Gardner Denver 8000 Series Service manual

SB--7--627
Version 02
January, 2006
OPERATING AND
SERVICE MANUAL
BLOWERS
8000 SERIES
10” -- 22” GEAR DIAMETER

SB--7--627 Page i
MAINTAIN BLOWER RELIABILITY AND PERFORMANCE
WITH GENUINE GARDNER DENVER
PARTS AND SUPPORT SERVICES
Factory genuine parts, manufactured to design
tolerances, are developed for optimum dependability
------ specifically for your blower. Design and material
innovations are born from years of experience with
hundreds of different blower applications. When you
specify factory genuine parts you are assured of receiv-
ing parts that incorporate the most current design
advancements . . . manufactured in our state--of--the--
art blower factory under exacting quality standards.
Your AUTHORIZED DISTRIBUTOR offers all the
backup you require. A worldwide network of authorized
distributors provides the finest product support in the
blower industry.
Your AUTHORIZED DISTRIBUTOR can support your
blower investment with these services:
1. Trained parts technical representatives to assist
you in selecting the correct replacement parts.
2. Complete inventory of new machines and new,
genuine factory parts.
3. A full line of factory tested AEONtPD blower
lubricants specifically formulated for optimum
performance in all blowers.
4. Authorized Distributor service technicians are
factory-trained and skilled in blower maintenance
and repair. They are ready to respond and assist
you by providing fast, expert maintenance and
repair services.
INSTRUCTIONS FOR DETERMINING BLOWER CONFIGURATION
1. Face the blower drive shaft.
2. In a VERTICAL configuration, air flow is horizontal.
3. In a HORIZONTAL configuration, air flow is vertical.
4. In a vertical configuration, a BOTTOM HAND
exists when the drive shaft is below the horizontal
center line of the blower. A TOP HAND exists
when the drive shaft is above the horizontal center
line of the blower.
5. In a horizontal configuration, a RIGHT HAND
exists when the drive shaft is to the right of the
vertical center line of the blower. A LEFT HAND
exists when the drive shaft is to the left of the
vertical center line of the blower.
INSTRUCTIONS FOR ORDERING REPAIR PARTS
For pricing and ordering information, contact your nearest AUTHORIZED FACTORY DISTRIBUTOR.
When ordering parts, specify Blower MODEL and SERIAL NUMBER (see nameplate on unit).
Rely upon the knowledge and experience of your AUTHORIZED DISTRIBUTOR and let them assist you in making
the proper parts selection for your blower.
For the location of your local authorized Gardner Denver Blower distributor refer to the yellow pages of your
phone directory, check the Web site at www.gardnerdenver.com or contact:
Gardner Denver Compressor Division
1800 Gardner Expressway
Quincy, IL 62305
Phone: [phone]
Fax: [phone]
2
4400 Morris Park Drive Web: www.suncopowder.com
Charlotte, NC 28227 Email: [e-mail]
Phone: [phone] Fax: [phone]

SB--7--627 Page ii
FOREWORD
SutorbiltRblowers are the result of advanced engineering and skilled manufacturing. To be assured of receiving
maximum service from this machine the owner must exercise care in its operation and maintenance. This book is
written to give the operator and maintenance department essential information for day-to-day operation,
maintenance and adjustment. Careful adherence to these instructions will result in economical operation and mini-
mum downtime.
Danger is used to indicate the presence of a hazard which will cause severe personal
injury, death, or substantial property damage if the warning is ignored.
Warning is used to indicate the presence of a hazard which can cause severe
personal injury, death, or substantial property damage if the warning is ignored.
Caution is used to indicate the presence of a hazard which will or can cause minor
personal injury or property damage if the warning is ignored.
Notice is used to notify people of installation, operation or maintenance information
which is important but not hazard--related.
For Part List information, see:
Gear Diameter Parts List
10” SB--7--528..................................
12” SB--7--529..................................
14” SB--7--530..................................
16” SB--7--531..................................
18” SB--7--532..................................
20” SB--7--533..................................
22” SB--7--534..................................

SB--7--627 Page iii
SAFETY PRECAUTIONS
Safety is everybody’s business and is based on your use of good common sense. All situations or circumstances
cannot always be predicted and covered by established rules. Therefore, use your past experience, watch out for
safety hazards and be cautious. Some general safety precautions are given below:
Failure to observe these notices could result in injury to or death of personnel.
DKeep fingers and clothing away from blower inlet and discharge ports,
revolving belts, sheaves, drive coupling, etc.
DDo not use the air discharge from this unit for breathing -- not suitable for
human consumption.
DDo not loosen or remove the oil filler plug, drain plugs, covers, or break any
connections, etc., in the blower air or oil system until the unit is shut down
and the air pressure has been relieved.
DElectrical shock can and may be fatal.
DBlower unit must be grounded in accordance with the National Electrical
Code.
DOpen main disconnect switch, tag and lockout before working on the control.
DDisconnect the blower unit from its power source, tag and lockout before
working on the unit -- the machine may be automatically controlled and may
start at any time.
Failure to observe these notices could result in damage to equipment.
DStop the unit if any repairs or adjustments on or around the blower are
required.
DDisconnect the blower unit from its power source, tag and lockout before
working on the unit -- the machine may be automatically controlled and may
start at any time.
DDo not exceed the rated maximum speed shown on the nameplate.
DDo not operate unit if safety devices are not operating properly. Check
periodically. Never bypass safety devices.

SB--7--627 Page iv
TABLE OF CONTENTS
Page
Maintain Blower Reliability and Performance with Genuine Gardner Denver Parts and Support Services i......
Instructions for Ordering Repair Parts i................................................................
Instructions for Determining Blower Configuration i......................................................
Foreword ii.........................................................................................
Safety Precautions iii...............................................................................
Index v............................................................................................
List of Illustrations vi................................................................................
Introduction, Your Key To Trouble Free Service 1........................................................
Operating Principles 1...............................................................................
Section 1, Equipment Check 2........................................................................
Section 2, Installation 3..............................................................................
Section 3, Pre--Start 6...............................................................................
Section 4, Operation 9...............................................................................
Section 5, Maintenance 15...........................................................................
Section 6, Repair and Replacement 19.................................................................
Warranty Last Page.................................................................................