GE ZGU364 User manual

Installation
Instructions
36" and 48"
Professional Rangetops
Tables de cuisson
professionnelles de 36" (91 cm)
et de 48" (122 cm)
Instructions d'installation
Lo section fronqoise commence 6 Io poge 18
Estufas profesionales
de 36" (91 cm) g 48" (122 cm)
Instrucciones de instoloci6n
Lo secci6n en espo6ol empiezo en Io p6gino 34
131-10691 I
04-08JR

Safety Information
BEFORE YOU BEGIN
Read these instructions completely and carefully.
•IMPORTANT- savetheseinstructionsfor
local inspector's use.
•IM PORTANT- Observe allgoverning
codes and ordinances.
• Note to Installer- Be sure to leave these
instructions with the Consumer.
• Note to Consumer- Keep these instructions
with gour Owner's Manual for future reference.
• Completion Time- 1to 3 hours.
• Proper installation is the responsibility of the
installer. Product failure due to improper
installation is not covered under the warranty.
See Owner's Manual for warrantg information.
WARNING
This appliance must be properlg grounded.
See "Electric Supplg."
For Monogram local service in gour area,
1.800.444.1845.
For Monogram Service in Canada, call
1.800.561.3344.
For Monogram Parts and Accessories, call
1.800.626.2002.
If you received o damaged rangetop, gou should
contact your dealer.
In the Commonwealth of Massachusetts:
_ This product must be installed bg a licensed
plumber or gas fitter.
, When using ball tgpe gas shut off valves, theg
shall be T-handle tgpe.
, A flexible gas connector, when used, must not
exceed 3 feet.
Vent hood Combinations:
It is recommended that these rangetops be installed
in conjunction with a suitable overhead vent hood.
Install o hood with at least 1200 CFM above a 48"
wide rangetop.
Install o hood with at least 600 CFM above a 36"
rangetop.
Due to the high heat capacity of this unit, particular
attention should be paid to the hood and ductwork
installation to assure it meets local building codes.
WARNING:
Clearances to horizontal surfaces above the
rangetop, measured to the cooking surface:
. Installations without a hood require 48" minimum
to combustibles.
A custom hood installation with exposed
horizontal combustibles surfaces must have
an Auto-On feature.
For other installations with a hood, refer to hood
installation instructions for specific hood
clearances.
-&CAUTION:
These rangetops are extremely heavy. Due to the
weight and size of the rangetop and to reduce the
risk of personal injury or damage to the product:
TWO PEOPLEARE REQUIRED FOR PROPER
INSTALLATION.
Installation must conform with local codes. In the
absence of local codes, the rangetop must complg
with the National Fuel Gas Code, ANSIZ223.1/
NFPA 54, latest edition and National Electrical Code
ANSI/NFPA 70 latest addition. In Canada, installation
must conform with the current Natural Gas
Installation Code, CAN/CGA-B149.1 or the current
Propane Installation Code, CAN/CGA-B149.2, and
with local codes where applicable. This rangetop has
been design-certified bg CSA International according
to ANSI Z21.1, latest edition and Canadian Gas
Association according to CAN/CGA-I.1 latest edition.
Leak testing of the appliance shall be conducted
according to the manufacturer's instructions.

Design Information
CONTENTS
Design Information
Models Available ......................................................................3
Backsplash Accessories ......................................................3
Product Dimensions and Clearances
for 48" Wide Models ..............................................................4
Product Dimensions and Clearances
for 36" Wide Models ..............................................................5
Installation Options ..............................................................6
Installation Preparation
Tools and Materials Required ..........................................7
Power Supplg Locations ....................................................7
Remove Packaging ................................................................8
Installation Instructions
Step 1, Cut the Countertop Opening ..............................9
Step 2, Install the Rangetop ............................................10
Step 3, Connect Rangetop to Gas ................................10
Step 4, Connect Electrical ................................................11
Step 5, Check Burners ......................................................11
Finalize Installation ..............................................................11
Installation Checklist ..........................................................11
Install the Rangetop Backsplash Accessorg ..........12
Install the Adjustable
Backsplash Accessorg ................................................13, 14
Gas Conversion ..............................................................15, 18
MODELS AVAILABLE
Monogram rangetops are factorg set for natural
gas or LP gas. Order the model for gour installation
situation.
48" Natural Gas Models:
ZGU484NG - 4 gas burners, grill and griddle
ZGU486NR - 6 gas burners and grill
ZGU486ND - 6 gas burners and griddle
48" LP Gas Models:
ZGU484LG - 4 gas burners, grill and griddle
ZGU486LR - 6 gas burners and grill
ZGU486LD - 6 gas burners and griddle
36" Natural Gas Models:
ZGU364ND - 4 gas burners and griddle
ZGU364NR- 4 gas burners and grill
ZGU366N - 6 gas burners
36" LP Gas Models:
ZGU364LG - 4 gas burners and griddle
ZGU364LR - 4 gas burners and grill
ZGU366L- 6 gas burners
BACKSPLASH ACCESSORIES
All models require 12" minimum clearance
to a vertical combustible surface at the rear.
If clearance is less than 12", the entire surface
of the back wall above the countertop and the full
width of the rangetop must be protected bg a
backsplash. The backsplash must be constructed
of non-combustible material, such as metal,
ceramic tile, brick, marble or other stone.
Two Backsplash Accessories Available:
, The 12" high stainless steel backsplash accessorg
is available. Use this backsplash in combination
with a custom, non-combustible backsplash built
begond the 12" height. The combined height
of the backsplash accessorg and the custom
backsplash must reach the bottom of a hood,
or when there is no hood, to 48" above
the cooking surface.
, An adjustable 30" to 36" high backsplash with shelf
is also available. This backsplash fills in the space
between the top of the rangetop and the bottom
of the hood. The shelf is positioned so that
heat lamps from the bottom of a Monogram
professional hood are directed towards the shelf.
12"HighBacksplash
ZX12B48PSS,for 48"wide rangetops
ZX12B36PSS,for 36"wide rangetops
30"to36"AdjustableHeightBacksplash
With Shelf
ZXADJB48PSS,for48"widerangetops
ZXADJB36PSS,for36"widerangetops

Design Information
PRODUCT DIMENSIONS AND CLEARANCES FOR 48" MODELS
_1 27-1/2"to
_'_e!/g2,,t
Locategas
inlet onback
wall or on
floor2" from
backwall.
UniversalUtility Locations
WARNING:
Installations without a hood
require/48" minimum to combustibles
above the rangetop. A custom hood
installation with exposed horizontal
combustible surfaces must have
an Auto-On feature. Refer to hood
installation instructions for specific
hood clearances.
The surface of the entire back wall
above the countertop and below
the hood must be covered with
a non-combustible material such
as metal, ceramic tile, brick, marble
or other stone.
13"Max.
18"Min.
48" Minimum "
to Combustibles
\
material 12"Minimum
Side
/.- 46-1/4"
22-3/4"Min.
\\ i2" Minimumto
AdjacentWall
2-1/2"
* The opening between a 4" high backsplash must be 48"
to allow the rangetop to slide back against the wall.
ADDITIONAL CLEARANCES:
Allow 12" minimum clearance to an adjacent wall on
each side.
Working areas adjacent to the rangetop should have
18" minimum clearance between countertop and the
bottom of the wall cabinet.
12"Minimumto
Combustiblesor0" to /
non-combustiblematerial
abovethecookingsurface
48" Min. to
Combustibles
1
0" iClearance
4

Design Information
PRODUCT DIMENSIONS AND CLEARANCES FOR 36" MODELS
38-7/8"Width 27-1/2"to
Frontof
Height
Locategas
inleton back
wall or on
floor2" from
backwall.
Universal Utility Locations
2"
17"J_
16"
WARNING:
Installations without a hood
require 48" minimum to combustibles
above the rangetop. A custom hood
installation with exposed horizontal
combustible surfaces must have
an Auto-On feature. Refer to hood
installation instructions for specific
hood clearances.
The surface of the entire back wall
above the countertop and below
the hood must be covered with
a non-combustible material such
as metal, ceramic tile, brick, marble
or other stone.
13"Max.
18"Min.
1
48" Minimum
to Combustibles
12"Minimum
EachSide
* The opening between a 4" high backsplash must be 36"
to allow the rangetop to slide back against the wall.
ADDITIONAL CLEARANCES:
Allow 12" minimum clearance to an adjacent wall on
each side.
Working areas adjacent to the rangetop should have
18" minimum clearance between countertop and the
bottom of the wall cabinet.
12"Minimumto
Combustiblesor0" to /
non-combustiblematerial
abovethe cookingsurface
_L_ 48" Min. to
Combustibles
5

Design Information
INSTALLATION OPTIONS
8" i
Countertop
Level
Backedge
of chamfer
-4 ......................................................28-13/16"
ToFrontof Control Knobs
27-1/2" ................................................................
ToFrontof Bullnose
I \ !_ I ")
Finishedback edge _1-_I
"_-- of control panel 6-1/2" k}
I u
....... 26" _-
28-3/4" D,
ToFrontof Control Panel
* Hinimum cabinet cutout depth from
the back of the rear trim to the back
finished edge ofthe control panel -
tgpicallg, the minimum cabinet depth
(front to back). Haximum cabinet cutout
depth is 26" minus the countertop
overhang.
t Includethe overhangofthe reartrim when countertop continuesbehindthe product.
Theoverhangisdecorativeonlg.Theweight ofthe rangetop isfullgsupported bgthe sidetrims.
1/2"
T Countertop
Level
•_ t 3/32"
1-3/16"
1-1/32"
ToPipeStub
Center
** Maximum countertop cutout depth
from the back ofthe rear trim
to the back edge of chamfer at the
sides of the control panel - tgpicallg,
the maximum countertop cutout depth
(front to back).Minimum countertop
cutout depth is 25-t/4".
0
Rangetop
1/2" AboveAdjacent
Countertops
Rangetop
1/2" Above Adjacent
Countertops
Control panel projects forwards from
standard depth cabinets. Front of deep cabinets can align with control
panel beveled edge.

Installation Preparation
TOOLS REgUIRED
SaberSaw
MeasuringTape
Carpenter'sSquare
SafetyGlasses
Phillips#2 Screwdriver
Level
Drilland
AppropriateBits
AdjustableWrench
1/4"DriverorWrench
HandTruck
MATERIALS PROVIDED
Hold-Down Regulator
Strap
MATERIALS REgUIRED (not provided)
ShutOff Valve
Joint PipeFittings
Sealant
5-foot maximum length, 5/8" O.D.CSA-approved
flexible metal gassupply
(3-foot maximum length in Massachusetts only)
NOTE: Purchasenew flexible line; do not use
previously usedflexible gas line.
POWER SUPPLY LOCATIONS
Gas Supplg:
• The natural gas models are designed to operate at 5"
water column pressure. For proper operation, the
pressure of the natural gas supplied to the regulator
must be between 7" and 13"water column.
• The LP models are designed to operate at 10" water
column pressure. For proper operation, the pressure
of the LPgas supplied to the regulator must be between
11" and 13"water column.
• Locate the pipe stub on the back wall or floor
(see"Product Dimensions and Clearances"). Use 5-foot
maximum length, 5/8" O.D.flexible gas supplg line
(3-foot in Massachusetts).
• Install a manual shut-off valve in the gas line
(not provided), in an easilg accessible location. Make sure
the homeowner knows where and how to shut off the gas
supplg to the rangetop.
Electric Supplg:
These rangetops must be supplied with 120 volt, 60 Hz.,
and connected to a dedicated, properlg grounded branch
circuit protected bg a 15 amp circuit breaker or time
@lag fuse.
The power cord of this appliance is equipped with a
three-prong (grounding) plug which mates with a standard
three-prong grounding wall receptacle to minimize the
possibilitg of shock hazard from this appliance.
If the electrical service provided does not meet the above
specifications, it is recommended that a licensed electrician
install an approved outlet.
DO NOT,UNDERANY
CIRCUMSTANCES,CUT
ORREMOVETHETHIRD
(GROUND)PRONGFROM
THE POWERCORD.
DO NOTUSEAN EXTENSION
CORDWITH THISAPPLIANCE.
• Locate the electric supplU
ReceptacleBoxCoverPlate
ThreePrig Plug
ThreePron Receptacle
within the area shown or within reach of the rangetop's
four-foot power cord.
•To avoid tangling cord with items stored in the cabinet,
locate the receptacle on rear wall, inside the cabinet.

Installation Preparation
REMOVE PACKAGING
CAUTION
Stand clear. The ends of the cut metal banding may
snap toward gou.
.Cut the metal banding.
. Remove packaging tape and foam.
Dispose of packaging materials properlLI.
.Remove grill/griddle covers, grill grate and burner
grates.
. Lift out cast-iron griddle flue cover, grease
troughs and pads.
.Cut the ties holding the grill grate to the grill frame.
GriddleFlueCover
Ties seTroughs
. Lift off burner caps and remove foam pad,
then lift off burner heads and remove foam pad.
RemoveFoamPads

installation
STEP 1
Allow Additional
ClearanceBelow
the RangetopBurner
Boxfor the Regulator
andGasConnections
Allow Additional
ClearanceBelow
the RangetopBurner
Boxfor the Regulator
andGasConnections
............ _so"
va_ 8U
A 'ash ................_ to36"
BackSP! 12" j_
8-1/2"
.1/2" 2-1/2"
48"wide modelsaredesignedto fit in48"or wider basecabinets
Measure curefullu when cutting the countertop.
Make sure sides of the opening are parallel.
• Allow 8" free space below the top surface of the countertop.
Allow additional clearances below the burner box
to install the regulator and make house supplu
connections. Use a 90° elbow to route the gas
connections and limit interference with drawers
or other cubinetru features.
• These rangetops are designed to hang from
the countertop bu their side flanges.
Smooth anu rough edges on the countertop before
installing the rangetop.
- Formica countertop edges must be finished.
The countertop must be strong enough to support
the weight of the rungetop.
36"widemodelsaredesignedtofit in36"orwiderbasecabinets
Cutout Opening with False Bottom
Dimensiens
A (Dia.) B C D
36" Rangetop 7-3/8" 1-1/2" 7-1/2" 11-1/8"
48" Rangetop 8-1/4" 1-1/2" 7-1/2" 11-1/8"
• You can construct the cutout with afalse bottom to
conceal the bottom of the rangetop.
- Build the false bottom using asolid material; cut a
7-1/2" x 1!-!/8" hole in the left rear corner for the gas
inlet and power cord clearances.

installation
STEP 2 INSTALL RANGETOP
,Slide the rangetop into the opening. Make sure
the rangetop is evenly seated and supported.
,A hold-down strap with screws is provided to
secure the rangetop to the rear or side cabinet
walls.
. Remove the hold-down strap from the back
of the rangetop. Attach one end of the strap
to the back of the rangetop.
,Secure the other end of the strap as high as
possible to the cabinet back wall or adjacent
cabinet. Keep the strap as short as possible for
better security.
BackWall
Hold-Down
Strap
Locationand
Attachment
STEP 3 CONNECT RANGETOP TO GAS
-AWARNING
Do not use a flame to check for gas leaks.
A manual shut-off valve must be installed where
it will be accessible.
Assure that gas is turned off at the shut-off
valve.
.Install the supplied pressure regulator onto the end
of the gas inlet.
,You can install a 90 ° elbow (not provided) onto the
gas inlet and route the gas connections to avoid
interference with drawers or other cabinetry
features. However, it is not recommended because
it will result in a drop in gas pressure.
, Make sure the regulator is installed in the right
direction. See arrow on the underside of the
regulator.
NOTE: Instead of using solid piping to connect
to pressure regulator, an approved flexible metal
appliance connector may be used between the pipe
stub and the shut-off valve to the pressure regulator,
if local codes permit.
,Turn on gas and check for leaks:
-Use a liquid leak detector at all joints and
connections in the system.
RangetopBurnerBox
1/2" N.RT.
GasInlet
) Regulator
(Supplied)
Solid Piping
or Flexible
Connector
_ hut-Off
Valve
PipeStubFrom
HouseGasSupply
IMPORTANT: Disconnect the rangetop and the
individual shut-off valve from the gas supply piping
system during any pressure testing of that system
at test pressures greater than 1/2 psig. Isolate
the rongetop from the gas supply piping system
by closing the individual manual shut-off valve
to the rongetop during any pressure testing
of the gas supply piping system at test pressures
equal to or less than 1/2 psig.
10

installation
STEP 4 CONNECT ELECTRICAL
.Plug power cord into properly grounded
receptacle.
*Press the button on the left side of the control
panel. The lights above the knobs should
illuminate.
STEP5 CHECK BURNERS
Check to be sure that burner heads and cops
ore securely seated.
BurnerCapProperlySeated
BurnerCapNotProperlySeated
.Check for proper ignition:
- Push in one control knob and turn to LITE
position.
- The igniter will spark and the burner will light;
the igniter will cease sparking when the burner
is lit.
- First test mug require some time, while air
is flushed out of the gas line.
- Turn knob to OFF.
- Repeat the procedure for each burner.
IMPORTANT: If the igniter electrodes continue
to spark after the burners ore lit, check that
each burner component is assembled properly.
Refer to the Owner's Manual.
.Burner flames should be blue and stable with no
yellow tips, excessive noise or lifting of the flame
from the burner. If any of these conditions exist,
check that the burner ports ore not blocked.
If one of these conditions continues, cull for
service.
FINALIZE INSTALLATION
Place the burner grates over the burners.
The grates should be seated and should not rock.
The griddle is secured with screws. It is designed
to be stationary and should not be removed.
The griddle has two leveling screws beneath
the rear flue cover that con be used to adjust
to the desired slope.
GriddleFlueCover
ClampingScrews
The two inner screws ore clamping screws for
securing the griddle in place. Loosen these two
screws before leveling. Do not remove these two
screws.
The two outer screws ore leveling screws. Do not
remove these two screws. They con be turned to
level the griddle or to provide o forward slope to
help grease and oils to drain away from the food
being cooked.
After leveling the griddle, hand-tighten
the clamping screws; do not over-tighten.
ll
INSTALLATION CHECKLIST
0 Make sure oil controls ore left in the OFF
position.
0 Make sure the flow of combustion and
ventilation air to the rongetop is unobstructed.
0 The serial plate for your rongetop is located
on the bottom of the rongetop. In addition
to the model and serial numbers, it tells you
the ratings of the burners and the type of fuel
and pressure the rongetop was adjusted
for when it left the factory.
0Recheck Steps:
Double check to make sure evergthing
in this manual has been completed. Rechecking
steps will ensure safe use of the rangetop.

Z×12B30PSS,ZX12B36PSS,ZX12B48PSS AccessorgInstallation
OPTIONAL ACCESSORIES--12" HIGH BACKSPLASH
AWARNING:
To prevent ignition of combustible materials,
the entire back wall above the range must
be protected bg a backsplash constructed
of non-combustible material.
This stainless steel backsplash accessorg
must be installed in combination with a custom,
non-combustible backsplash built begond
the 12" height of the backsplash.
BEFORE YOU BEGIN
Read these instructions completelg
and carefull£1.
IMPORTANT: Save these instructions for local
inspector's use.
IMPORTANT: OBSERVE ALL GOVERNING CODES
AND ORDINANCES.
NOTE TO INSTALLER: Be sure to leave these
instructions with the Consumer.
NOTE TO CONSUMER: Keep these instructions
with gout Owner's Manual for future reference.
This kit provides for the installation of a 12" high
backsplash for 30", 36" or 48" Monogram
Professional Ranges and Rangetops.
TOOLS AND MATERIALS REQUIRED
,Gloves to protect against sharp edges
, T-15 and #2 Phillips screwdrivers Wall Support
, Drill with 3/32" and 9/64" bits Panel
/
,Safetg glasses _:
, Level
, Pencil
This KitIncludes
, Wall support panel
, Cover panel
, Hardware package with
- 5 Stainless Steel Torx 15 #8
self-tapping screws
- 5 Phillips #2 pan head wood
#10 screws
Hardware
Package
INSTALL 12" BACKSPLASH
WARNING:Thisbacksplashmust
be securely fastened to the wall. Failure to do
so could result in damage or personal injury.
, Install and level the range or rangetop and the
range hood according to the installation
instructions.
, Remove the bocksplash packaging and
protective film.
, Use a level to pencil o horizontal line on the wall,
1/8" above the range or rongetop. The 1/8" gap
allows the cover panel to overlap the wall support
panel.
, Locate wall studs on each side. Where studs ore not
available, plan to use wall anchors (not provided).
, Align the wall support panel on the marked
horizontal line and centered left to right.
, The wall support panel must be secured to the wall
at oil 4 corners. Use wood screws (provided) or wall
anchors (not provided) to secure the support panel
to the wall.
Place the cover panel over the wall support
panel and secure with Torx screws (provided).
Install 2 screws on each side.
1/8" ........
Install4 Wood
Screws wa
Panel
Wall
Support
Panel
CoverPanel _> InstallT-15
Screws
12

ZXADJB30PSS,ZXADJB36PSS,ZXADJB48PSSAccessorg Installation
ACCESSORIES--30" TO 36" ADJUSTABLE BACKSPLASH {notincluded}
WARNING:
To prevent ignition of combustible materials,
the entire back wall above the range must
be protected bg a backsplash constructed
of non-combustible material.
BEFORE YOU BEGIN
Read these instructions completelg
and carefullg.
IMPORTANT: Save these instructions for local
inspector's use.
IMPORTANT: OBSERVEALL GOVERNING CODES
AND ORDINANCES.
NOTETO INSTALLER:Be sure to leave these
instructions with the Consumer.
NOTETO CONSUMER: Keep these instructions
with gout Owner's Manual for future reference.
• This backsplash adjusts to fit the space between
the top of the range and the bottom of the hood,
from 30" Min. to 36" Max. height.
• Maximum shelf load-bearing weight is 40 Ibs.
TOOLS AND MATERIALS REQUIRED
, Gloves to protect against sharp edges
, T-15 and #2 Phillips screwdrivers
, Drill with 3/32" and 9/64" bits
, Safetg glasses
, Level TopCover
, Pencil with Shelf
TopWall
Support
This KitIncludes
, Top wall support
, Bottom wall support
, Top cover with shelf
, Bottom cover BottomWall Support
, Hardware package with
- 9 Stainless Steel Torx 15 #8
self-tapping screws
- 9 Phillips #2 pan head wood #10 screws
- 3 Stainless Steel #2 truss head
#10 screws (for alternate
installation method)
Hardware
Package
INSTALL THE WALL SUPPORT PANELS
13
AWARNING: Thewa,supportpanels
must be securelg fastened to the wall. Failure to
do so could result in damage or personal injurg.
IMPORTANT:Thisbacksplash isdesignedto cover the wall
between the bottom of the hood and the top of the range.
The vent hood should be installedover the rangetop or
range before installing this backsplash.
• Installand levelthe Range/Rangetop according
to the product installation instructions.
Removebacksplash packaging and protective film.
Locatewall studson each side.Wherestuds are not
available, plan to usewall anchors (notprovided).
Usea levelto pencil 2 horizontal lineson the wall,
one 1/8" below the vent hood and the other 1/8" above
the Range/Rangetop.This 1/8" space allows the cover
panels to overlap the wall supports.
• Securethe top wall support panel to the wall with 4 wood
screws,through the outermost studs.
• Use4 wood screws to securethe bottom wall support
panel.Thecenter slot should be positioned at the top.
The gap between the top and bottom support panels
will be covered bg the top cover with shelf.
1/8"
Securethetop
paneltothewall
with 4 wood
screws
Wood
Screws Secure
the bottompanel
to thewall with
4 woodscrews

ZXADJB30PSS,ZXADJB36PSS,ZXADJB48PSSAccessorg Installation
INSTALL COVER PANELS
See alternate method if side access is blocked.
, Hold the bottom cover over the bottom support
while driving one screw (provided)into each side.
, Place the top cover with shelf over the top wall
support. If you have access to the sides, secure
the panel with two screws on each side.
, Secure the top cover with shelf to the top
support with screws through the front of the panel,
at the top corners. Use one screw on each side.
Install
Install
Screw
InstallCornerScrews
INSTALL COVER PANELS (cont.}
ALTERNATE METHOD: When side access is blocked
. Install bottom cover over the bottom support while
driving one screw into each side.
, Hold top cover in place while marking screw
locations,just below shelf support and onto bottom
cover.
. Remove the shelf and drill a 9/64" diameter
hole in the pencil-marked locations.
, Mount the top cover over the top support
and secure the front cover with screws through
the drilled holes on each side.
Install screws through each top corner.
Marl<ScrewLocations
for AlternateMethod
"- InstallScrew
"'_" onEachSide
InstallScrewinTopCorneronEachSide
14

I
Istallti
str cti Convert Natural Gasto LPGas Operation
Convert LPGasto Natural Gas Operation
-AWARNING:Thisconversionmust
be performed bg a qualified installer or gas supplier
in accordance with the manufacturer's instructions
and all codes and requirements of the authoritg having
jurisdiction. Failure to follow instructions could result
in serious injurg or propertg damage. Thequalified
agencg performing this work assumes responsibilitg
for the conversion.
-AWARNING:The rangetop, as shipped from
the factorg, is set for usewith its intended gas. If gou
wish to use your rangetop with the alternate gas, you
must first replace the orifices and convert the pressure
regulator.
-AWARNING:Thefollowing adjustments must
be made before turning on the burner. Failure to do so
could result in serious injury. Besure pressure regulator
has been converted asdescribed in Step 2.
TOOLS YOU NEEDED FOR CONVERSION
CrescentWrench 1/4" and7mmNutdrivers
SafetyGlasses
1/2" Deepwell
SocketWrench
SmallFlat-HeadScrewdriver
(2 to2.4mmor3/32" tip size,
60mmlong)
SmallPliers Philips
Screwdriver
Griddle
ORIFICE HOLDER Orifice Grill
Orifice
Therange orifice holder
islocated behind the front
access panel atthe bottom
of the range.
Therangetop orifice holder BurnerOrifices
islocated insidethe range insulation cover.
Additionalorifices maUbe present. UseonlUthe orifices
specifiedin the instructions for gour range or rangetop.
_-_ CONVERT THE REGULATOR
Disconnect all electrical power at the main circuit
breaker or fuse box.
A. Removethe rearvent RangeRegulator
trim (onranges onlU)
to accessthe
regulator.The
Rancjetopregulator is
on the left bottom
corner.
B. Shutoffthe gassupplg bg closing the manual shut-off
valve in the unit or at t_newall.
C. Convertthe pressureregulator:
• Unscrewthe cap with plunger.
Placeyour thumb against flat sideofthe plunger and
pressdown to snapthe plunger out otthe cap.
CarefullUlookat the plunger to locate the NAT
or LPposition.
•Turnthe
plunger
overso
that the
desiredgas
isshowing
nearthe
bottom.
Cap G,asket
@
2_ _ _Plunger
NAT.Position/_
Position
PressureRegulator
• Snapthe plunger back into the cap.
• Screwthe cap back onto the regulator.
iTI CHANGE BURNER ORIFICES
INSTALLATIONTIP:Firstremoveall
orificesand then start replacingthem.
Thiswill helpto prevent the possibility
that some mag not be replaced.
A.
B.
BurnerCap
Burner
Removethe burner grates, Head
burner caps and burner heads.
Loosenthetop burner Spark --__%,
orificesusing a 7 mm Igniter
nut driver.Usesmall
pliersto carefullg lift out the orifices. BurnerBase
Themain orifice islocated
low in the center of the
burner,while the simmer
orifice islocated higher
besidethe center
of the burner.
Orifice
Orifice
15

Installation Instructions for Gas Conversion
[-_ CHANGE BURNER ORIFICES {cont.}
IMPORTANT: Find your model number below. Read
each orifice label to identify and install them in the
exact locations shown.
ZDP304 SIMMER ORIFICES
A 34SL or 52SN orifice
will be used on ell burners.
ZDP304 MAIN ORIFICES
will be used
on these three
burners.
Use a 108XL
or 190XN orifice
forthe right
frontburner.
ZDP364, ZDP366, ZDP484, ZDP486
SIMMER
ORIFICES
MAIN
ORIFICES
A 34SL or 51SN orifice
wiJl be used on ell
burners.
J
LP Nat Use 108XL or
__ 190XNor,fices
forell burners.
A. Return the unused orifices to the holder. Reattach
the holder and the instruction sheet with screw
in the original storage location.
B. Replace the burner heads, caps and top grates.
On range models,replace rearvent trim.
CHANGE GRILL ORIFICE (if present)
Locatethe 1-1/2" long Grillorifice.
Selectfor gour gastgpe.LP--.047, NAT--.067
A. Removethe grill cover,
grates and grote frame. Lift
the radiant baffle straight
up and off.
B. Removethe 2 hex
head screws from
the top of the igniter.
• Removeone screw
from eachsideof
the burner surround.
• Liftout the surround.
IIIIIIIII IIIIIIIIIIIIIIIIIIII IIIIIH
<
C. Carefullgpushthe Burner
igniter asideand Surround
under
the burner.
Donot pull or pinch
the wire.
Remove4 burner
attachment screws,
2 at the front and 2
at the back.Slidethe
burner assemblg
toward the back and
out of the gas inlet.
D. Usea 1/2" deep well Frontof Range
socketto remove ht
and replacethe orifice. _m,
/i
Reversethese _ ............
stepsto re-assemble
the grill.Besureto
placethe unused
orifice in the holder ,
for possiblefuture use.
igniter
Burner
Assembly
16

Installation Instructions for Gas Conversion
[_ CHANGE GRIDDLE ORIFICE (if present}
Locatethe3/4" longGriddleorifice.
Selectfor yourgastype. LP--.047, NAT--.076 [--]
A. Liftoff
the griddle flue
cover Remove
the 2 inside
clamping
screws.
B. Usea pad or
pieceof
carton to
protect
the adjacent
surface.Slide
the griddle
toward
the rear
and outof
thehold-downtabsalong
thebottom.
C.CAREFULLYliftand hold
thegriddle.A thermostat
capillaryisroutedthrough
a clip.Gentlyliftthegriddle
toonesideand slipthe
capillaryoutoftheclip.
D.Laythegriddle
onthepaddedsurface.
Do notdisconnectorpull
onthecapillary.
E.Removethe2 burner
hold-downscrews
attherearoftheburner.
• Pulltheburnerstraight
backtowardtherear
andoutofthegasinlet.
F.Usea i/2"deepwellsocket
toremoveandreplace
theorifice.
GriddleFlueCover
A
•NOTE:Remove
screws
)ositionedon
insideonly.
Donot remove
the outermost
screws--they
arefor leveling.
Capillary
Backof Range F Frontof Range
////tI tJI b FI i tll
Reversethesestepsto re-assemblethe griddle.Pushexcess
capillarybackintotheentry hole.Routethethermostat
capillarysoit isheldby theclip.Placethe unusedorificein
theholderfor possiblefutureuse.
ADJUST BURNER FLAMES
Normally, burners do not need further adjustment.
Hake adjustments only when necessary.
A. Turn on the gas. Plug in electrical cord.
B. Turn all burners on highest setting and check
the flames. They should be blue in color. When
using LPgas, the flames may have some yellow
tipping at the ends of the flame. Foreign particles
in the gas line may cause an orange flame at first,
but this will soon disappear.
C. Turn the burner knob to "LO" while observing the
flame.
Adjust the setting of the upper row of flames using
the valve bypass screw as follows:
Adjustments must be made with two other burners
in operation on a medium setting. This prevents
the upper row of flames from being set too low,
resulting in the flame being extinguished when
other burners are turned on.
D. Toadjust the flame, remove the knobs. Insert asmall
flat-blade screwdriver into the hole in the center
of the valve stem to engage screw.
. If the flames are too small or flutter,
turn the screw counterclockwise.
C
. If the flames are too large, turn the screw
clockwise.
E. Make the adjustment by slowly turning the screw
until flame appearance is correct.
mOncethe conversion iscomplete and checked,fill out the conversionlabel and affixthe label near the rating label.Forranges, I
place the label beneath the control panel.Forrangetops,placethe labelon the bottom of the unit.
17

Consignes de s curit
AVANT DE COMMENCER
Lisez attentivement i'ensemble des consigneso
•IM PORTANT-Conservezcesconsignes,elles
peuventvous @treutilespourtouteinspectionde votre
installation.
"IMPORTANT- Respecteztouteslesnormes
oinsique lesrecommondotionspr@conis@esparles
outorit_s comp_tentes.
• Remarque 6 I'attention de I'installateur-
Apr_s intervention, ossurez-vous d'ovoir remis ces
instructions 6 I'utilismteur.
• Remarque 6 I'ottention de I'utilisoteur-
Conservez ces instructions ovec le manuel de
I'utilisoteur pour toute consultation ult_rieure.
• Temps d'installation - 1 a 3 heures.
• II incombe 6 I'installateur de veiller 6 la bonne
installation. Toute d6faillance du produit due 6
une installation non conforme ne pourra #tre
couverte par la garantie. Pour tout compl#ment
d'information, reportez-vous au manuel de
I'utilisateur.
AVERTISSEMENT
Cet opporeil doit _tre correctement mis 6 Ioterre.
Reportez-vous 6 Iosection "Alimentotion _lectrique".
Pour contocter le service de d_ponnoge Monogram le
plus proche de chez vous, veuillez t_l_phoner ou num_ro
suivont :
1.800.444.1845.
Pourcontocterleservicede d_ponnoge Monogram du
Canada, veuillez oppeler le num_ro suivont
1.800.561.3344.
Pour contocter le centre d'occessoires et de pi_ces
d@toch_esMonogram, veuillez t_l@phonerou num_ro
suivont
1.800.626.2002.
If gou received o damaged rongetop, gou should contact
gour dealer.
Dons le Commonwealth of Massachusetts
(Communout@ du Massachusetts} :
, Ceproduit dolt _tre instoll_ par un plombier ou un
technicien de goz domestique ogre&
, Sivous utilisez des robinets de goz, ceux-ci doivent _tre
de type 1/4 de tour.
. Sivous utilisez un roccord 6 goz flexible, celui-ci ne
dais pos mesurer plus de 3pieds (100 cm).
Dispositions de hotte
d'extracbon
IIest recommond@d'instoller nos tables de cuisson sous
une hotte d'extroction odopt_e.
. Instollez une hotte disposont d'une copocit_
d'_vocuotion d'ou mains 1200 CFM6 une distance
de 48" (122 cm) de Io table de cuisson.
. Instollez une hotte disposant d'une copacit@
d'@vacuation d'ou mains 600 CFMou dessus d'une
table de cuisson de tgpe 36" (91 cm).
Cot oppareil produit une importante quantit@de chaleur
et de ce fair, vous devez porter une attention route
particuli_re 6 I'installation de Iohotte oinsi qu'6 celle de Io
conduited'o_rotionofinde vousassurerqu'eller_pond
oux normes de constructione vigueurdons votrer@gion.
AVERTISSEMENT :
vous trouverez ci-dessous les espaces qui doivent @tre
respect@sentre Io surface de la table de cuisson
et le plafond ou encore toute surface horizontole
se trouvont ou-dessus de Iotable de cuisson •
. Pour les installations d_pourvues de hotte, pr@vogez
un espace minimum de 48" (122 cm) entre I'oppareil et
tout @l@mentinflammable situ@ou-dessus de celui-ci.
. II est possible d'instoller une hotte sp@ciale6 proximit@
d'@l@mentshorizontoux inflammables dans la mesure
oOcelle-ci dispose d'une fonction de mise en morche
outomotique.
. Pour obtenir lessp@cificotions relatives oux espaces
d'outres installations pourvues d'une hotte, veuillez
vous reporter oux instructions fournies ovec celle-ci.
,ATTENTION :
nos tables de cuisson sont extr_mement Iourdes. Afin
d'@vitertout risque de blessure ou d'endommogement
de I'appareil et tenant en compte le poids oinsi que
la toille de Io cuisini@re:
DEUXPERSONNESSONTNECESSAIRESPOURUNE
INSTALLATIONADEQUATEDEL'APPAREIL
L'installation doit respecter les normes @tabliesdons votre
[e-mail] I'absence de celles-ci, Io table de cuisson doit
@treinstall@esuivant la derni_re @ditiondu National Fuel
GasCode, ANSIZ223.1/NFPA5/4,e.tla derni@reraise 6 jour
du National Electrical Code ANSI/NFPA70.Au Canada,
I'installation doit respecter la Ioien yigueur sp@cifi@epar le
Natural Gas Installation Code, CAN/CGA-B149.1ou le
Propane Installation Code, CAN/CGA-B149.2en vigueur, et
ses lois qui entrent dons son domaine d'application. Cette
cuisini_re a @t_conque et certifi@epar CSAInternational
et dons le respect de la derni@re_dition de la norme ANSI
Z21.1,oinsi que le Canadian Gas Association (Association
canadienne du gaz) et dqns le respect de la derni@re
@ditionde la norme CAN/CGA-I.1.
Veuillezvous reporter oux consignes du fabricant pour
v@rifierla pr@sencede fuites.
18

Caract ristiques
TABLE DES MATII_RES
Caract_ristiques
ModUles disponibles ............................................................19
Accessoires du dosseret ....................................................19
Dimensions du produit et espaces requis pour les
mod@les d'une largeur de 48" (122 cm) ....................20
Dimensions du produit et espaces requis pour les
modules d'une largeur de 36" (91 cm) ........................21
Options d'installation ........................................................22
Preparation de I'installation
Outils et mat6riel requis ..................................................2:3
Emplacement des alimentations ................................2:3
Sortez I'appareil de son emballage ..............................24
Consignes d'installetion
Etape 1, D#coupez I'ouverture sur leplan de travail ........25
Etape 2, Installez la table de cuisson ........................26
Etape 3, Raccorder la table de cuisson a I'alimentation
en gaz ........................................................................................26
Etape 4, Branchez a la prise 61ectrique ....................27
Etape 5, V6rifiez les brQleurs ..........................................27
Terminez I'installation ........................................................27
Liste de v6rification pour I'installation ......................27
Installez le dosseret de la table de cuisson ............27
Installation d'accessoires ..........................................28-:30
Conversion de gaz ........................................................31-33
MODI_LES DISPONIBLES
Les tables de cuisson Monogram sont conques en
usine pour le gaz naturel ou pour le gaz propane.
Commandez le mod61e correspondant a votre
installation domestique.
ModUles 6 gaz 48" I:122 cm} :
ZGU484NG - 4 brQleurs a gaz, grill et plaque
chauffante
ZGU486NR- 6 brQleurs a gazet grill
ZGU486ND - 6 brQleurs _]gazet plaque chauffante
ModUles 6gaz GPL 48" I122 cm} :
ZGU484LG - 4 brQleurs a gaz, grill et plaque
chauffante
ZGU486LR- 6 brQleurs a gazet grill
ZGU486LD - 6 brQleurs a gazet plaque chauffante
ModUles 6gaz naturel 36" 191 cm}:
ZGU364ND - 4 brQleurs _]gaz et plaque chauffante
ZGU364NR- 4 brQleurs a gazet grill
ZGU:366N - 6 brQleurs a gaz
36" LP Gas Models:
ZGU364LG - 4 br01eurs a gazet plaque chauffante
ZGU:364LR - 4 brQleurs a gazet grill
ZGU:366L - 6 brQleurs a gaz
DOSSERET
Tous les modules requi_rent au minimum 12"
(30 cm) d'espace de s6paration arri_re avec toute
surface inflammable. Si cet espace est inf6rieur
12" (:30cm), la totalit_ de la surface du mur
se trouvant au-dessus du plan de travail et la table
de cuisson dans toute sa largeur doivent _tre
prot6g_es par un dosseret. Le dosseret doit _tre
fabriqu6 a I'aide d'une mati_re ignifuge comme
le m6tal, la tuile en c_ramique, la brique, le marbre
ou tout autre pierre.
Deux dosserets sont disponibles :
. II existe un dosseret de 12" (30 cm) en acier
inoxgdable. Utilisez ce dosseret coupl6 (_un
dosseret sp6cial et ignifuge mont6 au-dessus du
premier. La hauteur des deux dosserets combin6s
doit atteindre la partie inf6rieure de la hotte, ou en
I'absence de hotte, la hauteur totale a partir de la
surface de cuisson doit atteindre les 48" (122 cm).
. II exist un dosseret adjustable de :30"(76cm) - 36"
(91cm). Ce dosseret comble Iespace entre
le dessus de la cuisini_re et la partie inf6rieure
de la hotte. L'6tag_re est congue pour que les
ampoules d'une t_otte professionnelle Monogram
soient orient6es vers elle.
D0sseretde12"(30cm)dehauteur
ZX12B48PSS,pourlescuisinieresde48"(122cm)
ZX12B36PSS,pourlescuisinieresde36"(91cm)
D0sseretavecetagerede30"(76cm)a36"(91cm)
r_glableenhauteur
ZXADJB48PSS,pourlescuisinieresde48"(122cm)
ZXADJB36PSS,pourlescuisinieresde36"(91cm)

Caract ristiques
DIMENSIONS DU PRODUIT ET ESPACES DE SI_PARATION
DE 48" {122 CM}
47-7/8"(117 27-1/2"
(67cm)de
_-profondeur
8#/16" (19cm)
dehauteur
PlacezI'arriv6ede
gazsur le panneau
arriereousurla base,
a2" (5cm)du
panneauarriere.
POUR LES MODI_LES
Emplacementsde raccerd universels
AVERTISEMENT :
Pour les installations d_pourvues
de hotte, pr_vogez au minimum un
espace de 48" (122 cm) entre I'appareil
et toute mati_re inflammable. IIest
possible d'installer une hotte sp_ciale
d proximit_ d'_l_ments horizontaux
inflammables duns la mesure oOcelle-ci
dispose d'une fonction de mise en marche
automatique. Pour obtenir les
specifications d'espace pour d'autres
installations pourvues d'une hotte, veuillez
vous reporter aux instructions fournies
avec celle-ci.
13"(33cm)
Max.
18"(46cm)Min.
La totalit@de la surface du mur arri_re
ainsi que la surface se trouvant au-dessus
de la table de cuisson dolt @trefaite d'une
mati_re ignifuge comme
le m@tal,la tulle en c_ramique,
la brique, le marbre ou tout autre pierre.
t
A 48" (122cm)de
toutemat@iau
inflammable
\
46-1/4........
22-3/4"
(54cm)Min.
48"
(122cm)
o
-- I\\\\\\\ A 12"(30,4cm)dumur
adjacent
Mat6riauignifuge
12"(30,4cm)
dechaquec6t6
7/8" 22-1/2"
* L'espace pr_vu pour le dosseret de/4 cm de hauteur doit
@trede 48" (122 cm) afin de pouvoir coulisser la table de
cuisson centre lemur.
ESPACES DE SI_PARATION SUPPLI_MENTAIRES :
Pr@vogezau mains 12" (30,4 cm) d'espace de s@paration
et de chaque c6t@d'un mur adjacent.
Leszones de travail adjacentes 4]la table de cuisson
doivent disposer de 18" (/45.7cm) d'espace de s@paration
entre la table de cuisson et la partie inf@rieuredu placard
mural.
unedistanceminimum
de 12"(30,5cm)des
mat@iauxinflammables
oude 0" desmat@iaux
ignifugesau-dessus
dela surfacedecuisson T
S@arationmin.
de48" (122cm)
detoutematiere
inflammable.
_0" (0cm!de%
s6paratlonIJ
2O