Minimum Clearance Other Than Alcove or Closet Installation
0LQLPXPFOHDUDQFHWRFRPEXVWLEOHVXUIDFHVDQGIRUDLURSHQLQJDUHLQFOHDUDQFHERWKVLGHVDQGLQUHDU
Consideration must be given to provide adequate clearance for installation and service.
1PREPARING FOR INSTALLATION
OF NEW DRYER
7,3,QVWDOO\RXUGU\HUEHIRUHLQVWDOOLQJ\RXUZDVKHU
This will allow better access when installing dryer
H[KDXVW
DISCONNECTING GAS
WARNING - NEVER REUSE OLD
)/(;,%/(&211(&7256
7KHXVHRIROGÀH[LEOHFRQQHFWRUVFDQFDXVHOHDNVDQG
SHUVRQDO LQMXU\ $OZD\V XVH QHZ ÀH[LEOH FRQQHFWRUV
when installing gas appliances.
REMOVING LINT FROM WALL EXHAUST
OPENING
• Remove and discard existing plastic or metal foil transi
tion duct and replace with UL listed transition duct.
INTERNAL DUCT
OPENING CHECK THAT EXHAUST
HOOD DAMPER OPENS
AND CLOSES FREELY.
WALL
TILT THE DRYER SIDEWAYS
AND REMOVE THE FOAM
SHIPPING PADS BY
PULLING AT THE SIDES
AND BREAKING THEM
AWAY FROM THE DRYER
LEGS. BE SURE TO
REMOVE ALL OF THE
FOAM PIECES AROUND
THE LEGS.
TURN GAS
SHUT-OFF
VALVE TO THE
OFF POSITION.
DISCONNECT AND DISCARD OLD
FLEXIBLE GAS CONNECTOR AND
OLD DUCTING MATERIAL.
REPLACE WITH NEW CSA(AGA)
APPROVED FLEXIBLE GAS LINE
CONNECTOR AND UL APPROVED
TRANSITION DUCT.
GAS REQUIREMENTS
WARNING
• Installation must conform to local codes and ordinances,or
in their absence, the NATIONAL FUEL GAS CODE,ANSI Z223.
• 7KLVJDVGU\HULVHTXLSSHGZLWKD9DOYH%XUQHU$VVHPEO\IRU
XVHRQO\ZLWKQDWXUDOJDV8VLQJFRQYHUVLRQNLW:(;
your local service organization can convert this dryer for use
ZLWKSURSDQH /3JDV $// &219(56,2160867 %(0$'(
%< 3523(5/< 75$,1(' $1' 48$/,),(' 3(56211(/ $1'
IN ACCORDANCE WITH LOCAL CODES AND ORDINANCE
5(48,5(0(176
• The dryer must be disconnected from the gas supply piping
system during any pressure testing of that system at a test
SUHVVXUHLQH[FHVVRI36,.3D
• The dryer must be isolated from the gas supply piping
V\VWHPE\FORVLQJWKHHTXLSPHQWVKXWRȺYDOYHGXULQJDQ\
pressure testing of the gas supply piping of test pressure
HTXDOWRRUOHVVWKDQ36,.3D
DRYER GAS SUPPLY CONNECTION
• $ LQ 1DWLRQDO 3LSH 7DSHU WKUHDG SOXJJHG WDSSLQJ
accessible for test gauge connection, must be installed
immediately upstream of the gas supply connection to
the dryer. Contact your local gas utility should you have
questions on the installation of the plugged tapping.
• 6XSSO\OLQHLVWREHLQULJLGSLSHDQGHTXLSSHGZLWKDQ
DFFHVVLEOH VKXWRȺ ZLWKLQ IW RI DQG LQ WKH VDPH URRP
with the dryer.
• Use pipe thread sealer compound appropriate for natural
RU/3JDVRUXVH7HÀRQWDSH
• <RX PXVW XVH ZLWK WKLV GU\HU D ÀH[LEOH PHWDO FRQQHFWRU
OLVWHGFRQQHFWRU$16,=&6$7KHOHQJWKRIWKH
connect shall not exceed 3 ft.
• &RQQHFWÀH[LEOHPHWDOFRQQHFWRUWRGU\HUDQGJDVVXSSO\
• 2SHQVKXWRȺYDOYH
• Gas clothes dryers input ratings are based on sea level
operation and need not be adjusted for operation at or
below 2000 ft. elevation.
For operation at elevations above 2000 ft., input ratings
VKRXOGEHUHGXFHGDWDUDWHRISHUFHQWIRUHDFKIW
above sea level.
• Installation must conform to local codes and ordinances or,
in their absence, the NATIONAL FUEL GAS CODE, ANSI Z223.
ADJUSTING FOR ELEVATION
2"
2-5/8" 3/8" NPT MALE THREAD GAS SUPPLY
NOTE: Add to vertical dimension
the distance between cabinet
bottom to floor.
Installation Instructions
2