER ED TRA DEM A R K OF GESIPA F A STEN ERS U SA , IN C. T R IV ET®
IS A R EGISTER ED T RA D EM A R K OF C HER RY A ER OSPA CE F A STEN ERS.
OPEN END
NA IL RIV ET
A V EX® ( 1624 PROTRUDING HEA D)
AVEX (1624 COUNTERSUNKHEAD)
KLA MP-TITE® (STRUCTURA L) RIV ET
MONOBOLT® RIV ET
PLA STIC SPLIT RIV ET
CLOS ED END
NA IL RIV ET
(A LUMINUM MA NDREL)
CLOS ED END
NA IL RIV ET
(STEEL MA NDREL)
MILLIMETER SEAL PLUG
REV. 8/13

11 REV. 8/13
Seller warrants that all goods covered by this catalog will con-
form to applicable specifications and will replace or repair, F.O.B. our
plant, any goods providing defective from faulty workmanship, or material,
for 6 months from date of shipment.
Said warranty to remain in effect if and only if such goods are
used in accordance with all instructions as to maintenance, operation and
use, set forth in manuals and instruction sheets furnished by seller.
Seller obligation under this warranty shall be limited to the repair
or rework of the goods supplied or replacement thereof, at Seller’s option,
and in no case is to exceed the invoice value of said goods. Under no
circumstances will the seller be liable for incidental or consequential dam-
ages or for damages incurred by the buyer or subsequent user in repair-
ing or replacing defective goods or if the goods covered by this warranty
are reworked or subjected to any type of additional processing.
This warranty is void if Seller is not notified in writing of any re-
jections or defects within 6 months after the receipt of the material by the
customer.
THIS WARRANTY IS MADE IN LEIU OF ALL OTHER WARRANTIES
EXPRESSED OR IMPLIED, INCLUDING MERCHANTABILITY.
WARRANTY
DECLARATION OF CONFORMITY
WE DECLARE THAT THE EQUIPMENT SPECIFIED HEREIN
CONFORMS TO THE FOLLOWING STANDARDS AND DIRECTIVES.
EN292 part 1 and part 2
ISO 8662 part 1
ISO 3744
COUNCIL DIRECTIVE: 89/392/EEC, 91/368/EEC
93/44/EEC, 93/68/EEC
EQUIPMENT DESCRIPTION:
GB734V SERIES FASTENER INSTALLATION TOOLS
MANUFACTURER:
GAGE BILT Inc.
SIGNATURE:
NAME: BRIAN LEIGH
PRODUCT MANAGER
CLINTON TWP., MI U.S.A.
MAY 2010
[phone]
GAGE BILT
DEXRON® IS A REGISTERED TRADEMARK OF GENERAL MOTORS CORPORATION. LUBRIPLATE® IS A REGISTERED TRADEMARK OF FISKE BROTHERS REFINING CO. LOCTITE® IS A REGISTERED
TRADEMARK OF HENKEL CORPORATION