Garmin ZUMO Zumo 400 Assembly instructions


Warning: The terms of the Garmin Warranty require that the power cable with bare wire leads be
installed by experienced installers having the proper knowledge of automotive electrical systems and
skill in the use of special tools or hardware required for installation.
1: Connect Power to the Mount
Select a suitable and secure location to mount the zūmo on your motorcycle based on available
power sources and safe cable routing.
Bare wires with
inline fuse for
power connection
Power connector
About connecting audio
Standard jacks for microphone (2.5 mm) and audio out (3.5 mm) are located on the left side of
the mount (under a weather cap). When connecting your audio system to the zūmo, be sure to
consider the pathways needed to route the necessary cables. For more information, refer to the
zūmo 400/450 Quick Reference Guide and the zūmo 400/450 Owner’s Manual on disk.
2: Install the Handlebar Base
The zūmo includes parts for two handlebar installation solutions. Custom mounts can require
additional hardware (www.ram-mount.com).
A) To install the U-bolt and handlebar base:
1. Place the U-bolt around the handlebar, and thread
the ends through the handlebar base.
2. Tighten the nuts to secure the base. Do not
overtighten.

note: The recommended torque is 50in-lb
(5.7 N-m). Do not exceed maximum torque of
80in-lb (9 N-m).
B) To install the handlebar base to
the clutch/brake clamp bracket:

note: Both 1/4” standard and M6
bolts are included. Match the size of
the factory bolts on your clutch/
brake clamp bracket.
1. Remove the two factory bolts on your
clutch/brake clamp bracket.
2. Thread the new bolts through the handlebar base, spacers, and clamp bracket.
3. Tighten the bolts to secure the base.
zūmo™ 400/450 InstallatIon sheet
Clutch/brake
clamp bracket
Handlebar
base
Spacers
Handlebar base
Handlebar
U-bolt
Garmin® is a trademark of Garmin Ltd. or its subsidiaries, registered in the USA and other countries. zūmo™is a
trademark of Garmin Ltd. or its subsidiaries. These trademarks may not be used without the express permission of
Garmin.
March 2007 Part Number 190-00778-03 Rev. B Printed in Taiwan

3: Attach the Base Plate to
the zūmo Mount
1. ThreadtheM4x40mmatheadbolts
and nuts to attach the base plate to the
zūmomount.
2. Tighten the nuts to secure the base plate.
4: Attach the Base Plate to
the Handlebar
Base
1. Align the ball of the
handlebar base and the
ball of the base plate with
the double-socket arm.
2. Tighten the knob slightly.
3. Adjust for better viewing
and operation.
4. Tighten the knob to
secure the mount.
5: Install the zūmo
in the Mount
1. Plug the power cable into
thezūmomount.Forabetter
seal, tighten the screws on
the power connector.
2. Fliptheleverup.
3. Fliptheweathercapdown
and under (magnetic).
4. Placethezūmointothe
mount,andipthelever
down.
5. Tighten the security screw.
About the Security
Screwdriver
Use the security screw to better
secure the zūmo to the mount.
You can connect the screwdriver
to your key chain for easy access.
To remove the zūmo from the mount:
1. Loosen the security screw.
2. Flipuptheleveronthemount.
3. Liftoutthezūmo.
tiP: When your zūmo is not in the mount, use the
weather cap to prevent damage to the connector.
Lever
zūmo mount
Power
cable
Security screw
More
Information
For more information about the
zūmo, refer to the zūmo 400/450
Owner’s Manual on disk.
See the Important Safety and
Product Information guide for
product warnings and legal
information.
zūmo mount
Base plate
Weather cap
Knob
Double-socket arm
Handlebar base
zūmo mount Base plate
Power socket
Mini-USB
port
Weather cap
Security screwdriver