Garlando TOORX MOTION User manual

Ed : Rev : Cod:
INSTRUCTION
08/20 GRLDTOORXMOTION00

2
When you open the carton, and you will find the below parts in the carton
PART LIST：
NO. DES. Specification Nos
.. NO. DES. Specification Nos
.
1 Main frame 1 64 Lock washer 8 6
12 5#Allen wrench 1 70 Bolt M8*45 2
19 Bolt 4.2*19 2 71 Safety key 1
37 IPAD rack 1 72 Silicone oil 1
51 Bolt M8*16 4 74 MP3 wire option 1
59 Left base cover 1 78 Wrench with screw
driver 1
60 Right base cover 1
FIXING TOOLS:
5# Allen Wrench 5mm 1PC
Wrench with screw driver S=13/14/15 1PC
Notice: Do not get through power before complete assembly

3
Assembly Instructions
STEP 1：
STEP 2：
Open the carton, get out the above
spare parts, and put the Main Frame
onto the level ground.
Holding the computer frame and
uprights, use the 5# Allen wrench to
lock the computer to the upright tube
tight by bolt (51) and lock washer（64）
Notice: do not press wires inside the
tube and check if wires are connected
well. Support the upright with hand to
avoid computer & upright falling down .

4
STEP 3：
STEP 4
1. Pull up the uprights as left
picture.
Notice: Support the upright with
hand to avoid falling down to have
any hurt.
1、Use 5# Allen wrench(12) ，firstly
lock right upright onto base
frame by bolt(70) and lock
washer （64 ）, then lock right
upright onto base by bolt (51)
and lock washer (64).
2、The left upright assembly is the
same as right upright.
Notice: Please always support the
upright with hand during assembly
to avoid falling down to have any
hurt.

5
STEP 5
STEP 6
Please make sure all parts have been fixed properly. Before you use the treadmill,
please read the instruction carefully
Use wrench with screw driver(78)
to lock the left base cover(59)
onto the base frame with bolt (19).
The right side can be assembled
referring to the left side.
NOTICE: the base cover should
buckle into the base frame
vigorously.
1. Push the IPAD rack(37) into the
computer(35).
2. Put the safety key(71) on the
computer and start your exercise.

6
Folding Instruction
Pulling up:
Pulling down:
Pull up the base frame at position A,
till hearing the sound that the air
pressure bar B is locked into the
round tube
Support place A with hand , kick the
place of air pressure bar, then the
main frame will fall down
automatically ( Please keep anybody
and any pet away the machine when
falling down)

7
Technical Parameter
BUILT UP
SIZE(mm)
1476*1170*649mm
POWER
As the rating label showing
FOLDABLE
SIZE(mm)
760*1300*649mm
Maximum output
power
As the rating label showing
RUNNING BOARD
SIZE(mm)
400*1200
SPEED RANGE
0.8-12KM/H
NET WEIGHT
43KG
1 LCD WINDOW
WITH BLUE
BACKGROUND
Speed, time, distance, Calories, Pulse
Grounding Methods
This product must be grounded. If it should malfunction or breakdown, grounding provides
a path of least resistance for electric current to reduce the risk of electric shock. This
product is equipped with a cord having an equipment-grounding conductor and a
grounding plug. The plug must be plugged into an appropriate outlet that is properly
installed and grounded in accordance with all local codes and ordinances.
DANGER –Improper connection of the equipment-grounding conductor can result in
a risk of electric shock. Check with a qualified electrician or serviceman if you are in doubt
as to whether the product is properly grounded. Do not modify the plug provided with the
product – if it will not fit the outlet, have a proper outlet installed by a qualified electrician.
This product is for use on a nominal 220-240/100-120 volt circuit and has a grounding plug that
looks like the plug illustrated in sketch A in following figure. Make that the product is
connected to an outlet having the same configuration as the plug. No adapter should be
used with this product.(The below picture is just for reference，the actual plug and jack is depends
on import country)

8
Operation Guide
OVERVIEW
2. SHOWING
SPEED：Display the speed,
TIME：Display the time
DIST. Display the distance
CAL/PULSE：Display the calories/heart rate
3. BUTTON FUNCTION
“PROGRAM” button: Press this button to choose program from manual mode—P1----P15---FAT;
“MODE” button: When machine in ready state, press this button to choose the mode: mode-time
count down, mode-distance count down, mode-calories count down; When FAT
state, press this button to choose: “ SEX “, “ AGE”, “ HEIGHT”, “ WEIGHT”.
“START” button: Press this button to start the machine, the machine will run at the lowest speed or at
the speed of default program after 3 seconds time count down;
“STOP” button: Press this button to stop the machine, the machine will stop smoothly;
SPEED▲、▼: Adjust the speed. Press the button to adjust the speed when running, and adjust the
data when stop;
SPEED（2,4,6,8,10,12）： Adjust the speed quickly
SPEED+/-: Adjust the speed quickly.
4. MAIN FUNCTION:
Turn on the power, all the windows lit 2 seconds, and then enter the manual mode.
4. 1. Start-up quickly(Manual):
Get through power attach the safety key. After 3 seconds countdown, the treadmill starting and
running from the lowest speed, add and subtract by SPEED button to adjust the speed . Please press
the stop button or off the safety key directly to stop.
4. 2. Countdown mode
Press the ‘MODE’ button, it can choose time countdown mode, distance countdown mode, calories
countdown mode, and the window will show the default data and glitter. At the same time, press
SPEED▲/▼ to set the data. Press ‘START’ button, the machine will run at the lowest speed, you can press

9
SPEED ▲/▼ to change the speed. When it counts down to 0, the machine will stop smoothly. Certainly,
you can press ‘STOP’ button or take out the safety key from the console to stop the machine.
4. 3. Preset programs:
Press ‘PROG’ button to choose the inner install program from P1----P15. When set the program,
the time window will show default data and glitter, press SPEED button to set the running time. Each
program has been divided into 20 section, each exercise time=the setting time/20. Press ‘START’, the
machine will run at the first section speed. When the section is over, it will enter into next section
automatically, the speed will change as next section data. When finish one program, the machine will
stop smoothly. During the running, you can change the speed and incline by the SPEED ▲/▼whenever,
when the program enter next sect will come back to the current speed. And you can press ‘STOP’ or
take out the safety key to stop the machine whenever.
5. HEART RATE:
When holding the hand pulse by two hands, the pulse window will show your heart rate after 5
seconds. In order to get the heart rate exactly, please do a test when the machine stop and hold the
hand pulse more than 30 seconds. The heart rate data is just for reference cannot be as the
medical data.
6. BODY FAT TEST
Press ‘PROGRAM’ button under ready condition, till ‘FAT’ show in the speed window. ‘FAT’ is body
fat test mode. Press ‘ MODE’ to choose parameter ‘ SEX / AGE / HEIGHT / WEIGHT’, and TIME/DIST
window will show “F1”，“F2”、“F3”“F4". When set each parameter, press SPEED ▲/▼ to adjust the data,
and CAL/PULSE window will show the data and press ‘MODE’ button to finish, and the window will
show“F5” and“---” enter into ready condition. Hold the handle pulse with two hands, it will show your BMI
data after 5 seconds.
6.1 Data display and set range
6.2 Body fat index comparison
Body fat index（BMI）
Obesity level
<19
Too thin
19--26
normal
26--30
overweight
>30
Too fat
default
range
mark
SEX（F1）
0（MALE）
0—1
0= MALE 1= FEMALE
AGE（F2）
25
10—99
HEIGHT（F3）
170CM
100-240CM
WEIGHT（F4）
70KG
20-160KG

10
7.USB FUNCTION( Option)：
When treadmill is power on, you may insert any USB memory stick which contains audio files. The
computer will detect the audio files on the memory stick and play the music directly.
8.MP3 FUNCTION( Option):
When the power on, Contacting the external MP3 equipment, the computer will play. The voice is
adjustable from operate the external MP3 equipment, the voice should be adjusted on the proper section
to protect the computer loudhailer.
9.Bluetooth speaker function( Option):
Connect the mobile phone Bluetooth with the Bluetooth speaker on the treadmill, after success of the
connection, you can use the phone to play songs by Bluetooth speaker.
10. SLEEP FUNCTION:
A. Stop for more than 10 minutes without any operation, the system completed all showed off into the
body of sleep sate.
B. Press any key to wake up console under sleep status.
11. Safety key function:
Take away the safety key anytime will stop the machine, all data will return to 0, all window will
display
“---”. All operation will be workable when the safety key is on.
12．Exercise parameter and setting
Display range
Default data
Default
Setting range
Speed (KM/H)
0.8KM/H-12.0KM/H
--------
--------
-------------
Time (MIN:SEC)
0:00—99:59
30:00
30:00
5:00---99:00
Distance (KM)
0.00—99.9
1.0
--------
0.50—99.9
Calories
0Kcl—999Kcl
50Kcl
--------
10Kcl—990Kcl

11
programs table：
TIME
PROGRAM
Setting time/20= interval running time
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
P1
SPEED
2
3
3
4
5
3
4
5
5
3
4
5
4
4
4
2
3
3
5
3
P2
SPEED
2
4
4
5
6
4
6
6
6
4
5
6
4
4
4
2
2
5
4
2
P3
SPEED
2
4
4
6
6
4
7
7
7
4
7
7
4
4
4
2
4
5
3
2
P4
SPEED
3
5
5
6
7
7
5
7
7
8
8
5
9
5
5
6
6
4
4
3
P5
SPEED
2
4
4
5
6
7
7
5
6
7
8
8
5
4
3
3
6
5
4
2
P6
SPEED
2
4
4
4
5
6
8
8
6
7
8
8
6
4
4
2
5
4
3
2
P7
SPEED
2
3
3
3
4
5
3
4
5
3
4
5
3
3
3
6
6
5
3
3
P8
SPEED
2
3
3
6
7
7
4
6
7
4
6
7
4
4
4
2
3
4
4
2
P9
SPEED
2
4
4
7
7
4
7
8
4
8
9
9
4
4
4
5
6
3
3
2
P10
SPEED
2
4
5
6
7
5
4
6
8
8
6
6
5
4
4
2
4
4
3
3
P11
SPEED
2
5
8
10
7
7
10
10
7
7
10
10
5
5
9
9
5
5
4
3
P12
SPEED
3
4
9
9
5
9
5
8
5
9
7
5
5
7
9
9
5
7
6
3
P13
SPEED
3
6
7
5
9
9
7
5
5
7
9
5
8
5
9
5
9
9
4
3
P14
SPEED
2
2
4
5
6
5
4
3
2
1
2
3
4
5
6
5
4
3
2
1
P15
SPEED
2
4
6
8
6
6
4
4
2
2
2
4
6
8
6
6
4
4
2
2

14
Running Belt Adjustment
WARNING: ALWAYS UNPLUG THE TREADMILL FROM THE ELECTRICAL OUTLET BEFORE
CLEANING OR SERVICING THE UNIT.
Clean: General cleaning the unit will greatly prolong the treadmill.
Keep treadmill clean by dusting regularly. Be sure to clean the exposed part of the deck on either side of
the walking belt and also the side rails. This reduces the build up of foreign material underneath the
walking belt by wearing the clean running shoes.
Warning: Always unplug the treadmill from the electrical outlet before removing the motor cover. At least
once a year remove the motor cover and vacuum under the motor cover.
RUNNING BELT AND DECK LUBRICATION
This treadmill is equipped with a pre-lubricated, low maintenance deck system. The belt/ deck friction
may play a major role in the function and life of your treadmill, thus requiring periodic lubrication. We
recommend
a periodic inspection of the deck. You need contact with our service center if you find the damage of the
deck.
We recommend lubrication of the deck according to the following timetable:
Light user (less than 3 hours/ week) annually
Medium user (3-5 hours/ week) every six months
Heavy user (more than 5 hours/ week) every three months
We recommend that you buy the lubrication from our distributor or directly to our company.
Attention: Any repair need the professional technician.
1, We suggest that you should switch off the power for 10 minutes after keep running 2hours, so that it’s
good for maintain the treadmill.
2,For avoiding the slipping during running , the belt should be not too loose; for avoiding the more
abrasion between the roller and belt and maintain the machine’s good running ,the belt should be not too
tight. You can adjust the distance between deck and belt , the belt should be away from the deck about
50-75mm on both sides, if the best not too tight and loose.

15
Center The Running Belt
Place treadmill on a level surface. Run
Treadmill at approximately 6-8KM/H,
checking the running condition.
If the belt has drifted to the right, pull out of
the save clock and switch, turn the right
adjusting bolt 1/4 turn clockwise, then start
running until centering the belt. PIC A
If the belt has drifted to the left ,pull out of the
safety clock and switch, turn the left adjusting
bolt 1/4 turn clockwise ,then start running until
centering the belt .PIC B
Timely adjust the tightness of the belt ,for the
looseness after a period of time running. Pull
out of the safety clock and switch , turn the
left and right adjusting bolt 1/4 turn
clockwise ,then re-start running, confirm the
belt-tightness until the belt be right tightness.
PIC C

16
EXPLODED DRAWING

17
PARTS LIST
No.
Item
Spec.
Qty.
No.
Item
Spec.
Qty.
1
Main frame
1
43
Barb cushion
2
2
Base frame
1
44
Magnetic ring
1
3
Left upright tube
1
1
45
Brown single wire
1
4
Right upright tube
1
46
Bolt
M8*25
3
5
Computer bracket
1
47
Lock nut
M6
10
6
Bolt
ST4.2*25
4
48
Bolt
ST4.2*30
4
7
Rubber pad
4
49
Motor bottom cover
1
8
Lock washer
10
2
50
Barb cushion
2
9
Front roller
1
51
Bolt
M8*16
4
10
Rear roller
1
52
Bolt
M8*40
2
11
Cylinder
1
53
Bolt
M8*42
3
12
5#Allen wrench
5mm
1
54
Bolt
M10*55
2
13
DC motor
1
55
Lock washer C level
8
2
14
Running board
1
56
Bolt
M6*55
1
15
Bolt
M6*37
4
57
Bolt
M5*8
5
16
Adjustable pad
2
58
Lock nut
M8
6
17
Inclined tube plug
2
59
Left base cover
1
18
Motor cover
1
60
Right base cover
1
19
Bolt
ST4.2*19
2
61
Running board strengthen tube
2
20
Side rial
2
62
strengthen tube cushion
275*20*3
4
21
Right back end cap
1
63
Lock washer
5
2
22
Left back end cap
1
64
Lock washer
8
12
23
Fixed plug
2
65
Lock washer
6
3
24
Motor belt
1
66
Isolation nylon pad
φ23*φ10.5*2
4
25
Power wire buckle
1
67
Spring washer
8
2
26
Running belt
1
68
Overload protector
1
27
Foot pad
4
69
Bolt
M6*30
4
28
Ring protector plug B
2
70
Bolt
M8*45
4
29
Moving wheel
2
71
Safety key
1
30
Bolt
M6*37
2
72
Silicone oil
1
31
Standard power
wire
1
73
Spring washer
5
2
32
Switch
1
74
MP3 washer
option
1
33
Foam
2
75
Bolt
4.2*15
4
34
Bolt
ST4.2*13
11
76
Bolt
ST4.2*45
4

18
35
Computer top cover
1
77
Bolt
ST4.2*9.5
4
36
Computer bottom
cover
1
78
Wrench with screw driver
1
37
IP rack
1
79
Bolt
ST4.2*12
8
38
Speed +/-
1
80
Bolt
M8*12
2
39
Start/stop
1
81
Bolt
M6*65
2
40
Control board
1
41
Computer bottom
cover
1
42
Computer top wire
1

GARLANDO SPA
Via Regione Piemonte, 32 - Zona Industriale D1
15068 - Pozzolo Formigaro (AL) - Italy
www.toorx.it - [e-mail]